For the cantilever bearn shown, determine the normal and shear stresses acting at point K. The cross-sectional dimensions of the beam cross section and the location of point K are also shown. Use the following values: a = 2.15 m, b =0.80 m, Py 10 kN, P₂ = 8 kN, b = 165 mm, k = 59 mm, t = 12 mm, h = 42 mm, t = 6 mm, and d = 260 mm.by"

Answered: Image /qna-images/answer/c4025c92-a14e-4f9f-aaa3-51afe8e5dbe0.jpg

For the cantilever beam shown, determine the normal and shear stresses acting at point K. The cross-sectional dimensions of the bear cross section and the location of point K are also shown. Use the following values: a = 2.15 m, b = 0.80 m, Py 10 kN, P₂8 kN, by 165 mm, k = 59 mm, 12 mm, h 42 mm, 6 mm, and d = 260 mm. 4

For the cantilever beam shown, determine the normal and shear stresses acting at point K. The cross-sectional dimensions of the bear cross section and the location of point K are also shown. Use the following values: a = 2.15 m, b = 0.80 m, Py 10 kN, P₂8 kN, by 165 mm, k = 59 mm, 12 mm, h 42 mm, 6 mm, and d = 260 mm. 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer correctly, badly need it. Thank u godbless The internal shear force at a certain section of a steel beam is V= 8.8 kN. The beam cross-section shown in the figure has dimensions of b=141 mm, c=31 mm, d=63 mm, and t=6 mm. Determine: (a) the shear stress at point H. (b) the shear stress at point K. (c) the maximum horizontal shear stress in the cross-section. Break the cross-section into five rectangles, as shown. It is seen that the two labeled with a (1) are identical, and the two labeled with a (2) are identical. Find A1, the area of rectangles (1), and y1, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (1). Similarly, find A2, the area of rectangles (2), and y2, the vertical distance from the bottom edge of the cross-section to the centroid of rectangles (2). Then, find A3 and y3 for rectangle (3). A1= mm2 y1= mm A2= mm2 y2= mm A3= mm2 y3= mm Find y¯, the vertical…
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa
As seen in the figure, ABC rod with end-A fixed support pipe section has an outer diameter of 30 mm and an inner diameter of 24 mm. 50 N force at an angle of 30 ° with the y-axis at the free end C to the ABC rod is implemented. (a)Show and calculate the cross-sectional effects on the cross-section a a. (b) Calculate the stresses occurring at the H point of the ABC bar and calculate these stresses
Calculate the design moment strength Mu for the following section. Take f'c = 40 MPa. Sketch the strain and stress distribution diagrams for each section and try to work out your solutions using equilibrium conditions. Yield stress for N bars is 500 MPa. 75 700 60 1500 T 4N28 450
Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. Take P = 9.25 kN. A 30 mm B 400 mm 45 mm '30 mm' 500 mm The maximum tensile stress is 10 mm MPa, and the maximum compressive stress is MPa.
The steel beam has the cross section shown. The beam length is L = 7.7 m, and the cross-sectional dimensions are d = 360 mm, b = 205 mm, 12 mm, and tw = 6 mm. Calculate the largest intensity of distributed load wo that can be supported by this bearn if the allowable bending stress is 245 MPa. Answer: Wo= Wo B kN/m be I y T
d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
For the cantilever beam shown. find the value of Normal stress due to axial :load at point A 4 KN 6 KN.m D. 2 KN IB 10 m Diameter=100 mm E B
H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of the shape are shown in Figure 2 b. determine: (a) the maximum tension bending stress at any location along the beam, and (b) the maximum compression bending stress at any location along the beam. The Consider the entire 24-ft length of the beam and 16.00 in. y 7 kips 16 kips 17 kips 1.50 in. 6 kips/ft 18.50 in. В C E 6 ft 4 ft 10 ft 4 ft 0.75 in. FIGURE 2 a. FIGURE 2 b.
H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of the shape are shown in Figure 2b. determine: The Consider the entire 24-ft length of the beam and (a) the maximum tension bending stress at any location along the beam, and (b) the maximum compression bending stress at any location along the beam. 16.00 in. y | 7 kips | 16 kips 17 kips 1.50 in. 6 kips/ft 18.50 in. B |C D E 6 ft 4 ft 10 ft 4 ft 0.75 in. FIGURE 2 a. FIGURE 2 b.
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.