For the directional coupler with C = 15 dB and D = ∞ dB shown in Figure (2), the sourcepower is 10 W, and the bolometer reading is 30 mW. Find the power dissipated in theload (Zl) and in the matched load if: (a) the bolometer is matched to port 3, and (b)the bolometer is mismatched with return loss of 20 dB 4. For the directional coupler with C = 15 dB and D = o dB shown in Figure (2), the sourcepower is 10 W, and the bolometer reading is 30 mW. Find the power dissipated in theload (Z1) and in the matched load if: (a) the bolometer is matched to port 3, and (b)the bolometer is mismatched with return loss of 20 dB.GeneratorB34Coupling = 15 dBMatched loạdFigure 2:ww

Answered: Image /qna-images/answer/58b72854-e308-4ab6-97c2-e1729006b30d.jpg

For the directional coupler with C = 15 dB and D = ∞ dB shown in Figure (2), the source power is 10 W, and the bolometer reading is 30 mW. Find the power dissipated in the load (Zl) and in the matched load if: (a) the bolometer is matched to port 3, and (b) the bolometer is mismatched with return loss of 20 dB

For the directional coupler with C = 15 dB and D = ∞ dB shown in Figure (2), the source power is 10 W, and the bolometer reading is 30 mW. Find the power dissipated in the load (Zl) and in the matched load if: (a) the bolometer is matched to port 3, and (b) the bolometer is mismatched with return loss of 20 dB

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.46P

See similar textbooks

Similar questions

1. Based on the exercise, what do you understood about STAR connection? 2. What are the relationships between the Line parameters and Phase parameters in Star Connection?
What is a Nominal diameter , Power rating, X Max,f/pl(mm),coil (mm),Nominal impedance (O),Sensitivity (dB), Voice coil diameter, Surround Material Cloth - Sealed, Magnet type Ceramic, Magnet assembly flux (T) , Magnet weight (oz), Chassis type Pressed Steel, Cone material Kevlar loaded paper?
Hi, Would it be possible to use mesh analysis in this case?
Solve for the value of voltage Vo. Use Maxwell’s Loop Analysis method.
Use DFT method to compute the circular convolution of x(n)={4,4} and h(n)={2, 6}.
Using Routh-Hurwitz analysis, answer the following questions about the block diagram below (assume K > 0): (a) Determine the value of K that will make this system unstable (If there is one). (b) If this system does go unstable for this value of K, how many unstable poles are there? (c) Is there a value of K greater than the value found in part (a) in which the system becomes stable again?
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:The per-phase constants of a 345-kV, three-phase, 150-km-long transmission line are resistance = 0.112/km, inductance-1.1 mH/km, and capacitance = 0.02 uF/km. The line supplies a 180-MW load at 0.9 power factor lagging. Using the nominal-m circuit, determine the sending-end voltage in kV. 351.2 349.3 348.7 350.8
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
dbis 35 For the network of the Figure shown below:(a)Determine re. (b) Find Zi and Av. (c) Calculate Ai
A single phase, 50Hz transmission line connected between two buses having line resistance of 3Ω, inductive reactance of 0.2 Henry. Both the ends of transmission lines are connected with series capacitors of 400microfarads each for series compensation. Then series impedance of the line is a.(3-j31) Ω b.(3-j59.6) Ω c.(3+j31)Ω d.(3+j59.6) Ω 2- Fast decoupled algorithm is not as accurate as the exact Newton Raphson algorithm for Variable number of iteration Fixed number of iteration Variable time per iteration Fixed time per iteration
If the normalized admittance visible at a distance d from the load impedance is 1 - j5, how many mho should the input admittance of the parallel side line that must be connected to the 50 ohm transmission line at position d be? (mho = 1/ohm)
help me calculate the Rn, In or Isc, and current at Zc using NORTON’S THEOREM