Find the scale ratio for the described below. map 1 mm (map) = 5 m (actual)
Q: pressure on a closed tank reads 68.86 kPa. What is the equivalent height in terms of Oil having a sp...
A: Given data- Pressure (P) = 69.86kpa Specfic gravity of oil(S) = 0.85 Density of oil (p) = 0.85 × 100...
Q: A 30m x 30m piece of land was purchased for the construction of a three-story building. The total ve...
A: Step 1: Case 1: Far below the case, Rw1=1, Rw2=1 qu = qNq Rw1+0.5γBNγRw2 qu = 20.1 X Df x 70.61 + 0....
Q: A building has to be supported over a raft foundation of dimensions 15 m x 25 m. The soil is clay ha...
A:
Q: less than the specified compressive strength,
A: If the beam's compressive stress in top fiber is less than the specified compressive strength, beam ...
Q: er. the Darcy velocity in the aquifer is 0.025 f/da- tio is 0.334. the longitudinal dispersion coeff...
A: given data contaminant mass of an aquifer =10 kg velocity =0.1 ft/day DL =0.01 ft2/day Dy =Dz =0....
Q: Four 28 bars are to be placed on a single layer in a beam having a width of 350 mm with shear reinfo...
A: Clear cover It is the distance between the outer face of any RCC member (column, beam, slab, and f...
Q: 5 B) Find y" for the function y =x + Vx at p(1,3)
A:
Q: Water flows over a dam from a depth of 8 m upstream the spillway to a depth of 1.5 m downstream. The...
A:
Q: Water at 300 K flows, under the influence of gravity, through a vertical packed bed of spheres 2 cm ...
A: Given- Temperature, T=300KDiameter of spheres, D=2 cm=0.02 mporosity, n=0.35
Q: Propane is flowing in a 4-inch schedule 40 steel pipe at the minimum rate for which the flow is turb...
A: Given fluid = propane dia of pipe (D)= 4 inch = 412feet length of pipe (L)= 50feet pipe material = ...
Q: Problem 3. The ladder has a uniform weight of 80 lb and rests against the smooth wall at B. If the c...
A: For a ladder of weight 80lb, if the motion of ladder restrain, then the angel of inclination with ho...
Q: Load Elongation o eng Eeng OTrue ETrue Lo |(mm)|(mm) F(KN)|SL(mm) No. Do 1 25 12.5 0.00 0.00 2 25 12...
A: Solution: From given table find the Stress and Strain; Engineering Stress/Strain: Stress=LoadAreaσen...
Q: A 300 mm wide reinforced concrete beam has an effective depth of 450 mm. It is reinforced in the com...
A:
Q: RL=105m V (U/s water level) RL=100m (D/s water level) 3m 6m Pile Pile 15m 10m 2m 8m For the above co...
A:
Q: QUESTION 2: For the state of stress shown in the figure, use stress transformation equations to dete...
A: Given data: σx=-60 MPaσy=-80 MPaτxy=50 MPa
Q: An artesian well with a radius of 0.75 meters was constructed to pump water from a source with a con...
A:
Q: In 1: 20 model of a spillway, the velocity and discharge are 1.5 m/sec and 2.0 m/sec respectively. F...
A:
Q: Water at 300 K flows, under the influence of gravity, through a vertical packed bed of spheres 2 cm ...
A: We have to determine the value of superficial velocity of the water flowing through the bed as per t...
Q: Find the nearest distance from the midpoint of the curve to the point of intersection of the tangent...
A: Point of curvature is defined as the point where curve alignment changes from straight line to circu...
Q: A 50-kg crate is attached to the trolley-beam system shown. Know ing that a = 1.5 m, determine (a) t...
A: Given ;
Q: The chords of a compound curve from PC to PCC and from PCC to PT are 130.60 m and 139.16 m, respecti...
A:
Q: Which of the following is/are TRUE about the Specific Gravity (Gs)? It is one of the most important ...
A: Which of the following is/are TRUE about the Specific Gravity (Gs)? The first 3 statements are true ...
Q: 3. Determine the critical net area of an L8 x 6 x1/2 with staggered holes in each leg as shown in th...
A:
Q: 45 mm 4 in. 10 mm E 30 mm 30 mm 150 lb 1.8 in. 9 kN 9 kN 500 lb B G 250 lb 400 mm 500 mm Problem 1 P...
A:
Q: 4.73 A 50-kg crate is attached to the trolley-beam system shown. Know- ing that a = 1.5 m, determine...
A:
Q: 32 3" fo=3000 ps fy= NWC = Mn=?, Tied bars. 28 = 60 ksi 多#9 14
A:
Q: Read the question carefully and give me both right solutions with clear calculations. A trapezoidal ...
A: step 1-
Q: In fig.if D1=1.5 cm, D2=1 cm V1= 1.25 * ?=m/s, V2 -Control volume (CV)- -Fluid element of velocity v...
A: Find value of V2=?
Q: A 45° sector gate is located on the crest of spillway. The water is upto the mid-point of the gate w...
A: step 1-
Q: The weir below is to be built such that the estimated average flow over its crest will be Q = 3000 m...
A:
Q: 8. Pile Capacity Calculations A 30" diameter friction pile which has a 24' length in contact with be...
A:
Q: A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The b...
A: Yield strength : When a material is stretched less than its yield stress, it will only undergo elast...
Q: Problem 6.87 The journal bearings at A and B only support vertical forces. The allowable bending str...
A:
Q: 14. Determine the force P required for equilibrium of the compound lever if Q = 4200 N. A. 420 N В. ...
A:
Q: Determine the stresses for each segment when the temperature of the rigid bar is -45 degrees celsius...
A: solution Given the temperature T=24°Fall in temperature Tm=-45°coefficient of thermal expansion α=11...
Q: A compound curve has a common tangent of 84.5 m long which makes an angle of 16° and 20° with the ta...
A:
Q: research or study? 5. What are the functions of litera
A: Hi! Thank you for the question As per the honour code, We’ll answer one question since the exact one...
Q: o be built such that the estimat mine the reguired flow oyer the
A:
Q: Find the moment about the bar's attachment point the wall (left side of drawing). on
A:
Q: 8X Ø EQ SPACED ON A Ø BC Use the attached diagram to fill in the bl...
A: ASKED: To complete the Standard Bolt Circle Callout. A BOLT CIRCLE (BC) is an imaginary circle pas...
Q: 38KN/m2 From the laboratory tests, the shear strength parameters obtained are c and ø=19°, the expec...
A:
Q: A canal slope is to be made in cutting at an angle of 30° to the horizontal in a soil having the pro...
A:
Q: The rated speed of a highway curve of 60-m radius is 45kph. If fk between the tires and the road sur...
A:
Q: A 300 mm wide reinforced concrete beam has an effective depth of 450 mm. It is reinforced in the com...
A:
Q: A soil sample taken from a field contains a volume of 110 cm3 , weighs 220 grams when taken, and 165...
A:
Q: What characteristics of a crop influence yield?
A: The various characteristics infuencing the crop yield are :- (1)Quality Of Seeds Agricultural produc...
Q: A roof truss has a span of 12 m and a rise of 2.4 m which is placed at 3.5 m c/c. Calculate the live...
A:
Q: 3. The circular shaft is supported by two journal bearings at A/C and B. internal shear force V(x) a...
A:
Q: Explain the physical significance of the above equation and give the type of jump you would expect b...
A: Physical significance of given equation and type of jump between section 2 and 3### Hydraulic jump #...
Q: Que. Find the discharge through a trapezoidal notch which is 2m wide at the top and 0.80m at the bot...
A: given- trapezoidal notch-width at top=2mwidth at bottom=0.8mheight, H=60 cm=0.6mhead of water of not...
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- What different methods can be used to show a map's scale? Select all that apply. bar scale contour lines representative fraction grid lines an equivalence relation giving the length of a fixed landmark such as a bridge or section of roadDETERMINING UNKNOWN SCALE. On a map of scale 1:25000, the map distance measured between points X and Y is 32.750cm. Determine the scale of a sketch of the same area in which the drawn distance between the same two points measures 10.916cm.On a map of scale 1:10,000,the map distance measured between points X and Y is 24.26cm.Determine the scale of a sketch of the same area in which the drawn distance between the same two points measures 11.18cm
- Measurements distance between two points A and B on unknown mapping scale found equal to 400 m. while measured the same distance at map have scale 1:200 found equal to 50 m find the mup scaleIf the equivalence scale of a map is 2 cm = 50 yard, what is the scale ratio?For a fractional map scale of 1:100,000, a measured distance of 1 meter represents an actual distance of.
- Please draw he contour line of the given figure below using 1-meter interval and its index contour and Base on the contour lines that you draw in item no.24, what kind of topographic landform is represented? please add a brief explanation thank youon a map scale 1:25000, the map distance measured between two points X and Y is 32:75 cm. Determine the scale of a sketch of the same area in which the drawn distance between the same two points measures 10.916 cm.Find the scale ratio for the map described below. 1cm(map)= 500km(actual)
- A map is drawn to a scale of 1 : 500. What distance does 145 mm on the planrepresent on the ground in meters?Survey Engineering: The size of a map was decreased in such a way that the original length of line 100 mm now measured 90 mm. Determine the new scale of the map if the original scale of the map was 1:1000.18 - Which of the following scales is used for the same area in a map, the detail of the map will be the most?A) 1 / 5.000B) 1 / 250.000C) 1 / 500.000D) 2 / 100.000E) 2 / 50.000