Answered: For data below the average P over an…

For data below the average P over an area by Isohyetal method is? if the area between each two stations = 100 Km ^2 (P1= 150mm, P2= 127, P3=152mm, P4= 152 mm)

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter14: Highway Surveys And Location

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: differentiate at least three (3) advantages and three (3) disadvantages of using Trapezoidal Rule…

A: Difference between the trapezoidal rule and Simpson's one third rule Advantages: Trapezoidal…

Q: 2. It is desire to measure angle AOB with the transit at 0, but due to the fact that 0 is a swamp,…

A: As Per Guidelines , I can Only solve first part.

Q: In a closed traverse, course DA was found to have a latitude of 63.78 m and a departure of 28.40 m.…

A: Given, There is a closed traverse In which The line DA latitudes and Departures are given below and…

Q: Data of a closed traverse are as follows: Compute the distance of line (5-1) a. 206.92 m b. 374.97 m…

A: Let distance 3-4 be x and distance 5-1 be y

Q: A building along the line AB makes direct measurement impossible. A point V is establlished at a…

A: Given: The length CV is 6.75 m. The length AV is 392.50 m. The length BV is 407.20 m. Consider the…

Q: The interior angles of a five-sided traverse are as follows: A= 117°30' B=96°32' C=142°54'…

A: n=5 sides To find bearing of line DE

Q: 1. Given the following tabulations are observed and calculated data for a traverse. Balance the…

Q: alculate the side widths and cross-section area of embankment having width =20m and side slope( 1/2…

A: Side Width are Given as : b1=b2+nsn-sh+h2nb2=b2+nsn+sh-b2nCross Sectional Area = 12b2s+hb1+b2-b22s

Q: a) Plot the closed traverse based on the observed data. b) Compute the area using DMD method. c)…

A: To : Plot the traverse Compute the area of traverse using DMD method Compute the area of traverse…

Q: Give at least three (3) advantages and three (3) disadvantages (for each) of using an interior angle…

A: Advantages of interior angle traverse in adjusting a given traverse Adjusting interior angle for…

Q: a table, cite and differentiate at least three (3) advantages and three (3) disadvantages of using…

A: The method of using successive stations and a transit or theodolite for measuring the horizontal…

Q: A closed traverse has the following data. Determine the corrected latitude of the line CD using…

Q: An open channel is to be designed to carry 1 m3/s at a slope of 0.0065. The channel material has n =…

Q: A transit is set up at a distance back of the zero end of a level base line 240 m. long. The base…

A: Given:- The distance at which transit is set up = 240 m The baseline being marked by stakes at…

Q: An engineer’s transit was set up at a central station O. Four surrounding points A, B, C and D were…

A: Angle AOB 63°25’ BOC 55°45’, COD, 29°15’ DOA 31°10 Most probable value of BOC is nearest to 55°45'.…

Q: Given the traverse data above, what is the LEC? Given the traverse data above, what is the precision…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Determine the Desirable Clear Zone Distance on a 3:1 sideslope. design Speed = 90 km/h sideslope…

A: Solution: Given: Design Speed = 90 km/h Sideslope ratio = 3:1 AADT = 4000 vpd Radius = 1100 m Slope…

Q: Determine the linear error of closure, relative error of closure, adjusted, latitude, departure,…

A: DMD of a line = DMD of previous line + Departure of previous line+ Departure of present line We…

Q: The following tabulated data is to be used in determining the area of traverse ABCDE by the DMD…

A: The double meridian distance of all the courses will be: DMD of AB=78.34 DMD of…

Q: Compute the closure error in closed-polygon traverse if you know the relative precision (1/12000)…

Q: cem Problem No. The following close traverse data are collected in the field by the students of GE…

Q: The following data are the cross section notes at station 12+046.58 and 12+066.58. The natural…

A: (A) A= 20.25 m2 (B) A= 12.8 m2 (C) VC-VF= 70.3 m3

Q: As a result of observing the slope with a 30m tape measure, which is 7.5mm longer than the standard…

Q: Stations 5 + 100 and 5 + 120 are stations with regular trapezoidal sections (level sections) with…

Q: Fundamentals of Surveying problem: Topographic survey conducted by SALCON shows that the centerline…

A: Consider the free body diagram;

Q: ) For a traverse having a precison ration of 1:7,024 and total distance of 352 what is the total…

Q: A closed traverse has the following data: Line Azimuth (°) Distance (m) AB 47.2 BC 115 762.39 CA…

A: Closed Transverse For closed Transverse,Σ Lattitude = Σ L = 0Σ Departure = Σ D = 0Line…

Q: The following readings were observed with a level: 1.143 (BM), 1.765, 2.566, 3.820 CP; 1.390, 2.262,…

A: Given readings : 1.143 (B.M) 1.765 2.566 3.820 1.390(C.P) 2.262 0.664 0.433 3.722(C.P) 2.866 1.618…

Q: Problem 8 Data for the three-level section of a road are as follows: Station Left Centre Right +…

A: Surveying mainly considers the branch of measurement and levelling of the points on the ground…

Q: A computational method used to calculate the enclosed area in a loop traverse when the coordinates…

A: A computational method used to calculate the enclosed area in a loop traverse when the coordinates…

Q: The distance between two points A and B measured along a slope was 270 m. Determine the horizontal…

A: Determination of horizontal distance in different 3 conditions

Q: Q2 In leveling works along a longitudinal section, the natural land levels that were taken at 30 m…

A: Uniform slope at all points Points Elevation (m) Distance (m) Level of road (m) Cutting (m)…

Q: SITUATION F: The following interior angles of a triangle traverse were measured with the same…

A: Given data : ∠A=41∘∠B=77∘∠C=63∘

Q: Table 1 shows a closed traverse data by student from UiTM Perlis, find out the interior and exterior…

A: Fore Bearing +- 180° = Back Bearing For Clockwise ? Traverse Previous BackBearing - present Fore…

Q: 1. The interior angles X, Y, and Z of a triangular traverse were measured with the same precision.…

A: Given, Interior angle at station, X = 41o and number of measurements = 3Interior angle at station, Y…

Q: Problem 8 Data for the three-level section of a road are as follows: Station Left Centre Right +…

A: Surveying is a very important branch of civil engineering as it is mainly dealt with the measurement…

Q: a highway project: a) 113.26 m, 35.48 m, and 18.60m b) 50.08 m, 39.25 m, and 7:14 m c) 243.55 m,…

A: (a) Given data: Length of pit = 113.26 m Width of pit = 35.48 m Height of pit = 18.60 m Since this…

Q: The location survey of the proposed road passes through a rough terrain and crosses a small valley…

A: Fig a)

Q: A closed traverse has the following data: Line Departure (m) Latitude (m) AB 64.86 16.04 BC 84.51…

A: The latitude of a line is its projection on north-south meridian and is equal to the length of the…

Q: An open channel is to be designed to carry 1 m3/s at a slope of 0.0065. The channel material has n =…

Q: 1. A traverse line was measured in three sections: 295.85 m at slope 8045’, 149.58 m at slope…

Q: In a closed-polygon traverse, compute the closure error of you know the coordinates of the first and…

Q: The difference of elevation between B and C was taken by a survey party using different trials and…

Q: The interior angles X, Y, and Z of a triangular traverse were measured with the same precision. The…

A: Given: Station Interior Angle Number of measurement X 41° 3 Y 65° 4 Z 75° 2

Q: Given in the accompanying tabulation are the observed data for traverse obtained from a transit tape…

Q: A transit with a stadia interval factor of 100 was set up at C with elevation of 500m. and the…

A: Given- Stadia interval factor=100Elevation=500mStadia constant=0.30HI=1m

Q: slope measurement of 545.38 m is made between points and B. The elevation of A is 424.25 m and that…

Q: Subject = Transportation Engineering Choices for mean and median is 2998.67, 2895.67, 3125.25,…

Q: The location survey of the proposed road passes through a rough terrain and crosses a small valley…

A: Fig a) Fig b)

Q: Interior Angle Traverse The observed interior angles of a closed traverse are as follows: A, 153°…

A: Determine the angular closure and adjust the measured angles by assuming the angular error is of the…

Concept explainers

Photogrammetry

Photogrammetry is a technology of taking measurements of physical objects present in the environment, using photographs. It includes the process of recording and analyzing a three-dimension image in the two-dimension form. Photogrammetry was invented around 150 years ago in 1851 by Aimé Laussedat, he was also known as the father of photogrammetry, but this method was not in use until 50 years after its invention. This method was first used in Germany by Dr. Albrecht Meydenbauer in 1893 who was the director of the Royal Prussian Photogrammetric institute founded by him.

Question

100%

For data below the average P over an area by Isohyetal method is? if the area between each two stations = 100 Km ^2 (P1= 150mm, P2= 127, P3=152mm, P4= 152 mm)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the figure , the width of a river being observed is 80m, Assuming the transit beingused has a K value of 99 and C value of 0.20.,Determine the distance DL and DR, andstadia intercept of DL.(Assume stadia intercept of DR is 1.25)
Problem 2. The table below shows stadia readings taken by a transit set at point A between two points X and Y with stadia interval factor of 100.80 and stadia constant of 0.381. a) Find the horizontal length of line XY. b) Determine the elevation of Point A if the elevation Y is 100 m and HI=1 m c) Determine the difference in elevation between points X and Y.
For data below the average P over an area by thiessen method is? if the area for each station = 222 Km ^2 (P1=150mm, P2= 127mm, P3= 152mm, P4=106mm)
For the following data, compute the horizontal distance for a recorded slope distance AB.(a) AB = 104.93 ft, slope angle = 2°13′46″(b) AB = 86.793 m, difference in elevation A to B = -2.499 m
Problem no. 1: The difference in elevation between observed points A and B is 47 m and the horizontal distance between them is 73. The difference in elevation between observed points C and D is 27 m and the horizontal distance between them is 38. With transit at Sta. O, additional information was obtained as shown in the table. Assume K=100 and f=0.25 and c=0.25. Determine the stadia interval at A Determine the stadia interval at B Determine the stadia interval at C Determine the stadia interval at D
A pipeline transporting natural gas is to be laid out on the side of a hill (from pt. A to pt. B) as shown in the figure. Trigonometric leveling was performed where a transit (with a stadia factor of 100.8 and stadia constant of 0.38) was set at pt. C somewhere between pts. A and B. The following readings were observed. How long is the inclined section of the pipe? Determine the material cost of the inclined pipe to be installed if the material costs P 5,000/meter.
Consider the area shown in graph. Suppose that a=4 m, b=6 m, and k=3/8 m^-1. Locate the centroid y of the shaded area.
The observe interior angles of the triangle are A= 35°14'37'', B= 96°30'09'', and C= 48°15'05''. Determine the discrepancy for the given observation and the most probable value of each angle.
From the results of a hydrographic survey of a lake the following data were obtained. Aa = 1240.71 sq.m. (area enclosed by the boundary of the water surface) Ab = 752.79 sq.m. (area enclosed by contour B) Ac = 397.77 sq.m. (area enclosed by contour C) Ad = 178.44 sq.m. (area enclosed by contour D) Ae = 48.33 sq.m. (area enclosed by contour E) If the vertical distance (h) between contour levels is 1.50 m, determine the total volume of water in the lake above the level of contour E. Resolve the above problem if the vertical distance between contour levels is 2.0m. Which has a larger value of volume?
From the results of a hydrographic survey of a lake the following data were obtained. Aa = 1240.71 sq.m. (area enclosed by the boundary of the water surface) Ab = 752.79 sq.m. (area enclosed by contour B) Ac = 397.77 sq.m. (area enclosed by contour C) Ad = 178.44 sq.m. (area enclosed by contour D) Ae = 48.33 sq.m. (area enclosed by contour E) If the vertical distance (h) between contour levels is 1.50 m, determine the total volume of water in the lake above the level of contour E.
From the results of a hydrographic survey of a lake the following data were obtained. Aa = 1240.71 sq. m (Area enclosed by the boundary of the water surface) Ab = 752.79 sq. m (area enclosed by contour B) Ac = 397.77 sq.m (area enclosed by contour c) Ad = 178.44 sq. m (area enclosed by contour D) Ae = 48.33 sq. m (area enclosed by contour E) if the vertical distance (h) between contour levels is 1.50m, determine the total volume of water in the lake above the level of contour E.
A transit with a stadia interval factor of 100.8 was set at C on the line between points A and B, and the following stadia readings were observed. If the stadia constant is 0.381 m., determine the following: Length of line AB. Difference in elevation between points A and B. Find the horizontal distance from the transit to the rod held at B. Show the solutions and sketches.