For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa. 0.9 m ACD=500 mm² 0.6 m 25 kN AAB 850 mm² 1.5 m B 0.3 m² 0.2mA=

For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the deformation incurred by rod CD. Also, calculate the angle of tilt in radians for bar AC and the horizontal displacement of point F. Use E = 120 GPa. 0.9 m ACD=500 mm² 0.6 m 25 kN AAB 850 mm² 1.5 m B 0.3 m² 0.2mA=

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
2. (CASTIGLIANO'S THEOREM) Determine the vertical displacement of point B of the beam shown below. E= 200 GPaI= 150(10) mmsP= 15.4 kNQ= 6.4 kN/ma = 6 m
For the truss in the given figure, compute the horizontal and vertical components of the displacement of joint B produced by the 100-kip load. The area of all bars is 4.8 in.2 and E = 24,000 kips/in.2.
Shear force acting on section H in the figure Shear stress y when T = 50 kN acts Draw the distribution of zy.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70048581 Pa and angle of twist of 2.29ᴼ. Use G = 83000000000 Pafor the shaft, x = 2.01 m, and y = 1.69 m. Round off the final answer to two decimal places.
(a) Compute the horizontal displacement of joint B produced by the 240-kN load in Figure P8.10. For all bars, area = 2400 mm2 and E = 200 GPa. (b) Assuming that no load acts, determine the horizontal displacement of joint B if support A moves 20 mm to the right and 30 mm down and support E moves downward 36 mm.
Determine the displacement at C of the beam in this Figure using Conjugate Beam. E- 29,000 ksi and I=600 in.
Consider the following frame. The frame is supported by guided support at x=0 and roller support at x=20. Q: Using method of virtual work, solve the horizontal displacement at point C. q0: 4 kN/m
In the figure, compute the vertical and horizontal components of displacement of joint E produced by the loads. The area of bars AB, BD, and CD = 5 in^2 , the area of all other bars = 3 in^2. E = 30,000 kips/in^2 . USE CASTIGLIANO'S THEOREM.
Using forced method of analysis, determine the reaction of supports from the beam shown in the figure. EI is constant. Possible Answers: Ay=698/27 kN (Upward) By=1484/27 kN (Upward) Cy=518/27 kN (Upward)
In Figure P8.27 support D is constructed 1.5 in. tothe right of its specified location. Using Bernoulli’s prin-ciple in Section 8.8, compute (a) the horizontal and verti-cal components of the displacement of joint B and (b) thechange in slope of member BC.