1 For an amplifier, the input Signal power Si =3 W,Input Noise power Ni=0.04 W , Output SignalPower So = 42 W. Noise Figure (NF)= 5.83 dB.%3D(i) Calculate the noise power at the output of theamplifier in Watts due to its internal noise (Neo)alone.(ii) Calculate its equivalent Noise Temperature (Te)in deg Kelvin, if the Bandwidth is 5MHZ.marke)Noise power at the output(in Watts) due tointernal noise (Neo) (Approximated to 2 decimalplaces) =The equivalent Noise Temperature in deg Kelvin =

The noise figure is NF=5.83 dB. The noise factor (F) can be obtained in the following way:…

Answered: For an amplifier, the input Signal…

For an amplifier, the input Signal power Si =3 W, Input Noise power Ni=0.04 W , Output Signal Power So = 42 W. Noise Figure (NF)= 5.83 dB.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. For an electronic device operating at a temperature of 17°C with a bandwidth of 10 kHz, determine:a. ThermalnoisepowerinwattsanddBm.b. Rmsnoisevoltagefora100Ωinternalresistance. 2. Two resistors, 20 kΩ and 50 kΩ are at ambient temperature. Calculate for a bandwidth equal to 100 kHz, the thermal noise voltage for the tworesistors connected in parallel.
Design a Common Emitter Amplifier using Emitter-Stabilized Biased Configuration having the following specifications: . ICQ = ½ of ICsat ICsat=4mA VCEQ = ½ of VCC VC=18V VCC=28V βdc=110 and Determine RC, RE and RB (Final answer must be in 3 decimal places w/out rounding off) Draw the circuit diagram and label the different parameter values.
The equation of an angle-modulated voltage is v = 10 sin (l08t + 3 sin 104,). What form of angle modulation is this? Calculate the carrier and modulating frequencies, the modulation index and deviation, and the power dissipated in a 100-ohm resistor.
Draw the DC circuit: b)DC computations: Compute the DC collector current of each transistor. I_C 1 = ________________________ mA I_C 2= ________________________ Calculations: c)Draw the AC circuit and compute gm, r_pi for the system. g_m 1= _______________________ mA/V r_pi 1 = _______________________ kohms g_m 2= _______________________ mA/V r_pi 2 = _______________________ kohms AC circuit: Calculations: d)Compute the gain A_v=Vo/Vi at the operational band (for sufficiently high frequency) Gain = A_v = ______________________________ Computations:
Vcc=25V , Vi=35mV , RB =470kΩ , RC=2,6kΩ , RE1=470Ω , RE2=1.2kΩ , RL=16.8kΩ , β=110 Find the output voltage V0 = ? Note1=Capacitors are negligible at mid-band frequency. Note2 0 The output impedance (r0) of the transistor will be neglected.
The noise produced by a resistor is to be amplified by a noiseless amplifier having a voltage gain of 75 and a bandwidth of 100 kHz. A meter connected to the output of the amplifier reads 240 μV RMS. Assuming operation at 37°C, calculate the resistor’s resistance. In the previous problem, if the bandwidth were cut to 25 kHz, determine the expected output meter reading. A. 240 μV B. 60 μV C. 120 μV D. 75 μV
4. For an FM modulator with 40-kHz frequency deviation and a modulating-signal frequency fm= 13 kHz, determine the bandwidth (in kHz) using Carson's rule. 5. Given an FM modulator with a deviation sensitivity K1= 1.4 kHz/V and a modulating signal vm = 3.9 sin(2π1,948t), determine the peak frequency deviation in kHz. 6. The percent modulation of the sound portion of a TV signal is 73%. The maximum frequency deviation for the sound portion of the TV signal as specified by the FCC is 25 kHz. Determine the frequency deviation in kHz.
ı just need the fınal answer Since Vcc = 20 V, RS = 3 kΩ, RB = 380 kΩ, RC = 1.2 kΩ, RE = 2.2 kΩ, RL = 911 Ω and β = 90 in the circuit in the figure, find the value of the output voltage (Vo). NOTE-1: It is within the 1 kHz mid-band frequency and the capacitors are negligible at this frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected. a. 64,14 mV b. 83,88 mV c. 93,75 mV d. 74,01 mV e. 103,62 mV f. 24,67 mV g. 34,54 mV h. 49,34 mV
Given that fc(OL) = 880 Hz, AOL = 91 dB. Determine the unity gain bandwidth...
Please answer numbers 3 AND 4 ONLY asap with clear and complete explanation. Thank you! Electromagnetics (Communication Receivers) 1. what is communication receiver and explain in detail the operation. 2. Explain in detail how the design of dual-conversion receivers allow them to enhance selectivity and eliminate image problem. 3. Explain the relationship between(IF) local oscillator, and signal-frequencies mathematically and calculate any one of them, given the other two. 4.What is mixer circuits and explain in detail.
Assume that an RF amplifier’s input has a signal power of 2μW and a noise power of 323nW, what is the signal-to-noise ratio? Assume that the RF amplifier in problem number 1 has a signal-to-noise ratio of 5 at the output. Calculate the noise ratio and noise figure. Given the noise ratio calculated in problem number 2, what is its equivalent noise temperature? What is the average noise power of a device operating at temperature 75oF with a bandwidth of 33 kHz? Assuming that an oscilloscope displays a Vmax of 5.22V and Vmin of 1.33V. Calculate the percentage of modulation. Three (3) AM broadcast stations are spaced at 18 kHz, beginning at 73 kHz. Each station is allowed to transmit modulating up to 6 kHz. Compute for the upper and lower sidebands of each station and plot it in the frequency domain. Given a Vmax of 7.45V and a modulation index of 0.691, calculate for Vmin. A station is given a carrier frequency of 88 kHz. Having a modulating frequency of 12 kHz, compute for…
Assume that an RF amplifier’s input has a signal power of 2μW and a noise power of 323nW, what is the signal-to-noise ratio? Assume that the RF amplifier in problem number 1 has a signal-to-noise ratio of 5 at the output. Calculate the noise ratio and noise figure. Given the noise ratio calculated in problem number 2, what is its equivalent noise temperature? What is the average noise power of a device operating at temperature 75oF with a bandwidth of 33 kHz?