For the four-resistor bias circuit shown below, calculate lc (in A) given a value of ß = 172 to 1% accuracy. Assume forward active operation, VBE=0.7 V.20kQ10ΚΩAnswer:wwwB12 Vmm2kQсE1kQ

given here a circuit and asked to find the collector current.

For the four-resistor bias circuit shown below, calculate Ic (in A) given a value of β = 172 to 1% accuracy. Assume forward active operation, VBE=0.7 V. 12 V 20kΩ 10ΚΩ Answer: ww Μ Β 11 Μ 2ΚΩ C E 1ΚΩ

For the four-resistor bias circuit shown below, calculate Ic (in A) given a value of β = 172 to 1% accuracy. Assume forward active operation, VBE=0.7 V. 12 V 20kΩ 10ΚΩ Answer: ww Μ Β 11 Μ 2ΚΩ C E 1ΚΩ

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: 12. In Fig. 27-22, R₁ = 3.00R, the ammeter resistance is zero, and the battery is ideal. What…

Q: es Required information Consider the given circuit, where ZL=100 and R = 100. NOTE: This is a…

Q: 8 Ω 3 8 well Ht Ut 0=1 3Ω 24 V

A: Circuit diagram is given as,

Q: 120 V ww 6Ω www 302 ΖΩ www ΔΩ D 12 Α

A: Circuit diagram is given as,

Q: Q3) A. Explain the working principle of D.C. motors (Electrical energy into mechanical energy) with…

A: Step-1-> Working Principle of DC Motor-: Fleming's Left-Hand Rule, which states that when a…

Q: _25/0° V (+1) 10 Ω www j4Ω Μ 5Ω 1₂ 1/0°Α ell j8 Ω -j6Ω

Q: 165 km three-phase walking line 55 MVA transmits power at 132 kV voltage (in-phase) to the load with…

A: Length of transmission line l=165km, Load SL=55MVA,Vph=132∠0°kV,cosϕ=0.8 lagging, The load current…

Q: + c {=} = √√, find c {√₁}. 9. Given that C (B) √ (C)/√(D) (E)

A: Given data ℒ1t=πs To find out We have to determine the ℒt.

Q: A signal modulated at 2 MHz carrier is described by the ecuación 10 cos (2πfc + 8 cos (6000πt)).…

A: Carrier frequency fc=2 MHz,FM modulated signal sFMt=10cos2πfct+8cos6000πt,Bandwidth B=10 kHz.

Q: (a) Calculate the charge stored on a 3-pF capacitor with 20 V ac (b) Find the energy stored in the…

A: The cpacitor value, C=3 pF The voltage,V=20 V

Q: A linear time-invariant system is described by the difference equation 2 x[n] - x[n 2] - x[n - 4]…

Q: What will be the load current if a 400 Q load is connected in the complicated circuit? RN and IN of…

A: Load is given S = 400 Q. Norton resistance RN=100 Ω. Norton current IN=10 A.

Q: 3.) What is the Voltage Drog что г Resistor ? 120v. ww ww across the 02 800 34022

A: The circuit diagram,

Q: 30/0° V 4Ω www V₁ ell 40/60° V (+ j4Ω V2 -1Ω www 2 Ω

A: In this question we need to find the V1 and V2 in the circuit shown in given Fig.

Q: Q3: Find Io in the circuit of Fig. (3), using mesh analysis method. 560 A 8 Ω -J5 Ω 6Ω J6 Ω 10 60° V…

Q: 1. Consider the circuit of Figure 1 a) Please, use Thévenin's Theorem to determine the Thévenin…

A: For the given circuit the value of open loop voltage needs to be calculated by using the nodal…

Q: Q3) For the control system shown in below. Obtain the closed-loop transfer function C(s)/U(s). where…

A: here we have to find the closed-loop transfer function CsUs

Q: 3) For the given circuit; →Setup state the transition table →Sketch state the satate transition…

Q: Find the total power developed in the circuit in below figure if vo = 10 V? 9A 20 V(+ DO 6A+ + Va -…

A: v0 = 10 V Pdev = ?

Q: elec power generation plant is expected 1st $42,1 complete. The revenues generated by the new plant…

A: Given Cost for the plant = $42,000,000 Revenue generated per year= $3,875,000 Operating Expenses per…

Q: Determine the input impedance of the circuit in Fig. 1 at w=10 rad/s.

A: In this question We need to determine the input impedance Zeq Inductive Reactance XL = wL…

Q: Q5)A continuous-time system has a state space model given by X=¹₁2x+ut y(0-[10]x(t) 2] x(1) 1- Find…

Q: What is the signal corresponding to the following z-transform? (Where u[n] is the unit- step signal)…

A: It is given that: Xz=6z22z-13z-1,13<z<12

Q: A series RLC circuit consists of an 852 resistor, a but capacitor 50 mH inductor as is shown. An…

A: A series RLC circuit is given We need to calculate a) resonant frequency. b) at half resonant…

Q: 2. There is a static machine, built by 2 windings, placed in a magnetic core of S = 15cm2 . N1 = 450…

Q: The Single-phase HW Rectifiers with R, L with free while diode find the value of Voltage and…

A: It is connected in antiparallel with the load RL or RLE. The performance of the rectifier gets…

Q: Question 6 Vx www. R1 Ω Click here for image R20 ww R4 Ω www Gm Vx R3 Ω Find the current I, shown in…

Q: ▪ Question 3. Consider Is it BIBO stable? 10 *-[-]+[J]. x 0 y = [-2 3]x - 2u X u

A: The question is based on the bounded-input bounded-output stability of a system from its state-space…

Q: Q5. Find the answer (in mA) to Question 5 in the attached image where: Vi(min) = 14 Volts, Vi(max)…

A: The above is a voltage regulator circuit using a Zener diode and BJT. We need to find the maximum…

Q: (3): Parallel plate capacitor Q4. A capacitor of initially capacitance 0.08pF is filled with…

A: Given,Initial capacitance, Ci=0.08 pF.and,The table of applied voltage and its charge…

Q: Find vo(t) if Vs = 25cos(50,000t) [V]. Give your answer in time domain. Ο 80 ΚΩ www m 80 ΚΩ {20 ΚΩ…

Q: 8- Set some types of circuit breaker according to quenching media

A: Circuit breakers are electrical devices used to protect electrical circuits from damage caused by…

Q: Consider a signal y(t) = x₁(t) * x₂(t). If x₁ (t) = 2 cos 4t u(t) and x₂(t) = sin 2t u(t). The value…

A: here we have to find the value of y(t) at t=π2 we know that L cosat u(t) =ss2+a2L sinat u(t)…

Q: Perform the following complex number conversions: a) Convert the following complex number to its…

A: here we have to convert the numbers

Q: A proximity switch can be actuated: O without any physical contact. by a change in light intensity.…

Q: 1. (1) To have a "good" resonator, would you like to have a high Q factor or a low Q factor? Explain…

Q: 4. For the two bus power system shown below, use the Newton-Raphson power flow to determine the…

A: Given Data: A two-bus power system with, One slack bus with, V1∠δ1=1∠0° V (By default) One PQ…

Q: The junction temperature in a BJT is 45° Celsius, the ambient temperature or surrounding temperature…

A: To calculate the thermal resistance of the BJT, we need to use the formula: Thermal Resistance (θ)…

Q: 1. Consider an ideal Op-Amp with the inputs of v₁ = 0 V and V12 = 5 V. Label voltages and currents…

A: For the given operational amplifier circuit the value of the voltage at every node needs to be…

Q: Q5: A: 1- What is the transducer and what is used for? 2 What is the difference between temperature…

A: The importance of the transducer needs to be explained and the difference between the temperature…

Q: A digital multiplexer or data selector is a logic circuit that accepts several digital data inputs…

A: According to the question, we need to design a multiplexing system by using 4:1 Mux, and 1:5 Demux.

Q: Determine the N-point DFT of the finite sequence for N≥ (1,0 ≤ n ≤L-1 0, elsewhere x(n) =

Q: 2 3 4 5 6 7 сл Outputs 1 2 4 8 ww mm 8 9 10 11 23 12 13 14 15 However, your first customer has a…

A: Given circuit of encoder: Encoder: A digital encoder is a device that converts a continuous…

Q: does the principle argument in part B, have no 2*n*pi on the end? isn't that worked out with…

A: Does the principle argument in part B, have no 2nπ on the end?

Q: For the following circu

Q: a. Find the poles and zeros b. Find the damping ratio (C), and the natural frequency (w) c. Based on…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 1)The circuit shown below is initially, for t < 0, with capacitor C connected to a battery (Vbat =…

A: The circuit diagram,

Q: formation e circuit given below, where the turns ratio is 21:1. V₁ V₂ G₁ 470 μF RL 1 ΚΩ 1 le in the…

Q: A 480 V, 50 Hz, Y-connected, 4 pole synchronous generator has the OCC shown in the figure 1 below.…

A: Since the question posted by you has multiple sub-parts, we will solve the first three sub-parts for…

Q: 49: Using the following table, design a Binary-to-Gray code converter using k-map to minimize the…

Concept explainers

Types of Thyristors

With four layers of alternating P- and N- materials, a thyristor is a solid-state semiconductor device. It acts as a type of bi-stable switch and it conducts when the gate receives a current trigger and continues to conduct until the voltage is reverse biased across the device or by some means until the voltage is removed. The silicon-controlled rectifier is considered synonymous with thyristors by some sources. Thyristors are defined as more complex by other sources as it contains at least four-layer of alternating N-type and P-type substrate. They find large applications in the control of electrical power supplies, electric motor speed control, and ranging of light dimmers because thyristors can control large amounts of power supplies and voltage with a small device. The circuit symbol of the thyristor is given below.

Question

For the four-resistor bias circuit shown below, calculate lc (in A) given a value of ß = 172 to 1% accuracy. Assume forward active operation, VBE=0.7 V.
20kQ
10ΚΩ
Answer:
www
B
12 V
m
m
2kQ
с
E
1kQ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: current calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A) Design a buck-boost converter with the specifications: Vin = 28 V, in the range [24V,32V], Vout=12 V (with opposite polarity to Vin), load power in the range [0, 120 W], such that to operate in CCM for any line and load value. Select a switching frequency of 100kHz. Choose C= 1.8mF, 25V, 2.5mΩ
COURSE: INDUSTRIAL ELECTRONICS DEGREE: BS ELECTRICAL ENGINEERING For a unijunction transistor with VBB = 20V, n = 0.65, RB1 ✓ 2K-ohms (IE = 0), and VD = 0.7, determine: a) RB2 b) RBB c) VRB1 d) VP
1. For the circuits shown below, if A=∞, Calculate a) The overall input resistance, Rin b) The output resistance, Rout c) Overall voltage gain (vo/vs)
Determine the point Q for the JFET circuit shown and perform the curve transfer showing that point. We have the following data from the different elements of the circuit such as: RG = 10 MΩ, RD = 3.3 kΩ, RS = 780 Ω and powered by a 9 volt source. The manufacturer's sheet indicates that it has IDSS = 4 mA and VP = −6 V. Include transfer characteristic graph.
Vi=20mV , Vcc=15V ,β=110 , r0=30kΩ , Rc=4.7kΩ , RF1=100kΩ , RF2=47kΩ AC source internal resistance Rs = 1.34kΩ , load RL=9,1kΩ output voltage V0 =? Note : Output impedance of transistor r0 must be taken into account in calculations
Attached please find plot of my question regarding Mosfet Transistor. For a Enhancement type MOSFET, it is given as VGS(TH)=VT=3V, k= 0.4x10^−3, rd= 40kΩ. a)Calculate the output voltage (Voutput) for the case where the input voltage is 0.8mV (Vinput = 0.8mV)
Electronic Consider the circuit shown in figure, where be=710 mV, B = 100, and VA = ∞. Assume that the emitter current is equal to collector current. Sekildeki devre için BE=710 mV, B = 100 ve VA = ∞ oldugunu dikkate aliniz. Emiter akiminin kollektör akimina esit oldugunu kabul ediniz. Circuit parameters / Devre Parametreleri Rg = 30 kM, Rc = 400 R, RE = 400 R, Vcc = 4 V -> Alttaki devre için Q, transistörunün kollektor akimini Ic belirleyiniz. (Determine the collector current Ic of Q, for the circuit shown below.) (dogru katsayisi: 0.5) -> Alttaki devre için Q, transistörunün kollektör gerilimini Vc belirleyiniz. (Determine the collector voltage Vc of Q, for the circuit shown below.) (dogru katsays:: 0.5)
Assume the following values for an ADC, with a 8-Bit input:• Clock Frequency = 2 MHz• VT = 0.1 mV• FS Output = 5,12 V2.1. Calculate the Digital Equivalent obtained for VA = 1,52 V;2.2. Calculate the conversion time 2.3. What is the resolution of this converter?
If the circuit of problem 2 is configured as a common-emitter amplifier, calculate the resulting voltage and current gain. Assume a load resistor of 1k ohm. Circuit of problem 2: determine the operating point of a universal trasnsistor DC bias cirucit when Vcc=15V, R1=10k ohm, R2=2.2k ohm, Rc=680 ohm, Re=100 ohm. Assume beta (b)=200 and Vbe=0.72V.
What will be the input impedance value (Zi) of the system since β = 200, Vcc = 20 V, R1 = 47 kΩ, R2 = 6.8 kΩ, RC = 4.7 kΩ, RE = 3.75 kΩ? NOTE: The output impedance r0 of the transistor will be neglected.
ID = 0.0002210600865 [this is the value that I obtained for the operating drain current, kindly recheck] Determine the MAGNITUDE OF VOLTAGE GAIN of amplifier. |AV| = _______ V/V
Estimate the output voltage of a 80W,PV module when it is short circuited? a. 0V b. equal to its Voc value c. less than its Voc value d. more than its Voc value Clear my choice