For the design of the band brake shown, find the couple M required to turn the pipe in the V-block against the action of the flexible band. A force P = 31 lb is applied to the lever, which is pivoted about O. The coefficient of friction between the band and the pipe is 0.26, and that between the pipe and the block is 0.35. the weights of the parts are negligible. TOB M * 10" 35° 35° Ola 5" Answer: M = the tolerance the tolerance is +/-5% lb-in. 16"

For the design of the band brake shown, find the couple M required to turn the pipe in the V-block against the action of the flexible band. A force P = 31 lb is applied to the lever, which is pivoted about O. The coefficient of friction between the band and the pipe is 0.26, and that between the pipe and the block is 0.35. the weights of the parts are negligible. TOB M * 10" 35° 35° Ola 5" Answer: M = the tolerance the tolerance is +/-5% lb-in. 16"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force F and plot the result of F (ordinate) versus θ (abscissa) for 0° ≤ θ ≤ 90°.
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of compression block of the section in PART B in mm.0
Two smooth ball bearings, each of weight w and radius r, are placed inside a cylinder open at both ends. The assembly rests on a horizontal surface as shown in Figure P-3-4.12. If the cylinder is of weight W and radius R <2, find (a) the force exerted by either ball bearing on the cylinder, (b) the smallest value of W that will prevent the cylinder from tipping over. (c) Could the cylinder possibly tip if it were closed at the bottom?
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of compression block of the section in PART A in mm.0
The two blocks shown start from rest. The horizontal plane and the pulley are frictionless, and the pulley is assumed to be of negligible mass. Determine the acceleration of each block and the tension in each cord. A= 100 kg B = 260 kg
A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
2. Compute for the moment of inertia about xo and yo of the following figure. Show your complete solution.
1. A rectangular gate AB hinged at A has a width 2.0 m perpendicular to the paper, has a negligible weight. The water surface remains at the top of the gate. Determine the vertical component of the hinge force in kN to maintain equilibrium. Write your answer to the nearest three decimal places. Use unit weight of water 9.80 kN/m^3.
The assembly is made from a steel hemisphere, ρst = 7.80 Mg/m3, and an aluminum cylinder, ρal = 2.70 Mg/m3. Determine the mass center of theassembly if the height of the cylinder is h = 200 mm.
A cylindrical steel tank is manufactured based on the following data:internal pressure: 2460 psifactor of safety with respect to YP: 2.0yield stress in tension (circumferential): 56 000 psiyield stress in shear (longitudinal): 22 000 psi(a) Determine the minimum wall thickness if the diameter of the cylindrical steel tank is 7 inches.(b) Determine the maximum acceptable internal pressure if the wall thickness is 0.50 inches.Use 2 decimal places in every solved values. (25 pts)
A square plastic bar (length Lp, side dimension sp = 193 mm) is inserted inside a hollow, square, cast iron tube (length Lc = 400 mm, side sc = 200 mm, and thickness tc = 3mm). (a) What is the required initial length Lp of the plastic bar so that, when it is compressed by some force P, the final length of bar and tube are equal to legnth Lc, and, at the same time, the gap between plastic bar and cast iron tube is closed? (b) Compare initial and final volumes for the plastic bar. Assume that Ec = 170 GPa, Ep = 2.1 GPa, vc = 0.3, and vp = 0.4.