For a liquid velocity u varies with y as follows U = 3y-6y² U = m/s and y is in meter for Y = 2 cm find shear stress in liquid (μ = 1 poise)
Q: Using linear interpolation determine the DBTT of a given steel with the following Charpy tests…
A: The given data is shown below:
Q: A rectangular channel of 2.5 m width is carrying a discharge of 4 m³/s. Considering that…
A: Given : Width = 2.5 m Discharge = 4 m3/s g = 9.81 m/s2 This is a problem of Fluid mechanics where we…
Q: An instrument was setup at P and angle of elevation to a vane 4 m above the foot of staff held at Q…
A: Given- At P- Angle of elevation to a vane 4 m above the foot of staff held at Q was 9 ° 30'. The…
Q: eam shown, draw influence lines for RAVE, ME VE ME, MA, and VB A 2m E 2m B Im C F 4m
A:
Q: Irrigation water is to be provided to a crop in a field to bring the moisture content of the soil…
A: Given data, Permanent wilting point = 18% Field capacity = 28% D = 0.7 m Density of soil = 1.3…
Q: 7. If a 45 cm diameter pipe pile is driven into clayey soil to a depth of 12 m. (a) what would the…
A: Given, D = 45 cm or 0.45 m L = 12 m ϕR = 30o
Q: Number of full joints (J1)
A: Stability means the structure should be in equilibrium. Stability is based on two parameters: 1.…
Q: 0.5 m -3 m- 0.5 m 175 N/m -3 m- 200 N/m What is w (N/m) & d (meter) of the support on the right to…
A:
Q: A centrifugal pump is used to move water from the lower reservoir to the upper reservoir at a rate…
A: Centrifugal Pump: A Centrifugal pump is used to transfer the water or any fluid from the lower…
Q: 2. [Ac, 0c] Use conjugate beam method. (EI is constant) 30 ft B 15 ft 15 k C
A:
Q: DA River in the Thunder Bay area experienced peak floods of 2600 ft/s and 3000 ft³/s respectively…
A: Peak floods (a) = 2600 ft3/sec Return period (a) = 15 years Peak floods (b) = 3000 ft3/sec Return…
Q: Calculate total cost per cubic yard of concrete, given the following: Concrete materials and…
A: Given, Material and batching cost = $70/cy Trucking cost = $6/cy Paver production = $120cy/hr…
Q: lease explain the derivative part better, it makes no sense to me on how the 2 came to be
A: Given:- The velocity distribution expression is given by uU=1-exp-2×yδ To determine:- The derivative…
Q: A Carnot vapor refrigeration cycle operates between thermal reservoirs at 7°C and 28°C. The working…
A:
Q: A designer is estimating the number of luminaires using the long version of the lumen method. The…
A:
Q: A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi;…
A:
Q: Situation: The tangents of a simple curve have bearings of N 20° E and N 80° E respectively. The…
A: Given : Bearings of simple curve : N 20o E and N 80o E Radius of curve = 200 m This is a problem of…
Q: Which of the ff. is false regarding compaction in a solid waste landfill? a. It extends the life…
A: Solid waste landfill- An isolated plot of land or excavation that receives household waste is known…
Q: 1,0 m * 4 m * 5 m TINININININININ NINI NININIK Dry bark clay y =18 kN/m³ PVP V I 1 I I Sa Ysat =15…
A:
Q: There is a door-shaped structure bearing force as shown in the figure below. The E of the entire…
A: ###Determination of Member End Bending moment #### Using slope deflection method
Q: H.W.11: Calculate the design bending strength for the doubly reinforced rectangular section shown…
A:
Q: write a short litrature review on buoyant or floating houses
A: This question is related to the Building construction from Civil Engineering. In this question ask…
Q: 4. A flexible foundation is shown below, determine the immediate settlement below the center of the…
A:
Q: Calculate the velocity V m/s at a pipeline cross section where the total head, H is 54.6 m, the…
A: ###Determination of Velocity in Pipe at given Section of pipe #### Using bernoulli equation##
Q: Question 2 of 3 Determine the force in each member of the loaded truss. The forces are positive if…
A:
Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…
A: Torque applied = 3650000 N-mm Outside Diameter = 75mm Inside diameter = 75 - 2 x 5 = 65mm Length of…
Q: A square footing is to be constructed as shown in the Figure below. The design load, Qdesign is…
A:
Q: I need help on this question: a) Find the value of the integration constant C4. The answer should…
A:
Q: Decide the total horizontal floor length for a structure on pervious formation based on Khosla's…
A:
Q: A hollow steel shaft with an outside diameter of 115 mm and a wall thickness of 11 mm is subjected…
A:
Q: 12. (Horton's equation for infiltration rate, J. One can use Horton's equation to estimate the…
A: Given data in question Hortons equation fc = 6.68 cm hr-1 fo = 8.81 cm hr-1 K = 1.40 hr-1 T = 30…
Q: Determine the thickness of a rigid pavement with a wheel load capacity of 54 kN, if the allowable…
A: Given data, Allowable tensile stress of concrete = 1.6 Mpa Wheel load capacity = 54 kN
Q: Calculate the R factor for an area inside that has a total annual rainfall of 180 mm using the equat…
A:
Q: Q1.: Calculate the amount of (cement+ sand+ gravel) for foundation below: If concreate grade M25 (2)…
A: Given: Section of foundation: 0.5 m x 1 m Grade of concrete: M25 (1:4:8) To find: The quantity of…
Q: Follow IS code A reinforced concrete beam has a width of 300 mm and an effective depth to tension…
A: A ) Given data : Width of beam = 300 mm Effective depth = 600 mm f'c = 30 MPa and fy = 414 MPa…
Q: What should I do if the sum of the angles are greater than 180? Should I input the discrepancy as…
A:
Q: 6. Details of a retaining wall are shown in the figure below. The unit weight of the wall material…
A:
Q: Topic: Laminar & turbulent flow Question 5 An air stream is flowing over a flat plate with a…
A: Given- Velocity u = 8 m/s, Displacement d= 0.5 mm = 0.0005 m, Density ρair = 1.2 kg/m3, It is needed…
Q: -5 m- 15 kN/m -5 m- El = constant
A:
Q: The velocity at a point on a model of an emergency spillway for a dam is 5 m/sec. If the…
A:
Q: shallow foundation
A: This question is from Geotechnical Engineering.
Q: Calculate the number of degrees of freedom' / Figure 3
A: A degree of freedom is the number of possible movements of a structural system .
Q: W₂=2rad/s A V₂ 3" 8 B Figure 1 TO INFINITY 90° TO INFINITY V F
A:
Q: Find the heat loss rate per square meter through the thermal wall of a furnace that operates at…
A: Given data, Operating temperature of furnace (T1) = 1000°C Outer surface temparature of furnace…
Q: Area by Triangle Sample Problem 1 LINE PA PB PC PD D BEARING N 41°30' W N 38°10' W S 70°20' W S…
A: Given: Line Bearing Distance PA N 41o 30' W 410.52 PB N 38o 10' W 532.18 PC S 70o 20' W…
Q: For the soil profile given below, assume that the primary consolidation settlement for the clay…
A: Given, Cα = 0.03 tp = 3 years eo = 0.70 To find : Secondary consolidation settlement
Q: Could you explain how to get the reaction A and reaction at B it is in the given datat but assume it…
A:
Q: Slope at point A and deflection at midspan. 8 kN/m Aப் 7m A 3m 000 B
A: Given Data EI = constant Find slope at A and mid span deflection. Let's solve using Double…
Q: Fig shows a brass bar having cross-sectional area of 1000 mm subjected to axial force . Find the…
A: Given data in question Loads 50 , 80 ,20 and 10 kN Lengths 0.6 , 1 and 1.2 m Elasticity modulus 100…
Q: You didn't solve the problem correctly could you resolve it and please clarify your steps the…
A:
Please solve.it .
Step by step
Solved in 2 steps
- In horizontal pipe, which of the following is constant? Pressure headElevation headVelovity head 12An incompressible fluid is flowing at steady state in the annular region (i.e., torus or ring between two concentric cylinders). The coaxial cylinders have an outside radius of R and inner radius of λR. Find:a. shear stress profile b. velocity profile c. maximum and average velocitiesPlease be clear with your soltuion. In the figure, x=25cm initially. If the pressure at m is increase by 35 KPa while maintaining the pressure at n constant. Calculate the new value of x.
- A cylindrical tank has a mean radius of 40 cm and thickness of 10 cm. It is subjected to an external pressure of 140 kg/cm2 and maximum internal pressure is 900 kg/cm2 . Determine the maximum internal tangential stress of the tank. A. 3,884.7 kg/cm2 C. 1.7684 kg/cm2 B. 4,623.6 kg/cm2 D. 2,947.5 kg/cm2A cylindrical tank has an internal pressure of 1.5Mpa. - Determine the diameter of the cylindrical tank if the strenght per meter of longitudinal joint is 480KN - Determine the diameter of cylindrical tank due to strenght of girth joint of 200KN -Determine the minimum thickness of the cylindrical tank if the stress is limited to 40Mpaa) Determine the zero-effort frame by justifying with a table asfollow Joint in equilibrium Nul stress frame .
- Consider a Boeing 787 and assume the fuselage cross-section to be circular with a diameter d=5.9m, a skin thickness t=2mm, and isotropic material properties of E=60GPa and ν=0.28. The vertical tail plane applies a torsional moment of the rear fuselage, inducing a shear flow in the rear fuselage skin. Calculate the shear stress τ in the rear fuselage skin for the assumed fuselage diameter and thickness if a torsional moment of MT=1.8⋅106N⋅m is applied. Hint:Applu q=MT/2A. Select whether the following statement is true or false: Damage tolerance is the structural ability to sustain environmental degradation to the extent that economically acceptable maintenance programs can control it.3) The kinematic viscosity of the oil filled between two concentric vertical 150 mm long cylinders is 1.5 stokes. The outer diameter of the inner cylinder is 0.2 m, and the gap between the two cylinders is 1.2 mm. The inner cylinder is rotated at 200 rpm. Determine the shear stress acting in between the cylinders if specific gravity of the oil is 0.85 and also find the force required to rotates the inner cylinder.Determine the limiting peripheral velocity of a rotating steelring if the allowable stress is 150 MPa and the mass density ofthe material is 7800 kg/m3.
- A plate 0.035mm distant from a fixed plate, moves at 80 cm/s and shear stress is 2 N/m2 to maintain this speed. Determine the fluid viscosity between the plates.At 200C, there is a gap d = 0.2 mm between the lower endof the bronze bar and the rigid slab supported by twosteel bars as shown. Neglecting the mass of the slab,determine the stress in each rod when the temperatureassembly is increased to 1000C.Block A has a mass of 100 kg and the coefficient offriction is 0.20. Determine the friction force betweenA and B.