For a fully developed laminar flow, the velocity profile in a circular pipe of inner radius R = 1.13 cm, in m/s is u(r) = 3(1-r2/R2). Solve for the volume flow rate in L/s. Round your answer to 2 decimal places. %3D

For a fully developed laminar flow, the velocity profile in a circular pipe of inner radius R = 1.13 cm, in m/s is u(r) = 3(1-r2/R2). Solve for the volume flow rate in L/s. Round your answer to 2 decimal places. %3D

Name: For a fully developed laminar flow, the velocity profile in a circula
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: For a fully developed laminar flow, the velocity profile in a circular pipe of inner radius R = 1.13 cm, in m/s is u(r) = 3(1-12IR2). Solve for thevolume flow rate in LUs. Round your answer to 2 decimal places.%3D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Similar questions

Oil, with ρ = 875 kg/(m^3) and ν = 2E-5 (m^2)/s flows through a 250-cm-diameter, 200-m long pipe with head loss of 9.2 m. The roughness ratio for the pipe is ε/D = 0.00025. Find the mean velocity of the oil in m/s. Round your answer to 2 decimal places.
Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 25mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Colebrook and Darcy-Weisbach Formula, determine the following:a. relative roughness of the 25mm pipeb. roughness coefficient of 75mm pipec. head loss of 50 mm pipe
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
b) Given the below conditions are given for a partially circular channel shown in Figure2.▪ Flow = uniform▪ Density, ρ = 998.0 kg/m3▪ Dynamic viscosity, μ = 1.002 x 10^-3 kg/m∙sCalculate the hydraulic radius, Reynolds number, and the type of flow.
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Determine the pressure drop over a reducer with the following conditions: Fluid density: 25 kg/m3Fluid velocity: 1.5 m/sFluid viscosity: 0.001 Pa*sInlet diameter: 0.12 mOutlet diameter: 0.019 mPipe absolute roughness: 4e-4 m Give your final answer in Pa, rounded to the nearest whole number. [Ignore entrance/exit losses and velocity loss terms]
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Discuss the similarities and contrasting features in the derivations of the following equations: Piezometric head Euler's eq Bernoulli's eq Energy eq
Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is 0.04 Pa-sec. If head loss is 5.22m, determine: a. Mean Velocity of flow (m/s) b. Type of flow c. Friction Factor d. Velocity at the centerline of pipe (m/s) e. The shear stress at the wall of the pipe (Pa)
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
For the conduction of the water there is a height difference of 38 m. The results obtained from the hydraulic calculation for three different diameters are shown in the following table Diameter, in. Total head loss, mca 8 56.5 12 37.2 16 29.1 What will be the available driving load? TRANSLATED FROM Para la conducción del agua se cuenta con un desnivel de cotas de 38 m. Los resultados obtenidos del cálculo hidráulico para tres diámetros diferentes son mostrados en la siguiente tabla: Diámetro, plgs. Pérdida de carga total, mca 8 56.5 12 37.2 16 29.1 ¿Cuál será la carga de conducción disponible?
Water flows through a pipe 25 mm in diameter at avelocity of 6 m s−1. Determine whether the flow will be laminaror turbulent assuming that the dynamic viscosity of water is 1.30× 10 −3 kgm−1s−1 and its density 1000kgm−3 . If oil of specific gravity 0.9 and dynamic viscosity 9.6 ×10−2 kg m−1s−1is pumped through the same pipe, what type of flow will occur?