Find the velocity (m/s) at which test should be run in a wind tunnel on a model wing of 11 cm chord in order that RN. shall be the same as for a wing with a 1.16 m chord at 41.4 m/s. Air under standard conditions in both cases. Round-off answer to the nearest hundredths.

Find the velocity (m/s) at which test should be run in a wind tunnel on a model wing of 11 cm chord in order that RN. shall be the same as for a wing with a 1.16 m chord at 41.4 m/s. Air under standard conditions in both cases. Round-off answer to the nearest hundredths.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Related questions

Q: The 113-lb force P is applied to the 250-lb crate, which is stationary before the force is applied.…

A: GivenP=113 lbm=250lbμs=0.41μk=0.32

Q: 4° 17° 1.2 m 71 kg 0.5 m A 17⁰

A: Given-Information:- Wedge Angle, θ1 = 17°Mass, m = 71 kgCo-efficient, μ = 0.38Length, L = 1.2…

Q: Find the force in member AB 2kN B

A: Given

Q: Q5. As shown in the image below, the freight cars A and B are approaching each other, and they have…

Q: PROBLEM NO. 6 Determine the force in each cable if F = 500 lb. B. -2 ft X 3 ft 1 ft D 3 ft 2 ft 6 ft…

Q: Water at 21 °C flows downward in a pipe at 0 0.53 radians inclination as shown in the figure. The…

Q: A truck experiencing drag is able to reach a maximum velocity of v₁ = 30.5 m/s. It has…

A: Given:Maximum velocity of truck for area A1=1.6 m2, v1=30.5 m/sDrag coefficient for A1=1.6 m2,…

Q: Q9. A 19-kg box was thrown onto a 36-kg cart with a speed of 5 m/s in the as shown. The cart was…

Q: Q6. As shown in the image below, the spring (with spring constant k = 2.4 kN/m) is fixed to block A,…

Q: The spring has a stiffness k = 750 N/m and an unstretched length of 50 cm. A 2 kg block is given a…

Q: At the instant shown, 0 = 60°, and rod AB is subjected to a deceleration a = 15 m/s² when the…

Q: The 1.5-in diameter solid steel shaft is simply supported at the ends. Two Pulleys are keyed to the…

Q: a simple beam AB shown supports a concentrated load P =200lbs. at point C (MID SPAN) Determine the…

A: Dear student, please find the attached solution.

Q: Q4. As shown in the image below, the freight cars A and B are approaching each other, and they have…

Q: shown in Figure 4. Columns A and B, both with a diameter of X12 mm are made of steel, and column C…

Q: A hockey puck of mass 162 grams slides toward Brett with a velocity of -15 meters per second. Brett…

Q: Air at 0° C and 95% relative humidity has to be heated and humidified to 25° C and 40% relative…

A: Given: State 1 Dru Bulb Temperature Tdb1=0oC Relative Humidity RH1=95% State 1 Dru Bulb…

Q: The figure below shows a vapor power cycle that provides process heat and produces power. The steam…

Q: A piston of double reciprocating pump running at 60 rpm to transport oil of 890 kg/m³. The pump has…

A: Given: The pump speed, N = 60 rpm The density of oil, ρ = 890 kg/m³ The stroke length of pump, L =…

Q: In the condenser of a thermoelectric plant, steam will be condensed at a temperature of 50°C by…

A: The principle of heat balance is used to solve the problem that is heat absorbed by the lake water…

Q: Draw a different configuration, and make it a diagram similar to Fig. 3. Specify each mass and angle…

Q: Consider a piston/cylinder assembly with a cross sectional area of 0.15 m2 that has compressed a…

A: Write the given data. A=0.15 m2P=180 kPaP0=110 kPa

Q: 2. 20 mm 140 mm 100 mm Determine the moments centroidal x and y axes. yo Xo 20 mm 20 mm 100 mm of…

Q: Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition.…

Q: Link OB is 20 mm wide and 10 mm thick and is made from low-carbon steel with Sy= 200 MPa. The pin…

Q: Determine the force P required to force the 12° wedge under the 99-kg uniform crate which rests…

Q: 13.3 Given the following information, and the Instron curve below for an axial stress experiment…

A: given; elastic modulus(E)=40MPaelongation at break(ε)=2.25initial length(l0)=1.5cmcross sectional…

Q: Consider a person standing in a room maintained at 20°C at all times. The inner surfaces of the…

Q: How do you determine W(input)?

A: Coefficient of performance of reversible heat pump is defined as COPR,HP=THTH-TL…

Q: Find the moment about A, B, & C, where AB = AD = 19 m, F₁1= 3 N, F₂ = 7 N, F3 = 11 N & F4 = 19 N.…

Q: Q1. Match the following principles to their respective descriptions: Usually applied to a short…

A: 1.Principle of work and energy - Applied to specific situations when only conservative forces do…

Q: If the coefficient of friction between the steel wedge and the moist fibers of the newly cut stump…

A: This question is related to the friction angle. Friction angle is defined as the resultant force…

Q: ., In a certain experiment, cylindrical samples of diameter 4 cm and length 7 cm are used (see Fig.…

Q: An aircraft deigned for supersonic flight utilises a delta wing, as shown. Using the values given in…

A: To find wing span of aircraft

Q: A particle moves along the x-axis with the velocity history shown. If the particle is at the…

Q: A refrigeration system is to cool bread loaves with an average mass of 390 g from 30°C to -10°C at a…

Q: ⒸL'avionnaire 30 in 0 1 KIP T. 2 ·20 in--20in- 1 KIP ↑ O D G 1KIP For the wing truss shown in the…

A: Given: A=200in2 To find: σ2,σ11,σ6,σ3,σ13 and σ7

Q: The driver of a car, which is initially at rest at the top A of the grade, releases the brakes and…

Q: In your own words, answer the following questions: 1. What is the dew-point temperature? 2. How does…

A: 1) Dew point temperature is the temperature at a particular pressure at which the water vapour…

Q: Problem 8.11 Chlorine Gas Chlorine gas is to be heated from 110.0°C to 180.0°C Calculate the heat…

Q: Steam flows steadily through a turbine at a rate of 45,000 lbm/h. It enters at 1000 psi and 900°F…

A: Given data:- Steam flows rate = 45,000 lbm/h=5.67 Kg/s It enters at 1000 psi and 900 °F and leaves…

Q: Compute the moment of inertia of the mallet about the O-O axis. The mass of the head is 0.8 kg, and…

A: Given data as per question Mass of head, M=0.8 kg Mass of handle, m=0.5 kg

Q: 6. 328 www 7-400 B

Q: A step test of a transducer shows a signal having a damped oscillation decayin If the period of…

A: Given data as per question Period of oscillation , T=0.577 ms

Q: The 568-N force is applied to the 97-kg block, which is stationary before the force is applied.…

Q: Required information Problem 09.034 - Ideal Otto Cycle with Variable Specific Heats - DEPENDENT…

A: givenr=8P1=95kPaT1=27oC=27+273=300KQadd=760 kJ/kgR=0.287 kJ/kgK

Q: 1. A 240 mm dia. steam pipe, 200 m long is covered with 50 mm of high temperature insulation of…

A: Given data: diameter of piped=240 mmlength of pipel=200 mthickness of insulatort=50 mminner surface…

Q: Determine the moment of inertia about the neutral axis.

Q: Q3. Two blocks, A and B, are connected using the cable and pulley system as shown in image below.…

Question

100%

Find the velocity (m/s) at which test should be
run in a wind tunnel on a model wing of 11 cm
chord in order that RN, shall be the same as for
a wing with a 1.16 m chord at 41.4 m/s. Air
under standard conditions in both cases.
Round-off answer to the nearest hundredths.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Ko

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

When a sphere falls freely through a homogeneous fluid, it reaches a terminal velocity at which the weight of the sphere is balanced by the buoyant force and the frictional resistance of the fluid. Make a dimensional analysis of this problem and indicate how experimental data for this problem could be correlated. Neglect compressibility effects and the influence of surface roughness.
Here, a 1:10 scale prototype of a propeller on a ship is to be tested in a water channel. What would the rotating speed of the model be if the rotational speed of the p propeller is 2000 rpm, and if: (a) the Froude number governs the model-prototype similarity(b) Reynolds number governs the similarity
A one-fiftieth-scale model of a military airplane is tested at1020 m/s in a wind tunnel at sea-level conditions. Themodel wing area is 180 cm 2 . The angle of attack is 3 ° . If themeasured model lift is 860 N, what is the prototype lift,using Mach number scaling, when it flies at 10,000 m standardaltitude under dynamically similar conditions? Note:Be careful with the area scaling.
A 1:20 scaled-down model of a hydrofoil is tested in a water channel, at a velocity of 0.179 m/s. At this velocity, a drag force of 2.2 N is measured. Determine the drag force of the original hydrofoil, at a velocity of 0.8 m/s.
Derive two dimensionless parameters for the shear stress at the pipe wall when an incompressible fluid flows through a pipe under pressure. In the dimensional analysis, use the following significant parameters: pipe diameter, flow velocity, viscosity of the fluid and density of the fluid. Solve the problem on white A4 size paper. Show all the calculation steps.
The time t d to drain a liquid from a hole in the bottom of atank is a function of the hole diameter d , the initial fluidvolume y 0 , the initial liquid depth h 0 , and the density ρ andviscosity μ of the fluid. Rewrite this relation as a dimensionlessfunction, using Ipsen’s method.
Q.10. To predict the drag on an aircraft at a flight speed of 150 m/s, where the condition of air is such that the local speed of sound is 310 m/s, a pressurized low temperature tunnel is used. Density, viscosity and local sonic velocity at tunnel condition are 7.5 kg/m³, 1.22 x 10-5 Ns/m² and 290 m/s. Determine the flow velocity and the scale of the model. Assume full dynamic similarity should be maintained. Density and viscosity at the operating conditions are 1.2 kg/m³ and 1.8 x 10 Ns/m².
A dam 75 ft wide, with a nominal flow rate of 260 ft 3 , is tobe studied with a scale model 3 ft wide, using Froude scaling.( a ) What is the expected flow rate for the model?( b ) What is the danger of only using Froude scaling for thistest? ( c ) Derive a formula for a force on the model as comparedto a force on the prototype.
Fluid mechanics (Subject) Write legibly and sole neatly, show diagrams A surface vessel is 156 m long and moves at a velocity of 6.83 m/s. Determine the velocity of a geometrically similar model 2.44 m long be tested.a. velocity : ____________________ m/s
A tidal estuary is dominated by the semidiurnal lunar tide,with a period of 12.42 h. If a 1 : 500 model of the estuary istested, what should be the model tidal period?( a ) 4.0 s, ( b ) 1.5 min, ( c ) 17 min, ( d ) 33 min, ( e ) 64 min
Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the wind speed V, the air density ρ, the acceleration of gravity g, the length of the banner L and the “area density” of the flag material ρA (with dimensions of ML-2 ). In order to estimate the flutter frequency of a large banner with L = 40 ft in a V = 30 ft/s wind, a small banner with L = 4 ft is to be tested in a wind tunnel. (a) What is the area density of the small banner when the large banner has area density of 0.006 slugs/ft2? (b) What should the wind tunnel velocity be to test the small model? (c) It has been shown that the small banner flutters at 6 s-1 when the same area density and wind tunnel velocity are used in parts (a) and (b). In this case, what is the fluttering frequency of the large banner?
Books on porous media and atomization claim that the viscosityμ and surface tension Y of a fl uid can be combinedwith a characteristic velocity U to form an important dimensionlessparameter. ( a ) Verify that this is so. ( b ) Evaluatethis parameter for water at 20°C and a velocity of3.5 cm/s. Note: You get extra credit if you know the nameof this parameter.