For a composite Wall ABC, which is composed of 10 cm Wall A (k=0.40Wlm?.C), 2cm, Wall B (k=0.03W/ m² .C), and 6 cm Wall C (k=0.30W/ m? .C), has a temperature of T= 21°C at the outer surface of Wall A and a temperature of T=90°C at the exposed surface of Wall C. Determine the fllowing: a) The temperature between WallI B and Wall C b) Explain the concepts/principles that were considered and the factors that affected the condition of the above mentioned items (a & b).

For a composite Wall ABC, which is composed of 10 cm Wall A (k=0.40Wlm?.C), 2cm, Wall B (k=0.03W/ m² .C), and 6 cm Wall C (k=0.30W/ m? .C), has a temperature of T= 21°C at the outer surface of Wall A and a temperature of T=90°C at the exposed surface of Wall C. Determine the fllowing: a) The temperature between WallI B and Wall C b) Explain the concepts/principles that were considered and the factors that affected the condition of the above mentioned items (a & b).

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.17P: 3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient...

See similar textbooks

Similar questions

The composite wall which is composed of 10 cm brick (k=0.40 W/m2-C), 2 cm cellotex (k=0.03 W/m2- OC), and 6 cm (k=0.30 W/m2-OC),has an outer (brick) temperature T=23 OC and an inner (plaster)temperature T=90 OC. Find the temperature between the cellotex andplaster in OC.
Design a solar chimney to cover 75% of total heating losses, where U value for the chimney=0.5 W/m2.K and the total wall area of the spaces equal 70m2 and the temperature outside are 5oC at night and 8oC at day and the temperature for the interior is 24 oC.
A 3 – m high and 5 – m wide wall consists of 16 – cm by 22 – cm cross section horizontalbricks (k = 0.72 W/m – K) separated by 3 – cm thick plaster layers (k = 0.22 W/m – K).There are also 2 – cm thick plaster layers on each side of the brick and a 3 – cm thickrigid foam (k = 0.026 W/m – K) on the inner side of the wall. The indoor and outdoortemperatures are 20 oC and -10 oC, respectively and the convection heat transfercoefficients on the inner and outer sides are h1 = 10 W/m2 – K and h2 = 25 W/m2 – K,respectively. Assuming one – dimensional heat transfer and disregarding radiation,determine the rate of heat transfer through the wall.
The concrete slab of a basement is 11 m long, 8 m wide, and 0.20 m thick. During the winter, temperatures are nominally 17°C and 10°C at the top and bottom surfaces, respectively. If the concrete has a thermal conductivity of 1.4 W/m · K, what is the rate of heat loss through the slab? If the basement is heated by a gas furnace operating at an efficiency of ηf = 0.90 and natural gas is priced at Cg = $0.02/MJ, what is the daily cost of the heat loss?
A 2.54-cm. steel bolt is used to clamp two aluminum (2014-T6, HT aged) plates together as shown by Fig. Problem 5. The aluminum plates have a total thickness of 08 cm. and an equivalent diameter of 5.08 cm. The bolt is heated to a temperature of 93.33 oC, the inserted in the aluminum plates, which are at 26.7 oC, and tightened so as to have a tensile tightening stress of 207 MPa in the unthreaded shank while steel at 93.33 oC. What is the tensile stress in the bolt after assembly has cooled to 26.7 oC? The deformations are elastic.
A cylindrical body having 10 cm diameter and lenth of 30 cm passes through a heat treatment furnace which is 6 m in length. The body must reach a temperature of 800°C before it comes out of the furnace. The furnace gas is at 1250°C and body initial temperature is 90°C. How much time it will take to attain the required temperature ? Take h = 100 W/m² °C. Take K(steel) = 40 W/m°C and a (thermal diffusivity of steel) = 1.16 x 10-5 m²/s.
The steel rod (k=43 W/m.K) has 0.3 m is located between two walls seen in figure. The left and right sides of the walls are maintained at TB=221,01°C and TL=86,29°C, respectively. Air is flowing across the rod with a heat transfer coefficient of 17 W/m2.K and 66,79°C. Determine the rate of heat loss [W] from the rod?
The 5-mm-thick bottom of a 200-mm-diameter pan may be made from aluminum (k= 240 W/m·K) or copper (k= 390 W/m·K). When used to boil water, the surface of the bottom exposed to the water is nominally at 110°C and heat is transferred from the stove to the pan at a rate of 1200 W. What is the temperature of the surface in contact with the stove for each of the two materials?Aluminum:T= _____ °CCopper:T= _____ °C
A 10-cm diameter pipe is covered by 2 layers of lagging. The insidelayer is 4 cm thick and has a coefficient of thermal conductivity of 0.08W/m-K. The outside layer is 3cm thick and has a coefficient of thermalconductivity of 0.15 W/m-K. The steam main conveys steam apressure of 1.7 MPa with 25 C superheat. The outside temperature ofthe lagging is 27 C. If the steam main is 30 m long, determine theinterface temperature of the lagging and overall coefficient of heattransfer based on outside area.
Two metal rods are being heated in an oven with uniformambient temperature of 1000°C and convection heattransfer coefficient of 25 W/m2·K. Rod A is made of aluminum(r = 2702 kg/m3, cp = 903 J/kg·K, and k = 237 W/m·K)and rod B is made of stainless steel (r = 8238 kg/m3, cp =468 J/kg·K, and k = 13.4 W/m·K). Both rods have diameterof 25 mm and length of 1 m. If the initial temperature of bothrods is 15°C, determine the average temperatures of both rodsafter 5 min elapsed time.
Convective heat transfer coefficient is 15 W/(m*K), surface area of the fin is 2 m^2, the temperature at the base is 70 C and the ambient temperature is 20 C. Determine the fin efficiency if the actual heat transfer rate from the fin is 500 W?
A domestic refrigerator with inner dimensions of 0,7 m by 0,7 m at the base and height 1m was designed to maintain a set temperature of 6 degrees Celsius. The bodies consist of two 10 mm thick layers of Aluminum (k=225W/mK) separated by a 30 mm polyurethane insulation (k=0,028W/mK). If the average convection heat transfer coefficient at the inner and outer surfaces are 116W/m²K and 14,5W/m²K respectively. Calculate : 1)The individual resistance (R) for each thermal layer, as well as for the refrigerator 2)The steady rate of heat transfer from the interior to maintain the specified temperature in the kitchen at 25 degrees Celsius 3)The outer surface temperature of the Aluminum 4)Sketch the sectional view of the refrigerator showing thermal circuit