Find the stresses in a medium with a cylindrical hole under the action of radial tension or compression by the stress oo and the internal pressure p. Determine the stress concen tration coefficient. How does the stress concentration coefficient and stress distribution depend on the radius of the cavity?

Find the stresses in a medium with a cylindrical hole under the action of radial tension or compression by the stress oo and the internal pressure p. Determine the stress concen tration coefficient. How does the stress concentration coefficient and stress distribution depend on the radius of the cavity?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
The figure shows an element in bi-axial stress and the corresponding Mohr’s circle. Points A and B represents the stresses on the x face and on the y face of the element respectively. A. What is the value of the normal axial stress along x direction? B. What is the value of the normal axial stress along y direction? C. What is the value of the maximum shear stress?
According to the elasticity modulus of the material from which the cross-section is made, whose dimensions are given in the figure, E = 200 GPa and the effective bending moment M = 50 kNm; a) Draw the normal stress distribution in the cross section. b) Unit strain rate εz at point A calculate.
If the block is subjected to the centrally applied force of 600kN, determine the average normal stress in the material. Show the stress acting on a differential volume element of the material
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 75 MPa and Sy = 235 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 53°.
Show complete solution, include necessary figures. The major and minor principal stresses acting at a point are 80 psi compression and 20 psi tension.A. Draw the Mohr's circle for this stress combination.B. What is the maximum shear stress acting at the point and what value of normal stress acts on the plane?C. Determine the value of the normal and shear stress acting on a plane that is 30 degrees from the minor principal plane.
The rigid horizontal slab is attached to two identical copper rods. There is a gap Δ = 6.18 mm between themiddle bar, which is made of aluminum, and the slab. Neglecting the mass of the slab, calculate the stress in each rod when the temperature in the assembly is increased by 81°C. Use the following data:
A cylindrical tube of constant wall thickness t and inside radius r ¼ 10t carries a torque T. Find the expression for the maximum shear stress in the tube using (a) the torsion formula for a hollow shaft in Eq. (3.5d); and (b) the thin-walled tube formula in Eq. (3.8b). What is the percentage error in the thin-walled tube approximation? Please show complete solution and explain. Thank you.
A cylindrical tube of constant wall thickness t and inside radius r ¼ 10t carries a torque T. Find the expression for the maximum shear stress in the tube using (a) the torsion formula for a hollow shaft in Eq. (3.5d); and (b) the thin-walled tube formula in Eq. (3.8b). What is the percentage error in the thin-walled tube approximation? Please show complete solution. Thank you!
The bar shown in the figure has a square cress section for which the depth and thickness are 40 mm. If an axial force of 800 n is applied along the centroidalaxis of the bar’s crosssectional area, determine the average normal stress and average shear stress acting on the material along (a) section plane a-a (b) section plane b-b.)
Develop the shear stress distribution , volumetric flow rate, average velocity and point of maximum velocity for u =U
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 28 MPa, Sy = 39 MPa, and Sxy = 36 MPa. . Determine the maximum normal (principal) stress (in MPa) . Express final answer in 7 significant figures.