For the beam of constant section shown in the figure, determine the deflection at c and the slope at b. It is requested to solve using the conjugate beam method and castigliano. 35KN 3m B 1.5m 22KN.m

Q: Material Strengths: of=41.4 MPa, fy = 414 MPa Determine the moment capacity (M) of the beam with the…

A:

Q: Water flows from a large open tank, through a valve and out a pipe to atmosphere. A = 9 cm², Az =…

A: Given data:- The given area is, A=9 cm2 The difference in the height between the pipe and the top of…

Q: Steam enters a turbine at 30 bar, 300°C (u = 2750 kJ/kg, h = 2993 kJ/kg) and exits the condenser as…

A: Steam enter  H enter= 2993kj/kg Steam exits Hexit = 226kj/kg Heat loss in surrounding = 50kj/kg Work…

Q: If the restraint at the midspan of the beam is removed, how much deflection should it resist such…

A: Given data in question  Continous beam Span member length  UDL To find out  How much does middle…

Q: Q-3 A vertical load W is applied to the rigid frame ABC shown in Fig.3. Use Castigliano's theorem to…

A:

Q: A tension member is an L 150x90x8 connected to an 8-mm-thick gusset plate with 6-020 mm diameter,…

A: Answer We are given L 150 x 90 x 8 gusset plate thickness = 8 mm Fy = 248 Mpa Fu = 400 Mpa Bolt…

Q: 4m 4m Problem #8: 3m 5KN 3m B 1.5m 8KN 1.5m C 2m 2m

A: Find support reaction.    Joint B is pin joint so moment from either side of  is zero.

Q: A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length.…

A:

Q: 1. Given are the stations and elevations of a proposed symmetrical parabolic highway curve.…

A: The resulted curve will clear the boulder at 6+276  Curve elevation at 6+276 will be 92.72 m

Q: If the magnitude of the resultant force is to be 530N, directed along the positive y axis, determine…

A: Given :

Q: Answer carefully the following questions : 1-What is the effect on physical properties of cement, if…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A reinforced concrete beam section is "b" wide and "h" deep. It is to be reinforced with the given…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: A Y-shaped tube is inserted upside down so that the left foot and right foot are immersed in two…

A: Given- density of first liquid ρ1=0.80 g/cm3density of second liquid ρ2=0.75 g/cm3height of the…

Q: Colum A and Column B are spaced at 2.5m apart and are carrying the nominal loads tabled below. Left…

A: We’ll answer the first question 1.1 since the exact one wasn’t specified. Please submit a new…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Why is motivating relevant to the job of the engineer manager?

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: The 79-lb force P is applied to the 200-lb crate, which is stationary before the force is applied.…

A:

Q: If the whole circle bearing of side AB of an equilateral triangle ABC is 38°45', then the bearing of…

A: given- whole circle bearingWCB=38o45'Bearing of third side CA needs to be find out.

Q: Determine the maximum absolute bending strain in the following tubular shaft if di = 160 mm and do =…

A: Determine the maximum absolute bending strain???

Q: Two batches of concrete cylinders were made with and without a calcium chloride (CaCl2) accelerator…

A: Given values: Cylinder no: 1 2 3 4 5 6 curing time (days) 1 3 7 14 21 28 Compressive strength…

Q: A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected to an…

A: Solution:  Given: Mu = 750 kNm b = 350 mm de = 500 mm d' = 70 mm fc = 28 MPa fy = 415 MPa

Q: Torsional moment of resistance, T of the

A: Given,  Closed thin walled tube has thickness=t  Mean closed area within the boundary of the…

Q: Two simply supported beams are made up of the same material and are of the same cross-section. Both…

A: given- 2 simply supported beams-same material and same cross-sectionSame UDLspan of beam=2 m and 4…

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Determine the forces in members BE and CE of the loaded truss.

Q: Determine all the supports reactions of the given figure

A: ###Determination of Support reaction ###

Q: = Steam enters a turbine at 30 bar, 300°C (u = 2750 kJ/kg, h 2993 kJ/kg) and exits the condenser as…

A: Find work output of turbine.

Q: By the method of sections, determine the shear and moment diagrams developed in the beam, and the…

A: Answer Let us first draw the free body diagram of forces on beam. To draw free body diagram separate…

Q: The 99-lb force P is applied to the 240-lb crate, which is stationary before the force is applied.…

A:

Q: 8 KN/m 30 KN/m 2.5m + 1.25 60 KN 2.5m 30 KN 60° -0.751--150- + pin 5 KN/m 30 KN/m 3.0000 20 KN.m

A:

Q: Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions:…

A: Given values: Consider the graph given.   Maximum size of aggregate is the smallest size of sieve…

Q: A 18-ft thick clay layer in the field (drained on one side) is normally consoli- dated. When the…

A:

Q: The figure shows the cross section of a rectangular column 400mm by 600mm reinforced with 8-25m…

A: Column: Compression member is a structural member which is primarily subjected to axial compression.…

Q: 11.4 The following are the results of a consolidation test on a sample of a clayey soil. Pressure, o…

A: Given :

Q: The surface tension of a liquid is being measured with a ring. The ring has an outer diameter of 10…

A:

Q: Bolted and Riveted Connections 1. From the bolted connection shown, the diameter of bolts is 18mm0…

A: Solution: Given: db = 18 mm dbo = 18+3 = 21 mm Section: 100 x 75 x 8 mm Ag = 1340 mm2 t = 9 mm A36…

Q: 4-How the consistency of cement paste is measured? 5-State the significance of initial setting time…

A: ANS 4: A cement paste with a standard consistency is one that will allow a vicat plunger with a 10…

Q: Q- Calculate the capacity (veh/hr) of the road when the reaction time of the driver is 2s. The…

A:

Q: The population in Camilia Apartment is 3500 and solid waste is collected on Sunday and Wednesday in…

A: given- Population in Camilia Apartment=3500Density of waste =310 kg/m3

Q: In order to evaluate the suitability of nonpotable water available at the job site for mixing…

A: Given values: Compressive strength of mortar cubes after 7 days of curing tested and failure loads…

Q: 2000 lb A 20' Determine the internal force on: B 1000 lb 560 lb D G F 20' C 20' E 20' G 20' Member…

A:

Q: Three pipes steadily deliver water at 20°C to a large exit pipe as shown in the figure given below.…

A: Given Data: Diameter of pipe1 = D1 = 4 cm = 0.04 m Diameter of pipe2 = D2 = 5 cm = 0.05m Diameter of…

Q: Two identical plates of 63 mm wide and 3 mm thick is connected by a square pin with side dimension…

A:

Q: A force P is being applied laterally to the crate which has a center of gravity at G. The…

A: Find P value to impend tipping of the crate

Q: If 2% solution of a sewage sample is incubated for 5 days at 20 degrees and depletion of oxygen was…

A: Given data, Percentage of sewage sapmle solution= 2% Dissolved oxygen, At 20°c = 5PPM Bod5=?

Q: A drained triaxial test was conducted on a normally consolidated clay speci- men with a chamber…

A:

Q: The rotating stepped shaft in the figure is produced from 85080M30 steel by machining method. It…

A: Stepped Shaft : Stepped shaft is made to deal with the different levels of stresses which are varies…

Q: 10.7 Point loads of magnitude 125, 250, and 500 kN act at B, C, and D, respectively (Figure 10.40).…

A: To find out the increase of vertical stress at a depth of 10 m below the point of A.

Q: A cantilever beam, 3 m long, carries a uniformly distributed load over the entire length. If the…

A: Given data- Cantilever beam span L=3 mUDL over entire spanslope θ at free end=1oTo Find-The…

Q: 4.0mi 4.0mi 4.0ml L 5.0m all columns 300mmx300mm 1000mm 300mm Section A-A -5.0m- || A ||___ 150mm…

A: Solution: Given: largest length = 5 m smallest length = 4 m slab thickness = 150 mm bw = 300 mm d =…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.