For the loaded beam shown, using moment - area method. a. Determine the value of El6 at mid span and under the concentrated load t b. Determine the deflection at mid span and under the concentrated load Use = 200 GPa and l=65.0x106 mm4. 24 kN 18 kN/m B -1.5 m--1.5 m- - 3 m

For the loaded beam shown, using moment - area method. a. Determine the value of El6 at mid span and under the concentrated load t b. Determine the deflection at mid span and under the concentrated load Use = 200 GPa and l=65.0x106 mm4. 24 kN 18 kN/m B -1.5 m--1.5 m- - 3 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the force in members CDof the truss in kN and state if the members are in tension or…

A: ASKED: To determine the force in member CD of the given truss and state the nature of the force.…

Q: An earthquake is a rapid and successive tremors or tremors of the earth's crust as a result of the…

A: Correct As an earthquake occurs whenever the enrgy stored in rock is suddenly released.

Q: A soil sample is collected under the ground water level, what is the void ratio if given the…

A: Asked: To compute the void ratio of the soil. Given: Specific gravity of the soil solids (Gs) =…

Q: 2 A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: An earthquake is a rapid and successive tremors or tremors of the earth's crust as a result of the…

A: Correct As an earthquake occurs when energy stored in rock is suddenly released.

Q: If safety is really important, then why most construction workers we have in the country did not go…

A: Yes, Safety is really important. Below has the explanation

Q: What is the reaction at A in kN? Replace the distributed loading by an equivalent resultant force…

Q: Two observers 200' apart recorded the travel times of 3 vehicles as follows: Vehl 1 = 5 sec, Veh 2 =…

A: step 1-

Q: The thickness of the capillary property band is larger in the case of It is formed from fine-grained…

A: Right. The height of capillary rise in the sediments in fine grained sediments is more than that in…

Q: A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear…

A: step 1-

Q: III – Moment Area Method 3. Using the moment area method, determine the deflection yc at point C. EI…

A: Using moment area method find deflection at C.

Q: SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25…

Q: calculate centroid

A: Given: A section To find: Centroid

Q: Which among the formulas below can be used to compute the combined stress at the bottom fiber of a…

Q: if a 250mm sewer is placed on a slope of 0.010, a. what is the flowing capacity when n=0.013…

A: Given data Dia of pipe = 250 mm Manning constant = 0.014 Slope = 0.010

Q: Problem Determine the level of service? for six lanes undivided level highway. The width of lane,…

A: FFS = BFFS - flw - flc - fm - fa BFFS = Base FFS = 55 mph flw = Adjustment for lane width = 10 ft =…

Q: Q.2. What are the various importance of errors in surveying ?

A: Importance of errors in surveying

Q: On the basis of arch-rib analysis, design an arch dam 137m high to span 226m wide U- shaped canyon.…

A: Given data:- Height of arch dam h = 137 m Length of arch dam L = 226 m Allowable compressive stress…

Q: A soil sample is collected under the ground water level, what is the voi ratio if given the specific…

Q: of 0.70, degree of saturation 50% and G. =2. ensity. By how much can the water content

Q: A piece of wood floats in water with 15cm projecting above the water surface. When placed in oil,…

Q: A power-controlled model plane takes off with constant acceleration. If it requires a distance S = 4…

Q: A restrained beam having a span of 5 m is loaded with a distributed load that varies from 12kN/m on…

A: Question is solved using double integration method. As each method is lengthy, so please post…

Q: Determine the specific gravity of combir tical specific gravity of 2.4. The bitumen cor 0.

Q: ESSAY Advantages and Disadvantages of Using Hollow Block

A: Hollow blocks are generally prepared with aerated concrete . These block have both advantages as…

Q: Solve for the reaction at D.

Q: A rectangular log of wood is floating in water with a load of 100 N at its centre. The maximum shear…

A: Given: Rectangular wood floating with load of 100 N at its centre To find: maximum shear force in…

Q: 7. ASTM suggests a tolerance of .. water. A. 12 percent to allow the variation in strength as a test…

A: ASTM suggest a tolerance of 8% to allow the variation in strength as a test of water. It means if we…

Q: A water (Temperature = 20 °C) is flowing in a commercial steel pipe at a lowrate of 5 m³/s. The…

A: step 1-

Q: What is the moment reaction at A in kN.m? Solve for the support reaction of the beam shown in the…

Q: •213. The rigid bar AB, attached to two vertical rods as shown in the figure, is horizontal before…

Q: effective stress for the soll at point A

A: Given: To find: Effective stress at A

Q: For the beam loaded as shown in the figure. determine the following unknowns using shear and moment…

A: Draw SFD and BMD and find maximum shear force and bending moment?

Q: : The following plot represents the grain size distribution curves for soils 1. 2 and 3. You are…

Q: identify and discuss factors that influencr well-being and life satisfaction.

A: Wellbeing: It is a complex one which is relates with both physical and mental emotions of a Human.…

Q: What is the reaction at A in kN? Replace the distributed loading by an equivalent resultant force…

A: Determine support reactions for given loaded beam.

Q: L= 450 feet g1 =-3.00% 92 = +1.50% VPI station = 66 + 50 VPI elevation = 560.00 feet Station giX (in…

A: BVCSTATION=VPISTA-L2BVCSTATION=6650-4502=64+25BVCELV=PVIELV-g1L2BVCelv=560+0.03×4502BVCelv=566.75ft

Q: Answer the situational problem. At a certain section of a river the left and right water edges are…

A: According to Answering guidelines ,if number of questions isn't indicated, the primary inquiry or…

Q: Phe beam below 40KN Draw the Sf and BM digean 5m 5m 5m

A: To draw the SFD and BMD

Q: Design a canal having a trapezoidal cross section to carry a design discharge of irrigation water of…

Q: Find the Reactions

A: For the given beams with loadings, the reactions are to be determined.

Q: A trapezoidal channel carry water at a rate equal to 10 m?/sec, Manning's n is 0.02 and bed slope is…

Q: Solve for the acceleration of block X in m/s2

Q: case of a rectangular channel 3 m wide and 1 m deep, the value of Bazin's constant is 1.75 for…

Q: 1. A 520mm-diameter pipe leaves a straight 380mm-diameter pipe at point A and later joins it again…

Q: A 800ft vertical curve has its PVI at elevation 304.25ft. The initial and final grades are 2.4% and…

A: L = 800ft YPVI = 304.25ft n1= 2.4% n2= -2.2% It has been asked in the question to determine the…

Q: SFD and BMD

A: Given: Cantilever Beam with Uniformly Distributed load at free end W= 22 N/m…

Q: water flows in a trapezoidal channel 3m wide and has a side slope of 1 vertical to 2 horizontal. the…

Q: A net load Q was applied on a rectangular flexible foundation. A point P is located inside the…

Q: Transverse seismic waves (S-waves) do not penetrate the materials of the Earth's interior that are…

A: Explanation : The transverse seismic shear waves i.e. S- waves travel in shearing motion as the…

Question

Please solve for the engineering problem below as soon as possible. Show your complete solutions and include shear and moment diagrams.

Item 2 of 2
For the loaded beam shown, using moment - area method.
a. Determine the value of El8 at mid span and under the concentrated load t
b. Determine the deflection at mid span and under the concentrated load
Use = 200 GPa and l=65.0x106 mm4.
%3D
24 kN
18 kN/m
A
B
–1.5 m--1.5 m-
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step by step

Solved in 9 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)
compute the slope and deflection at B and E of the beam and loadings shown using area-moment method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. E=20GPa. (point B is not an internal hinge).
Determine the slope at point A and the deflection at point C of the beam shown by the conjugate-beam method. 180 KN -3 m- B 3 m- Hinge C I=2080 x 106 mm² D -3 m————5 m- E E = 200 GPa I= 1040x106 mm² 67.5 kl -3 m- F
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
A 6m simply supported beam AB carries 2 concentrated downward loads of P=26KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the maximum deflection of the beam? Express your answer in "mm" in 2 decimal places. Include (-) negative sign if deflection is downward.
For the beam and loading shown, use discontinuity functions to compute:(a) the deflection vA of the beam at A, and(b) the deflection vmidspan of the beam at midspan (i.e., x = 2.4 m).Assume a constant value of EI = 1590 kN-m2 for the beam; MA = 8.5 kN-m, w0 = 19.8 kN/m, LAB = 1 m, LBC = 2.8 m.
A continuous beam ABC has fixed supports. Constant value of El and using slope deflection method. What is the moment MAB in KN-m? 2 decimal places
Find the slope and deflection at B and E of the beam and loadings shown using unit load method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. E=20GPa. (point B is not an internal hinge. clue:YE=0.08 mm, θE=8.07 X 10^−6 rad, θb=2.04 X 10^−6 rad, Yb =0.00278 mm).
A cantilever beam carries a trapezoidaldistributed load (see figure). Let wB = 2.5 kN/m,wA = 5.0 kN/m, and L = 2.5 m. The beam has amodulus E = 45GPa and a rectangular cross sectionwith width b = 200 mm and depth h = 300 mm.Use the method of superposition and Cases 1 and8 in Table H-1 to calculate the def lection and rotationat B.
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
Find the slope and deflection at B and E of the beam and loadings shown using area-moment method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. E=20GPa. (point B is not an internal hinge).
Fixed end support at A and rollers at B and C . A concentrated load of 12 KN at the mid span of BC.Use slope deflection method and constant value of El with E= 200,000 MPa and 1= 400 x 106 mm^4. What is the moment MBC and MABin KN-m? 2 decimal places