Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the brakes. He was travelling at 50 kph with perception-reaction time of 1.7 seconds. The skid resistance is 0.12 with 89% efficiency. Express your answer in 2 decimal places. Selected Answer: O93.76 Correct Answer: 23.61 ± 0.5

Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the brakes. He was travelling at 50 kph with perception-reaction time of 1.7 seconds. The skid resistance is 0.12 with 89% efficiency. Express your answer in 2 decimal places. Selected Answer: O93.76 Correct Answer: 23.61 ± 0.5

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 50P

See similar textbooks

Similar questions

34 Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the brakes. He was travelling at 37 kph with perception-reaction time of 1.5 seconds. The skid resistance is 0.23 with 86% efficiency. Express your answer in 2 decimal places.
A ball is thrown straight upward from the ground level. Its initial velocity is 30 m/s. 1. What is the maximum height it reaches in meters? a. 13.98 b. 45.87 c. 10.38 d. None of these 2. What is the total time in seconds when it goes back in the ground? a. 3 b. 6 c. 4 d. None of these
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place QUESTION #2: the water level in the tank 15 min. later (sample answer: 20,287.65 ft round off to 2 decimal place QUESTION #3: the volume change in the tank (sample answer: 20,287.65 cu ft round off to 2 decimal place
A basketball is thrown 35 degrees from the vertical. The distance of the player is 14 ft from the ring. Upon the release of the ball, it has a distance of 7 ft measured from the ground and 1 ft away from the player. Compute the velocity at release if the height of the ring is 10 ft. Please show complete diagrams and solution.
Two pipes, each 300m long 300 , are connected in series. The flow of water through the pipes is 150 L/s 0.15 with a total friction loss of 15m 15. If one pipe has a diameter of 300mm 0.3, what is the diameter of the other pipe? Neglect minor losses and assume f=0.02 0.02 for both pipes. Express your answers in 3 decimal places.
A ball with mass m kg is thrown upward with initial velocity 23 m/s from the roof of a building 25 m high. Neglect air resistance. Use g=9.8 m/s2. Round your answers to one decimal place. (a) Find the maximum height above the ground that the ball reaches. (b) Assuming that the ball misses the building on the way down, find the time that it hits the ground.
Subject : Fluid mechanics Please give me right answer according to the question. A differential manometer containing mercury is attached from the base of the inlet to the throat and to the base of the outlet. Calculate the deflection of mercury in each tube if the head lost from the inlet to the throat is 10% of the velocity in the throat and from the throat to the outlet is 30% of the velocity head in the throat.
A cylindrical tank is having hemispherical base. The height of cylindrical portion is 4 m and the diameter is 3 m. At the bottom of this tank an orifice of diameter of 300 mm is fitted. Find the time required to completely emptying the tank. Take Cd= 0.60. a. 127 seconds b. 175 seconds c. 145 seconds d. 217 seconds
Calculate the capillary effect in millimeters in a glass tube of 4mm diameter, when immersed in Water Mercury the temperature of the liquid is 200C in contact with air are 0.073575 N/m and 0.51 N/m respectively. The angle of contact for water is zero and that for mercury is 1300. Take density of water at 200C as equal to 998 kg/m3. Explain the ways of describing the fluid motion
A cylindrical tank is having hemispherical base. The height of cylindrical portion is 4 m and the diameter is 3 m. At the bottom of this tank an orifice of diameter of 300 mm is fitted. Find the time required to completely emptying the tank. Take Cd= 0.60. Answers: a.145 seconds b.127 seconds c.217 seconds d.175 seconds
Speed measurement is made with a pitot tube by connecting a mercury manometer to a vertical pipeline through which water is transmitted. If the deviation in the manometer column is 15 cm, calculate the speed of the water in the pipe.?mercury = 13560 ???3, ?water = 1000 ???3 (figure in picture) #fluidmechanics
1. In calibrating a 10-mL pipet, a measured volume of water was transferred to a tared flask and weighed, yielding a mass of 9.9814 g. (a) Calculate, with and without correcting for buoyancy, the volume of water delivered by the pipet. Assume that the density of water is 0.99707 g/cm3 and that the density of the weights is 8.40 g/cm3. (b) What are the absolute and relative errors introduced by failing to account for the effect of buoyancy? Is this a significant source of determinate error for the calibration of a pipet? Explain. 2. Repeat the questions in problem 1 for the case when a mass of 0.2500 g is measured for a solid that has a density of 2.50 g/cm3. 3. Is the failure to correct for buoyancy a constant or proportional source of determinate error?