For the following power system network shown in the figure, the specifications of the component are as follows: G1: 25 KV, 100 MVA, X=9% G2: 25 KV, 100 MVA, X=9% T1: 25 / 220 kV, 90 MVA, X=12% T2: 220 KV/25 kV, 90 MVA, X=12% Transmission Line 1: 220 KV, X=150 ohms T2 T1 Line 1 Bus 1 Bus 2 G2 Choose 25 KV as the base voltage at the generator G1 and 200 MVA as the MVA base. eelee ceelee

For the following power system network shown in the figure, the specifications of the component are as follows: G1: 25 KV, 100 MVA, X=9% G2: 25 KV, 100 MVA, X=9% T1: 25 / 220 kV, 90 MVA, X=12% T2: 220 KV/25 kV, 90 MVA, X=12% Transmission Line 1: 220 KV, X=150 ohms T2 T1 Line 1 Bus 1 Bus 2 G2 Choose 25 KV as the base voltage at the generator G1 and 200 MVA as the MVA base. eelee ceelee

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Similar questions

A 2000 KVA, 6600/400V , STAR/Delta was performed with short circuit and Open circuit test with the following results: O.C. Test : 400V, 150A and 15kw S.C. Test: 400V, 175A and 17kw Determine the percent impedance drop for resistance, reactance and impedance. Also calculate for the efficiency at half load, 0.80pf lagging and full load, 0.85pf leading.
A 2000 KVA, 6600/400V , Delta/Star was performed with short circuit and Open circuit test with the following results:O.C. Test : 400V, 150A and 15kwS.C. Test: 400V, 175A and 17kwDetermine the percent impedance drop for resistance, reactance and impedance. Also calculate for the efficiency at half load, 0.85pf lagging and full load, 0.8pf leading.
In the circuit of figure shown in the next slide, three impedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0 ohms, connected between conductors a, b, c and the neutral “n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABC system. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance
Transmission and distribution lines are important components of any power system study. Aluminium cable steel reinforced (ACSR) (with steel in the centre – as shown in Figure Q1 is normally chosen instead of copper for transmission Explain: (a)The choice of aluminium instead of copper (b)The need to use and place steel at the core
A three phase,Y connected, 215 V (line to line), 7.5 kW, 60 Hz, three pole IM has the following parameter values in Ohm/phase referred to the statorR₁ = 0.294 Ohm, R₂ = 0.144 Ohm, X₁ = 0.203 Ohm, X₂ = 0.409 Ohm, Xm = 10.25 Ohm.The total friction,windage and core losses may be assumed to be constant at 350 W independent of load. For a slip s = 0.02, compute the followingsa) Stator Currentb) Power Factor(pf)c) Rotor Speedd) Power Output(Shaft)e) Output(Shaft) Torquef) Efficiency(n)
For a 220V, 60Hz single phase voltage controller is used for controlling flow of power in to a circuit consisting load of Xl =12 ohms and R=5 ohms. Which of the following represents the correct value of the maximum power and power transfer? (a) Pmax=9.68 kW, p.f =0.6 (b) Pmax=3.72 kW, p.f =0.6 (a) Pmax=9.38 kW, p.f =0.38 (a) Pmax=1.43 kW, p.f =0.38
In the circuit of figure shown in the next slide, threeimpedances are 12 – j10 ohms, 10 + j20 ohms, and 15 + j0ohms, connected between conductors a, b, c and the neutral“n” of a balanced 230 volts, 60 hertz, 3 phase, 4 wire, ABCsystem. Using Van as the reference vector, determine:a. Current in each impedanceb. Neutral current Inc. Readings of wattmeters W1, W2, & W3d. Power in each impedance ..
Complete the table using Kirchhoff's Laws Compose the voltage equations based on the variables given.Retain the signs generated by the tracing directions. Multiply with the least common factor to remove any fractions. KVL @ loop A: k11Vx + Z12Ix + Z13Iy = Source1 KVL @ loop B: k21Vx + Z22Ix + Z23Iy = Source2 KVL @ loop C: k31Vx + Z32Ix + Z33Iy = Source3
A high-voltage transmission line with a resistance of .39ohms/km carries a current of 1030A. The lines delivering the power are at a potential of 770kV at the power station. These lines carry the current to a city located 175km from the station. What is the power loss due to resistance in the line? (1MW=1x10^6W) -.0087MW -72.4MW -.793MW -.070MW -4.8MW At the power plant, the electric potential between the power lines is 770kV. What will be the electric potential between the power lines when they reach the city? -770kV -0kV -700kV -70.3kV
Consider a house that has a 120V mains with mains frequencyof 60hz and a service current of 100A, which follows the safety standards of theresidential facilities.(a) Calculate the maximum power capacity.(b) Within the safety limit, the following devices can all operate at the sametime? If yes, what is the total power consumed? If not, what happens if all devicesare turned on at the same time and suggest a solution to the problem?- 4800W clothes dryer.- 400W washing machine.- 1200W dishwasher.- 1000W iron.- 860W air conditioning.- 150W color television.- 110W stereo sound.- 2400W electric stove.- 1200W microwave oven.- 1800W cooler.(c) Assuming that 60% of the maximum power were used daily, what is the total costper month for a kWh value of 10 cents?(d) Sketch the waveform, determine the phase difference and calculate the rms values of thefollowing waveforms: v(t) = 60 sin(wt + 20) and i(t) = 12 sin(wt - 20).
The resistance and reactance of the single-phase 60Hz transmission line conductors are 8.8 ohm and 10.4 ohm respectively. The transmission line delivers 55MW at a power factor of 0.78 lagging to the load with 50kV receiving end voltage. Determine the following a) The inductance of the transmission line in mH Answer for part 1 b) Sending end power factor Answer for part 2 c) Percentage voltage regulation Answer for part 3 d) Percentage Efficiency Answer for part 4
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Nodal analysis.