HW:Find the production rate of the wheel-tractor-mounted loader, using thefollowing information:- Bucket capacity, 2.3 m'- Loose volume of handling material, 1480kg/m- Swell, 20%- Tractor operating factor, 52 min/hr- The unit is equipped with a torque converter and a power-shifttransmission, having the following speed ranges, forward and reverse:speed ranges, forward and reverse (km/hr)Low rangeintermediate range0-60-24high range0-48When hauling a loaded bucket, the unit should travel at an averagespeed of about 80% of its maximum speed in the low range.When returning empty, the unit should travel at an average speed ofabout 40% of its maximum speed in the intermediate range fordistances less than (40m), and at about 60% of its maximum speed inthe same range for distances equal and more than (40m).- The fixed time (load, shift, turn and dump) is equal to 0.35 min.Note: Tabulate the results for two distances: 24m and 48m.

Given, Bucket capacity (V) = 2.3 m3 Efficiency = 52 min/hr

Find the production rate of the wheel-tractor-mounted loader, using the following information: - Bucket capacity, 2.3 m - Loose volume of handling material, 1480kg/m? - Swell, 20% - Tractor operating factor, 52 min/hr - The unit is equipped with a torque converter and a power-shift transmission, having the following speed ranges, forward and reverse: speed ranges, forward and reverse (km/hr) Low range intermediate range high range 0-6 0-24 0-48

Find the production rate of the wheel-tractor-mounted loader, using the following information: - Bucket capacity, 2.3 m - Loose volume of handling material, 1480kg/m? - Swell, 20% - Tractor operating factor, 52 min/hr - The unit is equipped with a torque converter and a power-shift transmission, having the following speed ranges, forward and reverse: speed ranges, forward and reverse (km/hr) Low range intermediate range high range 0-6 0-24 0-48

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The settling basin for a type-1 suspension is to operate at an overfow rate of 0.76 m3/m2 ·h. The fow rate through the plant is 24,000m3/day. Determine the dimensions for a long rectangular basin,using a length to width ratio of 4:1. Depth should not exceed 4 m.Use more than one tank. Determine the detention time in the tankand the horizontal velocity.
Superimposed Deadload: 2.1 KPaLive load: 5.1 KPa
Calculate the nominal shear strength of a group of 2-legged stirrups 10 mm in diameter spaced at 120 mm on centers within the confinement region of a reinforced conerste be wide by 450 mm effective depth. Use fy = 450 MPa.
An ESP must treat 300,000 acfm with 99% efficiency. For an effective drift velocity of 0.25 ft/sec, calculate the required collection area. Assuming the plates are 15 feet tall and 6 feet long, and are arranged with three mechanical fields, calculate the aspect ratio. Estimate the total number of plates in this ESP. Estimate the cost of this ESP (f.o.b. Manufacturer and TIC), both in 1998 dollars.
Relevant technical criteria and other information for a railway route under investigation are given below. a) Calculate the maximum slope that can be applied in the tunnel on this route b) When the trains have to stop on this slope, verify whether they can tow their loads at the time of take-off. Locomotive power: 4000 kW Inrush slope: 8 kg/ton Rail-bandage friction coefficient = 250 kg/ton Tunnel resistance: 2 kg/ton
Critical path, Total float, Free float, Independent float A - 4 B - 3 C - 4 D A 5 E B 7 F C 4 G D 5 H F 7
1. In the upstream portion of a river, it has a rectangular channel 10m wide and 1.2m deep of water flowing with a mean velocity of 0.75 m/s. Determine the height (head H) in meters of a standard rectangular weir considered without contraction at the downstream portion, if the length of weir is half of the upstream channel width. 2. The river is measured through float method. It has a length marking of 10 meters. Trials were made for 10 times and tabulated the following recorded time in seconds: 12.4 15.5 16.8 17.1 14.9 14.4 16.6 17.2 18.2 15.8 Estimate the flow rate in m3/s of the river if the mean velocity is 75% of the maximum velocity at the top surface. The cross-section area of the channel is close to 15m x 2m.
Verticle load is 258 kN as opposed to 25*8kN - Apologies
how much is the shear load, Vs (kN), carrying capacity that a rectangular stirrup (where Av=2*Ab) spaced at 320mm if fy=280MPa? let the diameter of the stirrup = 10mm and the effective depth as 400mm.
Needed ASAP. A scow 50 ft long, 30 ft wide and 15 ft high has a draft of 9 ft. the center of gravity is at the center of the scow both longitudinally and transversely. If the scow tipped transversely until one side is in the point of submergence. Det. the righting couple.
Very urgent. F = 9 kN q = 3 kN/m L = 0.5 m
A fully loaded water-plane of a 420-m long supertanker has the following half-ordinates: 0.0, 8.9, 14.8, 22.8, 31.9, 25.6, 18.2, 12.2, 6.8. What is the water-plane area?