Flexural and Horizontal Shear StressAnswer number 2 only Provide a neat, complete and orderly solution and diagram to the following problems.1. A meter long circular rod is used as a cantilever beam and is loaded with a 10 N force at its free-end. Determine the safe diameter of the rod if the allowable flexural and shearing stresses are1.6 MPa and 14 kPa, respectively.2. For the beam and loading shown, determine the maximum flexural stress (compression andtension) and the maximum horizontal shear stress. Show that the centroid is located at 77.5 mmfrom the bottom of the beam and Ina = 2.35 x 106 mmª.10 kN100 mm3 kN/mD10 mm1.5 m1.5 m2.2 m10 mm77.5 mm100 mm

As asked The solution of question 2 is presented in next steps

For the beam and loading shown, determine the maximum flexural stress (compression and tension) and the maximum horizontal shear stress. Show that the centroid is located at 77.5 mm from the bottom of the beam and INA = 2.35 x 106 mmª. 2. 10 kN 100 mm 3 kN/m D ---TE 10 mm B 1.5 m 1.5 m 2.2 m 10 mm 17.5 mm 100 mm

For the beam and loading shown, determine the maximum flexural stress (compression and tension) and the maximum horizontal shear stress. Show that the centroid is located at 77.5 mm from the bottom of the beam and INA = 2.35 x 106 mmª. 2. 10 kN 100 mm 3 kN/m D ---TE 10 mm B 1.5 m 1.5 m 2.2 m 10 mm 17.5 mm 100 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam has a circular cross section of 263 mm diameter. If the working bending stress is 199 MPa, determine the largest allowable intensity wo of the uniformly distributed load that can be applied to the beam. Round your answer to 2 decimal places.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
A rectangular beam has a dimension of 210 mm x 260 mm. The simply supported beam is 5-m long and carries a concentrated load of 25 KN at the midspan. What is the maximum flexural stress of the beam? Blank 1 (use two decimal places)
A rectangular “Apitong” beam 50mm x 300mm is used as a simply supported beam 3.2m long. Determine the largest uniformly distributed load, which can be, applied over the central half of the beam if the flexural stress is limited to go 12MPa?
Consider the beam shown in (Figure 1). Suppose that M = 9 kip⋅ft, P = 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part A Part complete Determine the internal normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to…
A hollow rectangular column carries three axial loads as shown in Fig. 4. If P1=100kN, P2=200kN, and P3=300kN respectively, determine:(a) the magnitude and position of the resultant load with reference to X-X and Y-Y axes;(b) the combined stresses at each of the corners a, b, c and d.
Situation 2. A 4m cantilever beam has a live load of 50 kN at its free end. A. . Draw the shear and bending moment diagrams of the beam considering its live loadonly. B. If the allowable stress is 150 MPa, what is the most economic W-flange that might be used? C. What is the actual maximum stress in the beam?
A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 10 KN/m all through out its length and a concentrated load of 500 N at the midspan. The cross-sectional area of the beam is indicated below. What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) What is the actual shearing stress of the beam in MPa? (use two decimal places, no need for unit)
Completely solve and box the final answer. Illustrate the problem. Write legibly 2. A cantilever beam 3 m long supports a uniform load of 4.5 kN/m and a concentrated load of 3.4 kN at the end. Determine the minimum diameter of the beam with a flexural stress of 12.5 MPa and a shearing stress of 1.4 MPa. For this question, round off to the nearest multiple of 25 mm.
A beam is to be designed to carry a maximum shear force of 100 kN and bending moment of 250 kNm. The cross-section of the beam is rectangular with a dimension depth, D is equal to 2 times the width, B. If the allowable bending stress is 150 N/mm2 and the allowable shear stress is 10 N/mm2, determine the minimum cross-sectional dimension of the beam.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. the fc' is 28MPa, fy is 420MPa and Wu is 89.9kN/m. 1. what is the ultimate moment capacity of the beam? 2. what is the height of the equivalent stress block? 3. Determine the number of bars required for this beam
Find shear force value under point load 10 Kn