Project 2:Fixed/built-in or encastré beams are usually used in structure due to their high stability and performance inresisting shear stress and bending moment. Your role in building and construction company is to analyse theshear force and bending moment in order to provide better design of such beams under variety of loads. Yourmanager asked you to provide a complete analysis as well as to deliver a report including your designrecommendations.100 KN/m150 kNz (m)5710Figure.2: Encastré beam under variety of loadsYour tasks are as follows:1- Construct free-body diagram (FBD) to show the reaction forces and moments, equivalent force of thedistributed load.., knowing that the upward reaction force on left side is 250 kN and the reaction momentis clockwise with a value of 1500 kN.m.2- Show FBD for each required section/cutting, include the internal forces and moments.3- Write the distribution functions of the shear force and bending moment for each cut in the beam.

FBD, a Free body diagram of a body or a section shows all the forces or reactions acting upon the…

Fixed/built-in or encastré beams are usually used in structure due to their high stability and performance in resisting shear stress and bending moment. Your role in building and construction company is to analyse the shear force and bending moment in order to provide better design of such beams under variety of loads. Your manager asked you to provide a complete analysis as well as to deliver a report including your design recommendations. 100 kNim 150 kN z (m) 5 7 10 Figure.2: Encastré beam under variety of loads Your tasks are as follows: 1- Construct free-body diagram (FBD) to show the reaction forces and moments, equivalent force of the distributed load.., knowing that the upward reaction force on left side is 250 kN and the reaction moment is clockwise with a value of 1500 kN. m. 2- Show FBD for each required section/cutting, include the internal forces and moments. 3- Write the distribution functions of the shear force and bending moment for each cut in the beam.

Fixed/built-in or encastré beams are usually used in structure due to their high stability and performance in resisting shear stress and bending moment. Your role in building and construction company is to analyse the shear force and bending moment in order to provide better design of such beams under variety of loads. Your manager asked you to provide a complete analysis as well as to deliver a report including your design recommendations. 100 kNim 150 kN z (m) 5 7 10 Figure.2: Encastré beam under variety of loads Your tasks are as follows: 1- Construct free-body diagram (FBD) to show the reaction forces and moments, equivalent force of the distributed load.., knowing that the upward reaction force on left side is 250 kN and the reaction moment is clockwise with a value of 1500 kN. m. 2- Show FBD for each required section/cutting, include the internal forces and moments. 3- Write the distribution functions of the shear force and bending moment for each cut in the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A timber beam shown in the figure is made up of Kamagong (50% stress grade). Use LRFD. All the given loads shown in the figure below are unfactored service loadings only, it does not include the weight of the beam itself. The allowable deflection for beams is L/240, what is the allowable deflection in mm.?
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER From a 12.00 meter bridge span, a truck and trailer combination crosses with an axle loads of 10, 20, and 30 kN separated respectively by distances of 3 and 5m. What will be the nearest moment with reference from the left of the 10kN loading? a. 45.00 kN b. 25.75 kN c. 37.50 kN d. 61.25 kN.m
Recently, they have had some problems with their steel and look into some failures. The most probable strength of a steel beam is given by 24Y ―0.05 kips where Y is the number of cycles. This value is known to be 25% with 90% confidence.a) How many cycles will elapse before the beam loses 20% of its strength?b) Suppose the cyclic load on the beam is 10 kips. How many cycles will occur before the probability of failure reaches 10%? Assume this can be described by a lognormal distribution.
A timber beam shown in the figure is made up of Kamagong (50% stress grade). Use LRFD. All the given loads shown in the figure below are unfactored service loadings only, it does not include the weight of the beam itself. What is the moment of inertia of the beam in mm4 with respect to x-axis?
A wire 4m long is stretched horizontally between points A and B 4m apart. A load W placed at the center of the wire produces a sag of 53.4mm,a. If the wire is 25mm2in cross-section and the Young’s modulus is 200GPa, what is the magnitude of load W?b. If the load was reduced by 40%, what will be the sag?
Please answer in 30 minutes. STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
What is the value of the long term deflection for the double reinforced beam having a base of 250 mm, d of 400 mm, As = 3000 mm^2, As' = 1000 mm^2. If the computed value of deflection deadload = 5.50 mm, deflection live load = 10.00 mm, deflection sustained live load = 7.00 mm. The long term deflection to be considered is 8 years.
A spiral column carries a dead load of 1070 kN and a live load of 980 kN. If fc' = 27.50 MPa Fy = 413.50 MPa. Use U = 1.2D + 1.6L, Ф = 0.65, ρ = 0.01 1. Which of the following gives the value of the diameter of spiral column. a. 440 mm b. 420 mm c. 450 mm d. 510 mm 2. Which bar size will provide least number of pieces allowed?. a. 16 mm b. 22 mm c. 20 mm d. 25 mm 3. Which of the following gives the possible spacing of the 10 mm0 spirals. a. 30 mm b. 40 mm c. 60 mm d. 60 mm
The dimensions, reinforcement and material of a beam produced in a poorly controlled construction site are given as C20, S420, Es = 2 × 105 N / mm2. The design on the beam affects the distributed load. Calculate the maximum load X load that the beam can safely carry, how many kN / m. The section view of the beam is given below. Cover margin is 30 mm.
strength of materials... answer only A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 34 mm from the top of the of the beam on a section 1.66 m from A if P = 5381 N, W = 2349 N/m, a = 1.31 m, b = 2.12 m, c = 1.27 m, L = 72 mm and h = 239 mm. Round off the final answer to two decimal places.
A column in a building is subjected to a compressive load from the following sources:10 kips from dead load6 kips from roof live load7 kips from snow9 kips from wind8 kips from 4 inches of rain accumulated on the roofa. If load and resistance factor design is used, determine the factored load (requiredstrength) to be used in the design of the column. Which AISC load combinationcontrols?b. What is the required design strength of the column?c. What is the required nominal strength of the column for a resistance factor ∅ of0.90?d. If allowable strength design is used, determine the required load capacity(required strength) to be used in the design of the column. Which AISC loadcombination controls?e. What is the required nominal strength of the column for a safety factor Ω of 1.67?Note: All given loads are service loads.
In the problem shown in the picture it is already solved Determine the design strength of an ASTM A992 W14 x 132 that is part of a braced frame. Assume that the physical length L = 30 ft., the ends are pinned and the 18 column is braced at the ends only for the X-X axis and braced at the ends and mid-height for the Y-Y axis. The question is Why is Sample Problem #4 a non-slender member? Is it desirable? Why?