For this Differential Amplifier Circuit, assume 3 of both transistors is very high. Find the value of Vin2 for which the current flowing through 4 k resistor of Q2 is 2 mA. (Assume VT = 25 mV). чка Vin 1 = 2V WW Q₁ Vo, P 24V Voz €4k52 кл +4mA Q₂ Vin 2

For this Differential Amplifier Circuit, assume 3 of both transistors is very high. Find the value of Vin2 for which the current flowing through 4 k resistor of Q2 is 2 mA. (Assume VT = 25 mV). чка Vin 1 = 2V WW Q₁ Vo, P 24V Voz €4k52 кл +4mA Q₂ Vin 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: QUESTION 4 For an n-channel Junction Field-Effect Transistor (JFET), the gate-source cut-off…

Q: 0.038 +0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: In star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current, IPh…

Q: OR e) Explain the following protection schemes of alternators. i) Stator inter turn protection. ii)…

Q: A 188 KW, 200 volt, three phase, delta-connected induction motor has a full load efficiency of 94 %…

A: Given data, Output Power (Pout)=188kW Line Voltage (VL)=200V Full load efficiency ηfl=94% or 0.98…

Q: (c) A solar farm contains 300 modules each with an active area of 1 m² and generates 30 kW of power.…

A: Utilization factor: Utilization factor is also known as the use factor where the time used by…

Q: 16. The resistance of a parallel circuit consisting of two branches is 12 ohms. If the resistance of…

A: Given: Resistance of two branches parallel circuit, Req=12 Ω Resistance of one branch, R1=18 Ω…

Q: 9.10 The loss formula coefficient matrix for a two-pla system is given by 0.001 -0.0001 -0.0001…

A: Given, The loss formula coefficient matrix for a two plant system, B=0.001-0.0001-0.00010.0013 MW-1…

Q: Using the practical diode model, the current in the circuit shown is A 1.89 mA 12 V Si Si B 5.6kΩ·…

A: Given circuit:

Q: The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN…

A: Given data, A 3/0 THWN copper conductors at 480 V Length, L=248' Load current, I=180 A

Q: 1. a) What is the amplification ratio (expressed in dB) of a DC amplifier with input DC voltage of…

A: 1. a) The amplification ratio is given by the expression as shown below: Av=VoutVinVout=10 VVin=100…

Q: In the circuit shown, switch S₁ is closed at t = 0 and switch S₂ is opened at t = 0.2 second. Find…

Q: (a) Explain the advantages and disadvantages (in 4-5 sentences or a bulleted list) of using a direct…

A: EXPLAIN: The advantages and disadvantages of using a direct mapped cache instead of an 8-way set…

Q: (4) Consider an FM signal given by the expression f(t) = cos[2nfet + ß₁ sin(2πf₁t) + B₂ sin(27f₂t)].…

A: Frequency modulation :- It is a technique that encodes information on particular signal by changing…

Q: Half Wave diode rectifier circuit consists of Select one: O a. Two diode in Parallel with RL O b.…

Q: : Differentiate between Lightening arrester and lightening conductor?

A: Differentiate between Lightening arrester and lightening conductor: Lightning conductor: A lightning…

Q: Discuss advantages of per units representation

A: Advantages of per unit representation

Q: In a short circuit test on 132 kV, 3-phase system, the breaker gives the following results: Power…

Q: Q1 The following differential equation describes a water tank system d h(1) +/h(1)=9,(1) dt AR where…

A: 1) Given a differential equation describing a water tank system a) Write the differential equation…

Q: D1 RL Vdd = +6 V Lund VF VL Figure 1-2.b 6000 6000

A: If the diode is open then we take the node voltages of that two open nodes to calculate the voltage…

Q: R 8១ រ = — ja

A: Curcuit behave like resistive at resonances condition Total inductive reactance equal to total…

Q: In Fig. 39.16, what is the feedback fraction m₂? (1) 0.01 (iii) 0.04 (ii) 0.02 (iv) 0.05 Vin 2 μV…

A: Given feedback amplifier circuit:

Q: A single-phase half-controlled rectifier supplies a 220 V, 1200 RPM, 10 A rated DC motor from a 220…

A: Single-phase half-controlled rectifier: It converts AC input to DC output and controlled means that…

Q: ^ what is 200121° Urm 2001-95° Urms 200 1145 Vrms 4 3 IL1 I. k 2a 26 Zc N 2a= 2b = 2c= (25+j5) e…

A: In this question, We need to determine the complex power, active power and reactive power?. We…

Q: to c correct the errors that can occur when the data is moved or stored from t to the receiver.…

A: (i) The number of message bit(m) is 16. To find parity bits(p) we use the formula as Given m=16,…

Q: What are the Various type of faults in transformer

A: There are various type of faults in transformer which is given below- Overheating Overheating is…

Q: The voltage of an electromagnetic wave propagating in a coaxial cable with uniform characteristic…

A: The propagation constant for a transmission line is given as: γ=α+jβ α is the attenuation constant…

Q: A 25 KVA transformer supplies a load of 12 kW with a power factor of 0.6 lagging. Find the…

Q: 1. Find the out the prime and essential prime implicants for the following Boolean functions. Write…

A: Boolean expression- A Boolean expression is the expression that evaluates to either TRUE or FALSE…

Q: Find out i) Input impedance function and ii) V0(s)/Vin(s) for the network shown in the Fig

A: The input impedance and transfer function of the circuit can be obtained by converting the circuit…

Q: 5. The total charge entering a terminal is given by q = 5t sin 4πt mC. Calculate the current at t =…

A: Given, Total charge entering a terminal is given by q=5tsin4πt mC Time, t=0.5 s

Q: What is the frequency of oscillation for RC phase shift oscillator with R = 10 kn and C= 0.001 µF in…

A: Given, A RC phase shift oscillator with each resistor and capacitor has R=10 kΩC=0.001 μF

Q: 0.038 +/0.072 f/phase. Calculate the line-to-line source volt- age magnitude required so that the…

A: For Star connection, Line voltage, VL = 3 * Phase voltage, VPh Line current, IL = Phase current,…

Q: A 100 KVA transformer is at 80% of full-load with power factor of 0.85 lagging. What KVA of load of…

Q: In order to light a LED: send a HIGH signal and this will be written in the Loop function send a LOW…

A: If we want to light a LED which condition will satisfy : send a HIGH signal and this will be…

Q: A flow transmitter has an input range of 40 gallons per minute (GPM) to 130 GPM, using a standard…

Q: In the circuit shown, Find the value of the resistor R, for I = 75 mA. 510 52 Select one: O a. 1530…

A: Given circuit: I=75 Ω

Q: find the steady-state response,

Q: The circuit shows a variable resistor, with a lamp (L) connected to an ammeter and a voltmeter. By…

Q: sing Kirchoff's law, calculate each current: 11, 12 and (11-12) in the following electronic ircuit:…

Q: 13.78 currents in the circuit of Fig. 13.140. 1+ 100/30° V (+ 20 Ω I₁ j80 Ω determine the mesh 40 Ω…

Q: g(t) = 10cos (150xt+) Find the fundamental period and fundamental frequency of g(t). The fundamental…

A: Given data, Function gt=10cos150πt+π4

Q: An impulse generator has eight stages with each condenser rated for 0.16 µF and 125 kV. The load…

Q: A data stream of 60 Mbps is to be transmitted through a wireless channel using 64-QAM technique.…

A: Given, A data stream of, Rb=60 Mbps Transmitted through a wireless channel using, M = 64 - QAM

Q: Calculate the form factor and peak factor of a triangular wave in which the voltage rises uniformly…

A: Form factor: It is the ratio of the RMS value and average value. It gives information about the…

Q: An inductance a capacitance connected in parallel across a A OA 50 V, 50 Hz supply. The current…

A: Given: Inductive reactance, XL=4 Ω Inductive capacitance, XC=4 Ω Both are connected in parallel…

Q: 9. If the output voltage of an amplifier is 1.2 V rms and its voltage gain is 50, what is the rms…

A: Given: Output voltage, V0=1.2 V Voltage gain, Av=50

Q: 4. The amplitude spectrum of the signal x(t) is shown as follows: | X()| 2 A -3500 -3450 -2000 0…

Q: Evaluate various possible impulse responses h(t) from the transfer fun Q1(b), considering the…

A: Solution- xt=δt →Impulse signalh(t) = wt →Impulse responsey(t) → o/p from the figure, ωt…

Q: x [n] 5-4-3 -4-3-2 3 2 1 -2 U (a) 12 9.2. The discrete-time signals in Figure P9.2 are zero except…

Q: 6 (2) Find and draw the Fourier transform of f(t) = 9+t²

Concept explainers

Differential amplifier

There are two amplifying stages with common degeneration in a differential amplifier.

Question

For this Differential Amplifier Circuit,
assume 3 of both transistors is very high.
Find the value of Vin2 for which the
current flowing through 4 k resistor of
Q2 is 2 mA. (Assume VT = 25 mV).
чка
Vin 1 = 2V
MW
Vo,
P 24V
Voz
€4k52
кл
Q₂
4mA
O
Vin 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

(a) What are the Q-points for the transistors in the amplifier as shown if VDD = 9 V, VSS = 9 V, ISS = 40 μA, RSS = 1.25 MΩ, and RD = 300 kΩ? Assume Kp = 200 μA/V2, γ = 0.6 V0.5, 2φF = 0.6 V, and VTO = −1 V. (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-mode input resistances?
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
(a) What are the Q-points for the transistors in the amplifier as shown if VDD = 12V, VSS = 12V, ISS = 1.5 mA, RSS = 33 kΩ, and RD = 15 kΩ? Assume Kn = 375 μA/V2 and VT N = 0.75 V. (b) What are the differential-mode gain, commonmode gain, CMRR, and differential-mode and common-mode input resistances?
(a) What are the Q-points of the transistors in the amplifier as shown if VCC = 22 V, VEE = 22 V, I1 = 200 μA, RE = 2.4 kΩ, R = 50 kΩ, βo = 80, and VA = 70 V? (b) What are the differential-mode voltage gain and input resistance? (c) What is the amplifier output resistance? (d) What is the common-mode input resistance? (e) Which terminal is the noninverting input? (f) What is thecommon-mode input range for the amplifier if current source I1 is replaced with an electronic current source that must have 0.75 V across it to operateproperly?
The ac equivalent circuit for an amplifier is shown . Assume the capacitors have infinite value, RI = 750 Ω, RB = 100 kΩ, RC = 62 kΩ, and R3 = 100 kΩ. Calculate the voltage gain and input resistance for the amplifier if the BJT Q-point is (40μA, 10 V). Assume βo = 100 and VA = 75V.
(a)What are Add and Acd for the bipolar differential ampliﬁer shown(RL =∞) if βop =70, βon = 125, IEE = 50 μA, REE = 100 MΩ, VA = 75 V and the Early voltages for both transistors are 60 V? What is the CMRR for vC1 = vC2?(b) Repeat part (a) for VA =100 V.
Given the differential amplifier circuit, (a) Determine hie1 and hie2.(b) Determine the common-mode rejection ratio CMRR for single-ended output.(c) Determine the single-ended output Vo2 if Vs1=10mV and Vs2= Vs1.(d) Determine the double-ended output Vout if Vs1=10mV and Vs2= -Vs1.
For the amplifier as shown, VDD = 12 V, VSS = 12 V, ISS = 20 μA, and RD = 820 kΩ. Assume IDSS = 1 mA and VP = +2 V. (a) What are the output voltages υo for the amplifier for υ1 = 0V and υ1 = 20 mV? (b) What is the maximum permissible value of υs?
Consider the amplifier in the figure given below, where VA = 50 V, VCC = 20 V, VEE = 20 V, IEE = 350 μA, βF = 120, REE = 320 kΩ, and RC = 72 kΩ. What are the differential-mode input and output resistances of the given amplifier?
(a)Find the Q-points of the transistors in the CMOS op amp shown if VDD = VSS = 5 V, IREF = 250 μA, K'n = 50 μA/V2, VTN = 0.75 V,K'p = 20 μA/V2, and VTP =− 0.75 V. (b) What is the voltage gain of the op amp assuming the output stage has unity gain and λ = 0.017 V−1 for both transistor types? (c) What is the voltage gain if IREF is changed to 500 μA?(d) What is the offset voltage of the ampliﬁer?
(a) What are the Q-points for the transistors in the amplifier as shown if VCC = 15 V, VEE = 15 V, IEE = 400 μA, βF = 100, REE = 270 kΩ,RC =47 kΩ, VA=∞, and βF =100? (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-modeinput and output resistances? (c) Repeat part (b) for VA = 50 V.
True or False Increasing RE improves the CMRR for single-ended output by increasing the differential-mode gain anddecreasing the common-mode gain. Increasing RE reduces the transistor DC currents and increases the DC output voltages. The double-ended output of the differential amplifier is always zero if vs1=vs2 for any value of RE.