Determine the head loss in meters in PIPE 1.Determine the head loss in meters in PIPE 5.Determine the velocity of flow in the lower branch, PIPE 3, in meters persecond. For the pipe network shown, the flow of water from A to the first junction is0.055 cubic meter per second. Assuming all pipes have a roughness coefficientof 0.014,L2 D₂PipeLength, mDiameter, mme₂1300202.72150202.7LI DI720.014375202.7Q₁4300381.05450303.2L4 D4Q4Q5

The given figure shows the pipe system It is required to find out the head loss in meters in PIPE…

Answered: Determine the head loss in meters in…

Determine the head loss in meters in PIPE 1. Determine the head loss in meters in PIPE 5. Determine the velocity of flow in the lower branch, PIPE 3, in meters per second.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Superposition Problem 4. Draw the moment diagram for the beam using method of superposition.

A: Drawing of moment diagram for beam using method of super position

Q: For the beam loaded as shown, by conjugate-beam method (CBM). Determine the slope and defled at…

A: Given data:

Q: 1. Sand cone equipment is used to determine an in-place unit weight (field density test) on a…

Q: A 2 km pipe of 0.2 m diameter connects two reservoirs. The difference between the water levels in…

Q: A vertical steel rod is fixed at the top and supports an 8-kN load at the lower end. The rod is 10…

A: Given data: P = 8 KN D= 10 mm = 0.01 m L = 25 m γ = 77 KN/m3 E = 200 x 109 N/m2

Q: A 30m high steel chimney has the trefoil cross-section shown in Figure 2, consisting of three welded…

Q: Locate the centroid for the following areas :

A: To find the centroid of shaded region

Q: Yg Z.. 200 mm ly G 20 mm 20 mm 200 mm

Q: 9.12 Water flows past a flat plate that is orient with an upstream velocity of 0.5 m/s. Determ…

Q: The bolt shown in figure is subjected to a total tensile force of 90 kN. Determine the tensile…

A: Given: The tensile force is 90 kN. Consider the figure,

Q: determine the sign and magnitude of (a) the slope at end A, (b) the deflection at end A (use method…

Q: Find T(t) and N(t) at the given point. r(t) = 5 cos(t)i + 5 sin(t)j + tk; t = 2 T(₁7) = (π) =

Q: Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the…

Q: For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.4…

A: To find deflection at H

Q: What exactly is computer-aided design (CAD)?

A: Computer aided design is main component of design of structures in Engineering.

Q: 9.48 Water flows past a triangular flat plate oriented parallel to the free stream as shown in Fig.…

Q: Find roller support reaction

A: Given data : The value of Point load P=5 kip The value of point load Q=5 kip The value of Moment…

Q: Topic: Flow in closed conduits For the pipe network shown, the flow of water from A to the first…

A: solution Given the flow in the closed conduits as the friction gactor in all pipes is given as…

Q: Why is it that civil engineers shall approve or seal only plans and design documents reviewed or…

A: It's an topic of ethics. Engineers should follow the ethics to ensure the safety and welfare of…

Q: 9.47 If the drag on one side of a flat plate parallel to the upstream flow is when the upstream…

A: Force due to drag is FD=CD(12ρAU2)CD=1.32δReCD=1.32δUlμso,FD=(1.32δUlμ)(12ρAU2)FD∝U32

Q: 50 mm www. 001 wmOSI

A: step 1-

Q: Question 38 The steel framework shown below is used to support the reinforced concrete slab (unit…

A: Solution: Given: Unit weight of concrete = 23.6 kN/m3, Live Load = 2.4 kPa Slab thickness = 150 mm…

Q: construction project, the field moist unit weight was 115 lb/ft³ at a moisture content of 8%. If the…

Q: For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 6.9…

A: Given data EI = 6.9 × 104 KNm2 Find , deflection at H (VH) Lets using superposition method

Q: Water from a reservoir is pumped all over a hill through a pipe 1 m in diameter. A pressure of 20…

Q: Determine load requirements for LM1 for loaded length 35m, assume the carriage width of 10m

A: Given Data: Length = 35m Carriage width = 10m

Q: find all reaction for the frame shown by The slope deflaction method B hinge с Fin 2 WL 12 3 3 find…

A: Fixed End Moments

Q: 1. Investigate the adequacy of 2-45x45x6 mm angles back to back to be used as top and bottom chord…

A: Given, Loads, P1=20 kNP2=30 kNP3=25 kN Gusset plate t=8 mm Rivet diameter d=20 mm

Q: In a building construction site, temporary structures and connections are needed. Identify the…

A: Temporary structures and connections are made during building construction to facilitate the…

Q: K-4) Apply the Stiffness Method to determine the reactions at supports. Draw the internal force…

Q: A 2 km pipe of 0.2 m diameter connects two reservoirs. The difference between the water levels in…

A: Calculate the velocity in the pipe,V=?

Q: A cantilever beam having a span L of 12 m. carries a concentrated load W of 25 kN at midspan. Assume…

Q: The beam shown below will be subjected to a concentrated live load of 100 kN, a uniformly…

Q: Locate the centroid for the following areas :

A: To locate the centroid of the area

Q: Question-4: An open layer (doubly drained) of clay 4 m thick is subjected to loading that increases…

A: step 1-

Q: A 3-inch diameter pipe is connected to a 4-inch diameter pipe. If the velocity of flow in the…

A: step 1-

Q: "| A Answer: VC= W LAB m mm. LBC P X

Q: Calculate the side resistance in pounds for 20 ft long open ended 27 inch diameter smooth steel pipe…

Q: predicted to be 0.21. TE Determine the aerodyn through still air at 55

Q: (a) Determine maximum tensile stress in the beam (b) Determine maximum compressive stress (c)…

Q: Locate the centroid for the following areas :

A: To find the centroid of shaded region

Q: During a test on a 245 cm long rectangular suppressed weir which was 100 cm high, the head was…

Q: 1. Determination 2. Determination of Normal Consistency Of Hydraulic Cement of Setting Time of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: g at 4 m/s through water. Estimate the por of the log is parallel to the tow direction

A: νw=1.12×10-6m2sρw=998.8kgm3Re=vDν=4×21.12×10-6=7.14×106so,Aspect ratio =LD=82=4For circular ract…

Q: Analyse the rectangular two way slab for the yield pattern -1 (as shown below) by equilibrium…

Q: C The Expressions For The Steady-state Voltage And C... | Chegg.com Syllabus Scores Text Study Area…

Q: II. Method of Superposition Problem 4. Draw the moment diagram for the beam using method of…

A: Bending moment at a section can be found be superimposing(adding) the bending moments due to the two…

Q: T1. Water is to be pumped from a reservoir at datum level 6.5m to a reservoir at datum level 24.8m…

Q: a) Determine the vertical reaction at support A. 8 k/ft 4 k/ft .…………. A B 30 ft

Q: If the shear stress at an angle of 56 degrees through the cross section of a timber beam (width 46…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

Determine the head loss in meters in PIPE 1. Determine the head loss in meters in PIPE 5. Determine the velocity of flow in the lower branch, PIPE 3, in meters per second.

For the pipe network shown, the flow of water from A to the first junction is
0.055 cubic meter per second. Assuming all pipes have a roughness coefficient
of 0.014,
L2 D₂
Pipe
Length, m
Diameter, mm
e₂
1
300
202.7
2
150
202.7
LI DI
720.014
3
75
202.7
Q₁
4
300
381.0
5
450
303.2
L4 D4
Q4
Q5

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A new cast iron pipe must carry 1.2 m3/2 at a head loss of 5m per km length of the pipe. Compute the diameter of the pipe in mm using f=0.029 Group of answer choices 928.44 428.94 284.94 892.44
A 750mm dia. pipe 1162m long carrying 2.4 cubic meter per second of water branches into two pipes, 450mm dia. and 600mm dia. at junction A. The 450mm pipe is 1254m long and the 600mm is 1196m long. They come together at junction B and continue as a single pipe 750mm in diameter and 866m long. Assuming the values of fare 0.017, 0.019, and 0.020 respectively for the 750mm, 600mm, and 450mm pipes. What is the discharge in the 450mm pipe?
The bottom width of a trapezoidal canal is 2.5 m and its sides are both inclined at 60° with the horizontal. Water flows at a depth of 3 m. Find the discharge in m³/s if S = 0.0008 and n = 0.03. Use the Kutter’s formula. * a. 14.76 b. 17.76 c. 15.76 d. 16.76
In the branched pipe system below, water is flowing at 0.0142 m3/sin a new, clean DN 100 Schedule 40 pipe (ID = 0.1023 m) at A. The flow splits into two new, clean DN 50 Schedule 40 pipes (ID = 0.0525 m; A = 0.00216 m2) as shown and then rejoins at B. Call the 30 m branch“a” and the other branch “b.” The friction factor in Branch ais 0.021, and the friction factor in Branch bis 0.0215.(Note that if friction factors weren’t given, you’d need to make initial guesses and iterate!)Calculate the flow rate in each of the branches. Include the effect of all minor losses in Branch bbut ignore the tee junctions. The total length of the pipe inBranch bis 60 m. The elbows are standard.(Remember to check that your final answers follow continuity!)
Fluid mechanics Water flows in a 15-in. diameter full-flowing cast-iron pipe. The friction slope is 0.00640 ft/ft. Find the discharge in units of gpm (gallons per minute) and cfs (cubic feet per second). Use the equation Q = 0.279CD2.63S0.54
Hydraulic structure Q.2: Given the following data of a head regulator: The discharge= 60 cumecs, bed level of the canal-52.2m, crest level of the regulator=52.8m, upstream water level-54.2m, downstream water level=53.9m. The dimension of gates= (2.5x3)m and the thickness of the piers is 0.9m. Neglect the velocity head and use coefficients of discharge= 0.8 and 0.577. Determine the water way of the regulator
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f=0.019. Determine the flow rate in lit/sec. a. 522.88 b.885.22 c. 228.55 d. 822.55
PROBLEM 03: Glycerine (SG = 1.26) flows through a pipe AB 48" in diameter at 10 fps and then passes through a pipe BC which is 60" in diameter. At C the pipe forks. Branch CD is 32" in diameter and carries one-third of the flow in AB. The velocity in branch CE is 8fps. Find the the diameter of CE in inches.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f=0.019. Determine the head loss in meters choices: 7.52 2.75 5.27 7.25 Determine the flow rate in lit/sec choices: 822.55 885.22 228.55 522.88
4. Find the approximate flow rate at which water will flow in a conduit shaped in the form of an equilateral triangle if the head lost is 6m per km length. The cross‐sectional area of the duct is 0.075?2 . Assume f = 0.0155.