For the gravity concrete dam shown in the figure, the following data are available:- The factor of safety against sliding (F.S sliding) =1.23Unit weight of concrete (Yconc) = 24 KN/m- Neglect( Wave pressure, silt pressure, ice force and earth quake force)μ = 0.65, (Ywater) = 9.81 KN/m³Find factor of safety against overturning (F.S overturning)6m180m10m5m+

Answered: Image /qna-images/answer/df2837b5-0e43-4bac-94dc-cfef7a6d3c61.jpg

For the gravity concrete dam shown in the figure, the following data are available: The factor of safety against sliding (F.S sliding) =1.2 - Unit weight of concrete (Yconc) = 24 KN/m³ - Neglect( Wave pressure, silt pressure, ice force and earth quake force) μ = 0.65, (Ywater) = 9.81 KN/m³ Find factor of safety against overturning (F.S overturning) 10m 6m1 5m Th 80m k X

For the gravity concrete dam shown in the figure, the following data are available: The factor of safety against sliding (F.S sliding) =1.2 - Unit weight of concrete (Yconc) = 24 KN/m³ - Neglect( Wave pressure, silt pressure, ice force and earth quake force) μ = 0.65, (Ywater) = 9.81 KN/m³ Find factor of safety against overturning (F.S overturning) 10m 6m1 5m Th 80m k X

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.12P

See similar textbooks

Similar questions

A concrete dam retaining water is shown in the picture. If the specific weight of concrete is 23.5 kN/m3 , 1. what is the total hydrostatic force? 2. Find the maximum intensity of pressure? 3. What is the factor of safety against overturning? 4. Find the factor of safety against sliding if the coefficient of friction is 0.50? 5. Find the resultant force? 6. Find the location of the resultant? 7. Determine the minimum intansity of pressure?
varies uniformly from full Hyu between dam and foundation soil is 0.40. Which of the following most nearly gives the factor of safety against slidling? 12 m A. 1.22 1 m 5m A. 2.56 4m 9m A. 154.52 kPa 4m 2 m 8m 3m B. 1.56 7.) A concrete dam retaining water is shown in the figure. The specific weight of concrete is 24 kN/m3. Assume hydrostatic uplift varies uniformly from full hydrostatic pressure at the heel of the dam to zero at the toe and that the coefficient of friction between dam and foundation soil is 0.40. Determine the factor of safety against overturning. C. 2.31 B. 315.61 kPa C. 2.12 B. 1.89 8.) A concrete dam retaining water is shown in the figure. The specific weight of concrete is 24 kN/m3. Assume hydrostatic uplift varies uniformly from full hydrostatic pressure at the heel of the dam to zero at the toe and that the coefficient of friction between dam and foundation soil is 0.40. Determine the maximum pressure on the foundation. D. 1.89 C. 281.63 kPa D. 3.14 D. 241.89 kPa
Bleopage is assumed to occur beneath the concrete wall producing a finear distribution of hydrostatic pressure, as shown in Figure 1). Suppose that a-9 ft and b-12 ft. Figure 1 of 1 > Determine the location of the vertical resultant force due to seepage. Express your answer to three significant figures and include the appropriate units. 2p= Submit Part D UPM Value Submit Request Answer Determine the p-location of the horizontal resultant force due to pressure of water to the loft of the wall. Express your answer to three significant figures and include the appropriate units #A Value Units Request Answer Units
Consider the following data regarding a theoretical profile of a dam: Permissible value of compressible stress o = 350 tonnes/m², Specific gravity of concrete, s = 2.4, Uplift coefficient, c = 0.6 m, The value of y=1 ton/m³ What is the height of base width.
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).
Q5: For the gravity dam shown in the figure, the following data are available: - Unit weight of concrete (ycone)=2.4 ton/m - Vertical upward earthquake factor (Kv) = 0.1 - Neglect Wave pressure, Silt pressure, and Ice force. - Use u=0.7 10m 6m What will be the value of the heel and toe stresses 82m 80m (Pmin & Pmax)?
Q: You have been assigned to check the stability of a pond constructed in stiff saturated clay underlain by a layer of sand. The necessary information are given in the following figure. (i) Find effective stress at A and determine the stability of cut under given condition. (ii) What should be water level into the pond to ensure factor of safety = 1.5. (Given that yw = 9.81 kN/m³) H = 5 m 7m 2m 2m J Saturated clay Sand Ysat = 16 kN/m³ 4m Ysat = 15 kN/m³
Datasheet for consolidation test Load,kN/m? Dail reading &H=dail reading*0.01mm 25 27 0.27 50 46 0.46 100 72.3 0.723 200 101.5 1015 400 135 1.35 800 186.9 1.869 200 169.9 1.699 50 149.5 1.495 Find: 1.The coefficient of volume compressibility, m, 2. Compression index, C, 3. Preconsolidation load, P, 4. The coefficient of consolidation, c,
A concrete dam is triangular in cross section and 30m high from the horizontal base. If water reaches adepth of 27 m on the vertical face, what is theminimum length of the base of the dam such thatthe resultant will intersect the base within themiddle third? What minimum coefficient of frictionis required to prevent sliding? Determine thepressure distribution along the base. Unit weight of concrete and masonry is 23.54 kN/m3 NOTE: CLEAR HANDWRITTEN SOLUTION
Figure Q2 shows a reinforced concrete platform with a cantilever slab and wall at the edge of slab. The brick wall is seated on the edge of cantilever slab is 3.2 m high. Given: All slab thickness = 150 mm All beams = 250 mm × 600 mm Concrete unit weight = 25 kN/m3Weight of brickwall = 2.6 kN/m2Finishes = 1.5 kN/m2Variable action = 5 kN/m2 Determine the characteristic permanent action (gk in kN/m) and variable action (qk in kN/m) acting on Beam B/1-2.
A building is founded on a rectangular mat of dimensions 20 m x 10 m as shown in the plan view in figure below. A surcharge of 300 kPa is applied within the area ABCD whereas a surcharge of 100 kPa is applied within the area CDEF. Calculate the increase in vertical total stress in kPa at the depth of 5 m below Point F
EARTHQUAKE ENGINEERING PROBLEM: A five storey building has a moment-resisting steel frame for a lateral force-resisting system. The following data are available for the location of the building in zone 4: I=1.0 Seismic Source Type=A Soil Profile Type=Sc Distance from nearest fault=25 km 1. What is the value of design base shear in kN? Use NSCP 2015. 2. What is the value of lateral force in kN at the top? Use NSCP 2015.