Question 1 For the cross-section shown in Figure Q1, and based on an origin that is located at the bottom most and left most location on the cross-section, determine through calculations: (i) The location of the centroid, and (ii) The second and product moment of areas, starting with the general expressions. 60 10↓↓ 10 120 100 All units in mm 10

Question 1 For the cross-section shown in Figure Q1, and based on an origin that is located at the bottom most and left most location on the cross-section, determine through calculations: (i) The location of the centroid, and (ii) The second and product moment of areas, starting with the general expressions. 60 10↓↓ 10 120 100 All units in mm 10

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.17P: A W867 section is joined to a C1020 section to form a structural member that has the cross section...

See similar textbooks

Similar questions

8.7 Determine the position of the centroid of the section shown in Figure 8.1 1, namely y . Determine also Ixx for this section.
A block of stone is cut so that its cross‑section is a parallelogram. The width of the bottom side is ?=0.655 m, the height of the top of the block is ℎ=0.915 m, and the top right corner overhangs a distance ?oh=0.195 m from the bottom corner as shown. Assume that the block is of uniform density, so that the center of gravity of the block is located at the geometric center.
A post-tensioned prestressed concrete beam is shown in figure 1. Determine the coordinates of the centroid of the beam.
3.1)Determine the location of the centroid for the cross section shown in Figure 3 and draw a scaled sketch of the cross-section, clearly showing the centroid and indicate it's distance from the selected origin. (Start your calculations be setting an origin at the bottom, left most point on the cross section). 3,2)Calculate the second moment of areas about the centroidal axes for the beam cross-section from Figure 3.
Calculate the centroid of the composite shape AB= 85 C=1 BC = 12 only HANDWRITTEN answer needed ( NOT TYPED)
Figure (a) shows the cross-sectional dimensions for the structural steel section known as C1020 (channel with a nominal depth of 10 in., weighing 201b/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following properties for the cross section: A=5.88in.2,Ix=78.9in.4, and Iy=2.81in.4. If two of these channels are welded together as shown in Fig. (b), find Ix and Iy for the resulting cross section.
Using integration, locate the centroid of the area under the n-th order parabola in terms of b, h, and n (n is a positive integer). (b) Check the result of part (a) with Table 8.1 for the case n = 2.
Figure (a) shows the cross section of a column that uses a structural shape known as W867 (wide-flange beam, nominally 8 in. deep, weighing 67 lb/ft). The American Institute of Steel Construction Structural Steel Handbook lists the following cross-sectional properties: A=19.7in.2,Ix=272in.4, and Iy=88.6in.4. Determine the dimensions of the rectangle in Fig. (b) that has the same Ix and Iy as a W867 section.
Locate the centroid y¯ of the area. Take b = 9 in , h = 10 in .(Figure 1) Express your answer to three significant figures and include the appropriate units.
According to what is given in the cross-sectional picture at Km 1; a) Determine the condition of the cross section in KM 2 and indicate the level difference between the inner and outer edges. b) Determine the condition of the cross section in KM 3 and indicate the elevation difference between the inner and outer edges.
Using the figure shown below, determine the following: a. Centroid of the given figure with respect to reference axes b. Centroid of the line with respect to reference axes c. Location of the center of gravity d. Moment of inertia with respect to the reference X and Y axis. e. Moment of inertia with respect to centroidal X and Y axis. f. Section modulus with respect to X-axis g. Polar moment of inertia h. Polar radius of gyration
31 - A homogeneous, planar plate of constant thickness in the figure the coordinates of the centroid M(Xm,Ym) of the surface area, Find the team (x,y). t= 3 cm and a= 9 cm. Find the coordinates (Xm;Ym) on the x and y axes of the rectangle extracted from this planar plate.A) (9 ; 13)B) (9 ; 15)C) (9 ; 18)D) (9 ; 25.5)E) (9 ; 22.5)