A 90m by 90m lot is to be divided into 9 equal square sections. The elevations of the ground surface at each corner of the squaresection are as follows:A=7.3m E=6.7m l=8.3m M=8.5mB=8.3m F=8.2m J=8m N=8.1mC=6.8m G=8.7m K=6.3m O=8.8mD=8.1m H=7.8m L=7.2m P=7.5mFind the volume to be excavated if the ground surface is to be leveled to elevation 5m.Round your answer to 3 decimal places.

Givendata: The elevations of the ground surface at each corner of the square section are given as:…

Answered: Find the volume to be excavated if the…

Engineering

Civil Engineering

Find the volume to be excavated if the ground surface is to be leveled to elevation 5m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The degree of a circular curve of radius 1719 m is approximately equal to 1° O 10° O 100° O None of…

A: Ans :Option 1(1degree)

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads…

Q: Determine the allowable (ASD) tensile strength (kN) of the tension member shown. while tho ulti

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

Q: A W 250 x 49 steel column 6.0m long must support an axial load of 140kN plus an eccentric load p…

Q: meters per second. If the angle of inclination is 23.6° and coefficient of kinetic friction, u =…

Q: For the Soil profile given below, determine the net allowable bearing capacity of the isolated…

A: Ultimate Bearing capacityqu : The gross pressure at the base of the foundation at which the soil…

Q: and moment diagrams for the he location of maximum moment. 300 N/m 300 N m

Q: An equal tangent vertical curve is intended to connect grades of 3.1% and -0.8%. If this curve is to…

Q: Prepare a manpower safety program of a construction of three (3) storey residential building.

A: What is Manpower Safety? Is committed to providing a safe and healthy working environment for its…

Q: Block A and B are homogeneous with 20 kg and 25 Kg mass respectively. The system is subjected to the…

A: Determine whether the two block are in a static condition or moving.

Q: rotate command Rotates --objects around new angle O around a base point. O around new direction

A: Option B Around a base point

Q: Prepare a simple drawing for your explanation. 4. What parameters characterize whether a flow is…

Q: 1. A proposed road bend along a highway construction project is to be laid out such that it will be…

A: Circular curve Intersecting straight lines are joined with circular curves (or tangents). The…

Q: A cross section of a beam is shown. For any moment M, which surface of the cross section will have…

Q: . What is the vertical reaction component at the hinge? See figure 4 b. Find the total number of…

A: Here a truss is given with a hinge at end A and a roller at end L. Hence we need to find out the…

Q: CALCLULATE THE FEM OF THE FOLLOWING USING THREE MOMENT EQUATION.

A: Calculation of FEM using three moment equation

Q: An equal tangent vertical curve is intended to connect grades of 0.9% and -2.7%. If this curve is to…

Q: as pin-ended support at A and roller supp onstruct the shear and moment diagrams alyze the location…

Q: A and rol near and moment di tion of maximum r

Q: Example 5.2. The flexible, inextensible, and gentile cable is suspended between Ewo absolutely rigid…

Q: a) What are the phase shifts? b) What is the directivity of the array?

Q: 3. Use the given table below and the technique of coordinates to compute the traverse area and plot…

A: The data is given in order to find the area we will use concept of latitude and departures.

Q: Determine the force exerted by a 25 mm jet against a fixed vertical wall if the discharge of the jet…

Q: S13. A rectangular steel beam, 2 in. wide by 3 in. deep, is loaded as shown in Fig. P-513. Determine…

Q: he lower ends of the three bars as hown in figure 5 are at the same evel before the uniform rigid…

Q: A beam has pin-ended support at A and roller support at B as shown in Figure 3 (a) Construct the…

A: The location of maximum moment can be found by equating the shear equation to zero and find out the…

Q: A beam has pin-ended support at A and roller support at B as shown in Figure (a) Construct the shear…

A: A beam is given as shown in the figure above, where UDL of 300N/m is acting and moment of 300N.m is…

Q: (c) Weathering is a common phenomenon that occurs naturally to change rock to become a stable…

A: Solution- Soil formation from rock:- The Soil is generated by a process known as rock weathering. It…

Q: Out of the diverse specializations in the Civil Engineering profession, which one are you most…

A: In these question reason for choosing a specific specialization is asked

Q: Two tangents intersect at an angle of 46°40' are to be connected by a reversed curved. The tangent…

Q: 524. A beam with an S380 X 74 section carries a total uniformly distributed load of 3W and a…

A: Determine value of W ?

Q: A cantilever beam, 53 mm wide by 153 mm high and 6 m long, carries a load that varies uniformly from…

A: Given: Cantilever beam with uniformly varying load Dimensions of beam To find: Magnitude and…

Q: 2. Determine the spacing of vertical stirrups near the left support of the beam loaded as shown in…

A: given , bw=290mm d=560mm f'c=24MPa Fyt=275Mpa PD=80kN PL=110kN WD=20kN/m WL=28kn/m To determine The…

Q: A circular curve of 500m radius is to be laid to connect two straights APB and CQB intersecting at…

Q: prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform…

Q: what The characteristics of cast iron which make it a valuable material for engineering…

A: The main characteristics of cast iron which makes it a valuable meterial for engineering purposes is…

Q: reinforced concrete beam has a width of 300mm and an effective depth of 600mm. Compressive…

Q: A beam has pin-ended support at A and roller support at B as shown in Figure 3. (a) Construct the…

A: A loaded beam is given and it has been asked to determine shear force and Bending moment diagram.…

Q: 1. A proposed road bend along a highway construction project is to be laid out such that it will be…

A: Stationing of V = 12+340

Q: pin-ended support at A and roller support at B as shown in Figure 3. Construct the shear and moment…

Q: A circular curve of 500m radius is to be laid to connect two straights APB and CQB intersecting at…

Q: The given overhanging beam is loaded as shown. Use E = 10 GPa and I = 1.5 x 10^6 mm^4 Determine the…

Q: A beam has pin-ended support at A and roller support at B as shown in Figure 3. (a) Construct the…

A: A loaded beam is given and it has been asked to determine shear force and bending moment. Please…

Q: Determine the practical stopping distance (ft) for a highway with a design speed limit of 65mph.…

A: Given: V = 65mph, G = -4.99%

Q: abnormal time readings are omitted?

A: If abnormal time readings are omitted, effects on the standard time are 1. The standard time will…

Q: NEED ASAP Differentiate and discuss the Intellectual Property Rights, Fair Use and Creative Commons

A: Copyrighted works, trademarks, patents, geographical indications, and industrial design, are all…

Q: 2. Draw the shear and moment diagram of the loaded beam shown in the figure. Determine the Vmax and…

Q: Two tangents that intersect at an angle of 44°36' are to be connected by a compound curve. The…

Q: 3C. A 100-N block on a rough 300-incline is acted upon by a force P as shown causing it to…

Question

A 90m by 90m lot is to be divided into 9 equal square sections. The elevations of the ground surface at each corner of the square
section are as follows:
A=7.3m E=6.7m l=8.3m M=8.5m
B=8.3m F=8.2m J=8m N=8.1m
C=6.8m G=8.7m K=6.3m O=8.8m
D=8.1m H=7.8m L=7.2m P=7.5m
Find the volume to be excavated if the ground surface is to be leveled to elevation 5m.
Round your answer to 3 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 90m by 90m lot is to be divided into 9 equal square sections. The elevations of the ground surface at each corner of the square section are as follows: A=7.3m E=6.7m I=8.3m M=8.5m B=8.3m F=8.2m J=8m N=8.1m C=6.8m G=8.7m K=6.3m O=8.8m D=8.1m H=7.8m L=7.2m P=7.5m Find the volume to be excavated if the ground surface is to be leveled to elevation 5m.
Compute the area enclosed within polygon ABDFGA of Figure given below using triangles.
The areas of cut of two irregular sections 60 m apart are 32 m^2 and 68 m^2 respectively. The base width is 8 m, with a sideslope of 1:1. Find the volume using end area method in cubic meter.
Two triangles are similar. Triangle 1 has side a = 15 and side b = 8. Triangle2 has side B = 30. How long is side A of triangle 2?
The areas of cut of two irregular sections 60 m apart are 32 m2 and 68 m2 respectively. The base width is 8 m. with a side slope of 1:1. Find the volume using end area method.
32. The centerline of a proposed road having a bearing of N 45° E passes through the diagonal square lot AHIG having sides of 60 m x 60 m. if the area occupied by the proposed road is equal to 1200 m2. Compute the width of the road.
Determine the difference between the elevations of Sta 6 and Sta 5, in meters, using the following notes:
A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground surface is to be leveled to elevation 10m. The elevations of the ground surface at each corner are as follows: A = 17.9m B = 19.1m C = 18.3m D = 15.9m E = 19.2m F = 19.7m G = 20.2m H = 19.7m I = 17.4m J = 16.4m K = 17.9m L = 17.2m M = 17.4m N = 18.7m O = 18.4m P = 19.6m Round your answer to 3 decimal places.
A triangular corner lot has perpendicular sides of lengths 120m and 60m. Find the dimensions of the largest rectangular building that can be constructed on the lot with sides parallel to the streets.
The area bounded by the waterline of a reservoir is determined using a planimeter. The distances from 1-2, 2-3, 3-4, 4-5, are 20m, 40m, 30m, and 30m respectively. A1=0 sqm, A2 = 208 sqm, A3 = 315 sqm, A4 = 314 sqm, and A5 = 0 sqm. Determine a. Volume using end area method b. What is the cross sectional area in the midsection of the sections 1 and 2? c. what is the difference of capacity of the reservoir using end area and prismoidal formula
A 120mx120m lot is divided into 9 equal sections. Find the volume (m3) to be excavated if the ground surface is to be leveled to elevation 10m. The elevations of the ground surface at each corner are as follows: A = 17.1m B = 19.2m C = 18.8m D = 19.2m E = 18.3m F = 19.6m G = 18.9m H = 17.6m I = 18.1m J = 15.2m K = 16.7m L = 16.2m M = 18.7m N = 16.4m O = 19.2m P = 17.5m
given a = 41 degrees, a = 3.3 and b = 5.4, how many triangles can be formed? a. 2 b. 1 c. insufficient data d. 0