For the beam cross section shown below, an applied anticlockwise torque of 30,000 Nmm is applied, but no other forces.dbBy doing an equal twist analysis, we know that q1 = 2.5 x qi1The dimensions are:a = 121 mm b=277 mm c= 117 mm d=71 mmCalculate the value of q11Enter your answer as N/mm, to 3 significant figures, but without the units. You have an error margin of 3%.Type your answer.

Bredt-Bratho theory: The basic assumption in the Bredt-Bratho theory of torsion is the cross-section…

For the beam cross section shown below, an applied anticlockwise torque of 30,000 Nmm is applied, but no other forces. d b By doing an equal twist analysis, we know that q1 = 2.5 × q11 The dimensions are: a - 121 mm b-277 mm c- 117 mm d- 71 mm Calculate the value of q11 Enter your answer as N/mm, to 3 significant figures, but without the units. You have an error margin of 3%. Type your answer.

For the beam cross section shown below, an applied anticlockwise torque of 30,000 Nmm is applied, but no other forces. d b By doing an equal twist analysis, we know that q1 = 2.5 × q11 The dimensions are: a - 121 mm b-277 mm c- 117 mm d- 71 mm Calculate the value of q11 Enter your answer as N/mm, to 3 significant figures, but without the units. You have an error margin of 3%. Type your answer.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 29P: A structural member with a rectangular cross section as shown in the accompanying figure is used to...

See similar textbooks

Similar questions

A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum magnitude of shear force, positive value: Maximum magnitude of bending moment, positive value: b) Determine the maximum bending stress and shear stress that occurs in the beam. Maximum bending stress: Maximum shear stress
For the beam and loading shown in Figure below, determine the beam deflection at point H. Assume that EI = 8 × 104 kN·m2 is constant. Express your answer in mm and use three decimal places. Indicate the negative sign in your final answer if the deflection is downward.
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Round-off to 3 decimal places. a = 8.5 m, b = 3.3 m, c = 9.5 kN/m, d = 27 kN-m. - Slope of the elastic curve at B in degrees. Indicate negative sign as necessary. - Deflection at D in mm. Indicate negative sign if downward. - Deflection at midspan in mm. Indicate negative sign if downward.
As shown in the figure, a square-threaded screw is used in a vise toexert a pressure of 2 tons. If the screw is double-threaded and has a pitchof 0.25 in. and a mean radius of 1.5 in., determine the torque that must beapplied at B to create this pressure. Assume the coefficient of friction to be0.15.
A cantilever beam carries a varying load as shown in the figure. If E = 200,000 Mpa and I=120×10^6 mm^4 Determine the following. Use Double Integration Method 1. Slope at free end 2. Deflection at 4m from the support
determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section and E=200 GPa Enter the absolute value only and round off your answer to 3 decimal places PLS. ANSWER ASAP, I'LL RATE. THANKS
For the beam loaded as shown in the figure 3, determine the deflection at midspan of the beam in mm using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places a = 5.5 m, b = 3.3 m, c = 20.3 kN/m, d = 27 kN.
4. This figure shows a cantilever beam that is subject to a point load and a moment. What is the vertical displacement at the tip of the beam? Assume E = 200 GPa and / = 1560 X 10° mm%. A. 58.7 mm B. 68.9 mm C. 89.0 mm D. 100 mm
Given beam loaded as shown below. Assuming EI is constant. 1. Which of the following gives the location of maximum deflection. a. 2.212 m b. 1.958 m c. 1.334 m d. 1.456 m 2. Which of the following the value of maximum deflection. a. 29.4/EI b. 17.5/EI c. 20.7/EI d. 14.2/EI
Develop the generalized piecewise equation for the elastic curve for the beam as a function of x referenced from A. Your equation should be in terms of P, x, and L. Take EI as a constant. NOTE: A is a pin support and B is a roller. Plot the deflected shape in excel for P = 10 kips, L = 15 ft, E = 29,000 ksi, and I = 150 in^4. Plot using 0.5 ft. increments for x.