For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, and (b) the deflection at B. Assume that El is constant for the beam. Let w = 9 kN/m, L = 6.0 m, E = 220 GPa, and I 105 x 106 mm4 B L/2 L/2 Part 1 Draw a free body diagram of the beam and solve the reactions A, and Cy. L/2 C, Answer: kN Ay = i kN Cy = i

For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, and (b) the deflection at B. Assume that El is constant for the beam. Let w = 9 kN/m, L = 6.0 m, E = 220 GPa, and I 105 x 106 mm4 B L/2 L/2 Part 1 Draw a free body diagram of the beam and solve the reactions A, and Cy. L/2 C, Answer: kN Ay = i kN Cy = i

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the maximum deflection, and (c) the slope at A. Assume that EI is constant for the beam. Let w = 14 kN/m, L = 4.5 m, E = 180 GPa, and I = 130 x 106 mm4. Part 1 Draw a free body diagram of the beam and solve the reaction forces Ay and By. Forces are positive upwards. Answer:Ay = kNBy = kN Part 2 Cut a cross-section through the beam at any point and draw a free body diagram. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for M at x = 2.3 m.Answer:M(x = 2.3 m) = kN·m
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, and (b) the deflection at B. Assume that El is constant for the beam. Let w = 6 kN/m, L = 3.0m, E = 180 GPa, and I = 145 x 10^6 mm^4.
For the beam and loading shown, integrate the load distribution to determine (a) the equation of the elastic curve, (b) the deflection at the left end of the beam, and (c) the support reactions By and MB. Assume that EI is constant for the beam. Let w0 = 11 kN/m, L = 3.5 m, E = 195 GPa, and I = 125 x 106 mm4.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, and (b) the deflection at B. Assume that EI is constant for the beam. Let w = 14 kN/m, L = 4.5 m, E = 215 GPa, and I = 125 x 106 mm4
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
A cantilever beam AB is loaded as shown in Figure 1. EI is constant for the beam. L = 2.7 m and P = 8.9 kN. Write down your L and P values and answer parts a to c below. (a) Using the moment area method, determine the slope of the beam at B. (b) Using the conjugate beam method, determine vertical deflection at B. (c) Draw the free body diagram (FBD) of the virtual force system for the virtual work method to determine the vertical deflection at the mid-span of the beam. (Note: No calculations are required and show only the FBD).
EI is constant (Assume EI = 1 kN-m2). Solve using the conjugate-beam method. Determine the (a) maximum upward deflection and the (b) maximum downward deflection If moment diagrams are referred at A, what is the total upward load for the equivalent conjugate beam If moment diagrams are referred at B, what is the total upward load for the equivalent conjugate beam
For the beam shown, EI = Constant. Determine the following: A. Slope at B B. Deflection at C C. Location of the maximum deflection D. maximum deflection
EI is constant (Assume EI= 1 kN-m^2) use moment area method 1.) determine the location of the maximum deflection from A2. ) determine the maximum deflection
SOLVE THE FOLLOWING USING ( SLOPE DEFLECTION METHOD) 1) Reaction at D, Rd in kN 2) Moment at D, Md in kN-m
For the loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at the free end, and (c) the slope at the free end. Assume that EI is constant for the beam. Let w = 8 kN/m, L = 3.0 m, E = 205 GPa, and I = 100 x 106 mm4. Cut a cross-section through the beam at any point and draw a free body diagram. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for M at x = 1.5 m.Answer:M(x = 1.5 m) = kN·m
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI:(a) Use the Moment-area Method to obtain the Slope of Point A after deformation and the vertical displacement of Point C (Deflection)(b) Use the conjugate beam method (Conjugate Beam Method) to obtain the slope (Slope) after the deformation of point A and the vertical displacement (Deflection) of point C *The correct answer is 24 kN-m2/EI clockwise and 58.7 kN-m3 /EI down, but I need to calculate steps, thanks