form flow of water in a wide channel with a velocity of 8 m/s and flow depth of 0.8 m. Water flows over a 30-cm-high bump. Determine the change in the water surface level over the bump and flow over the bump is subcritical or supercritical. Your answer should include the following: B 2.1 Assumptions to be made to determine changes in the water su

form flow of water in a wide channel with a velocity of 8 m/s and flow depth of 0.8 m. Water flows over a 30-cm-high bump. Determine the change in the water surface level over the bump and flow over the bump is subcritical or supercritical. Your answer should include the following: B 2.1 Assumptions to be made to determine changes in the water su

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

A rectangular river channel 4.6 m wide carries water at a depth of 0.6 m. The slope of the channel is 1 in 400. As the channel has poor alignment and the bed is covered with stones about 75 mm to 150 mm in size, n is estimated to be between 0.04 and 0.08. Estimate the minimum and maximum discharge. What is the percentage difference in flow discharge?
High velocity water flows up an inclined plane, as shown in Figure 5 .1 What are the two possible depth of flow at section 2? Neglect al losses.
depth of water = 10 cm velocity of water = 6 meters/sec *The water flows in a rectangular-shaped channel* Given the conditions: 1. Is the water flow considered supercritical or subcritical? 2. Determine the alternate depth.
In the case of a rectangular channel 3 m wide and 1 m deep, the value of Manning's constant is 0.022 for earthen channel after weathering. For a bed slope of 1/2500, find the flow rate in m^3/s CHOICES: *1.94 *3.88 *2.37 *2.85 Please answer with complete and detailed solutions. Thank you. ASAP
Water flows in a rectangular open channel with a depth of y = 0.45 m and velocity of V = 1.45 m/s. What is the water level after a gradual step rise? Can you please explain it with steps and proof? a) The water level will rise b) The water level will drop.
The flowrate per unit width (q = Q/b) in a wide rectangular channel is q = 4 m2/s. Is the flow subcritical or supercritical if the depth is: (a) 0.8 m, (b) 3.2 m? Show all calculations.
A trapezoidal channel with a base width of 20 ft and side slopes of 2H:1V (2 horizontal to 1 vertical) carries a flow of 2000 cubic feet per second at a depth of 8.0 ft. There is a smooth transition to a rectangular channel 20 ft wide accompanied by a gradual lowering of the channel bed by 2.0 ft. Calculate the depth of the water within the rectangular channel in feet using a solver. Choose the most appropriate of the two solutions and support your answer.
A concrete dam and the flow net are shown in the Figure below. The following parameter are-5 3 given as: Nd=12, Nf=3.8, k=2.6X10 m/sec, and Ɣsat=19.5 kN/m .a) Calculate the total quantity of water lost by seepage in m3/day.b) What is the water quantity for each flow channel?c) What is the reading of pizometer if its location 1.5 m above datum?d) What is the factor of safety against piping at the down stream?
In a rectangular canal with energy height E= 3,5 m, the floor width is given as B= 5,6 m. Neglecting the effects of friction; a) Find the critical depth. b) Calculate the maximum flow that can pass at the given energy level. c) calculate the flow that can pass at a depth of h=2,3 m d) Determine at what depths and regimes the flow of Q= 27 m^3/sec flows. e) Draw the Koch parabola using the data you have obtained.
Water flows in a long, 2.50 m wide rectangular channel at a uniform flow depth of 1.07 m and a uniform velocity of 1.68 m/s. The hump height is 0.75 m. a. Calculate the flow depths immediately before, on top of, and immediately after a smooth hump on the channel bed. b. Calculate the force exerted by the flow on the hump.
Fluid Mechanics question: Water flow from a pone through a 10cm diameter pipe. Find the flow rate and velocity at the outlet B. Draw the Hydraulic Grade Line and the Eneregy Grade Line for the flow from A to B.
A channel having a cross-section shown below has a flow rate of 0.053 m^3/s. Compute the hydraulic radius if f=0.037 Answer in THREE(3) decimal places.