From the given figure Solve the following; Let P = 20 P kip/ft ↓↓↓ link B pin 2P kip ft 3₁3 3₁4²

Q: Describe something on the slide or figure that you understand, then create a question to ask a…

A: The image shows the graph drawn between the body's mass to the minimal weight and the specific cost…

Q: Example: A beam supports a load varying uniformly from an intensity of w lb/ft at the left end to p…

A:

Q: A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is - 17…

A: Given, A two member truss, AB=1m P= 10kN

Q: Create a graph that shows the acceleration due to gravity as a function of distance from the earth’s…

A: The acceleration due to gravity can be expressed as a function of distance from the earth’s surface.

Q: A simply supported beam is loaded as shown in the figure. Find the horizontal and vertical reaction…

A: From the figure, it is clear that support A is hinged and B is roller.Therefore,There will be two…

Q: 8- Determine maximum deflection. L 45 √2P → X

A: we will be able to get the equation of the elastic curve. where x and y are the coordinates shown in…

Q: A pan of negligible mass is attached to two springs of normal lengths as 0.5m each and having…

A: Given: K1=250 NmK2=500 Nminitial length of spring =0.5 m   We need to calculate the maximum vertical…

Q: Question 4 Critically evaluate the degree to which soil water washing is an effective method for…

A:

Q: Compute the following: a. wall shear b. wall moment c. Deflection at mid-span d. the maximum…

A: As per the guidelines we are supposed to answer only three subparts,. Kindly repost for other…

Q: In a consolidated undrained test with pore pressure measurement on a normally consolidated clay, a…

A: Given- σ3=200 kPa,axial stress σd=150 kPa,pore pressure u=75 kPa, It is needed to find the shear…

Q: Make an introduction about Fluid Displacement Method for Measuring Volume Solids. Cite your…

A: To find the volume of an object or solid we can use the fluid displacement method.

Q: Determine the bulk modulus of elasticity (in N/m2) of a liquid that decreases in volume by 3% due to…

A:

Q: Compute/Derived the following: a. wall shear b. wall moment c. Reaction

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: 19. The distance between Sta. 32+ 45.2 and Sta. 40 + 60.5 of a survey is A. 7305.7 ft. B. 905.7 ft.…

A: Given Data Two stations are given in the question. Station 1 = 32+45.2 Station 2 = 40+60.5 We are…

Q: 1. Four forces are applied to point P as shown. Knowing that F₁ = 50 lb, F2 = 20 lb and F4 = 70 lb,…

A:

Q: We presented Newton’s Law of Gravitation. We also explained the acceleration due to gravity. Create…

A: The acceleration due to gravity , g can be represented as a function of distance from Earth's…

Q: A 10 m cantilever beam has a uniform load of 2.5 KN/m from left to right end. Find the maximum…

A: we will be able to get the equation of the elastic curve. where x and y are the coordinates shown in…

Q: A solid circular torsional member OPQ is subjected to torsional moments as shown in the figure (not…

A: For region PQ,Torque, T=1 kN.mDiameter, D=0.08 mRadius, r=0.04 mPolar moment of inertia, J=πD432…

Q: 27. An open tank contains 5.7 m of water covered with 2.8 m of kerosene (y = 8.0 kN/m³). Find the…

A: Given:Height of water in the tank=5.7 mHeight of kerosene in the tank=2.8 mspecific weight of…

Q: Problem- Calculate the water distribution efficiency, if the depths of penetration along the length…

A: Given data- Depth of penetration = 1.5 m, 1.8 m, & 2.1 m. Border strip intervalal = 20 m. To…

Q: A 2 m diameter cylinder rotates at 1800 rpm in an air stream (p=1226 kg/m³) of 25 m/sec. Estimate…

A:

Q: E Listen Profile Level Notes: The elevation of BM A = 522.17' BS (plus sight) on BM A = 9.25' IFS…

A: Required :- elevation of the STA 0+00?

Q: Given a square kilometer of land, how many cars can be parked safely there? Determine the…

A:

Q: A straight cylindrical bar is 15 mm diameter and 12 m long. It is simply supported at its two ends…

A: Given, Diameter of bar= 15mm Length=L= 12m W=90N Central deflection, yc = 5mm Buckling load=?…

Q: Example: Determine the resultant of the forces shown. 80lb tat 3' + 50%b 3' 60%b +21 90%b

A:

Q: B- What the deference between particle imaging velocimetry and laser doppler velocimetry with…

A:

Q: Please draw the shear force diagram and bending moment diagram.

A:

Q: 1. a) What is the maximum moment? b) What is the maximum shear?

A: Let,W=Uniformly distributed load on the beamL=Length of the spanSince,Left support is a hinge…

Q: Rigid bar ABC is supported by bronze rod (1) and stainless steel rod (2) as shown in the figure. A…

A:

Q: answer c

A: a=15min b=0.005min/veh-hr c=6000veh/hr d=150veh/hr/min

Q: A smooth flat plate is in a parallel flow stream. The ratio of the drag over the upstream half of…

A:

Q: A Class II two-lane highway needs to be redesigned for an area with rolling terrain. During the peak…

A:

Q: thank

A:

Q: Given: A-in-thick. ASTM A36 eyebar member as shown in Figure D.8, carries a dead load of 25 kips and…

A:

Q: A tracer takes 100 days to travel from Well-1 to Well-2 which are 100 m apart. The elevation of…

A: Given- time t=100 days, distance s=100 m, elevation h=3 m, porosity n=15%=0.15,   It is needed to…

Q: What if any materials options do we have for graphene coating in construction? Do these options…

A: This type of coating is used to enhance the property of the steel. Thus the strength of the steel…

Q: express each Fahrenheit scale temperatureas a Rankine scale temperature. 5°F

A: GIVEN :-  5° Fahrenheit   TO DETERMINE :- Express the given Fahrenheit scale temperature as a…

Q: For the beam shown, determine the following: a. Maximum Positive Shear b. Maximum Negative Moment c.…

A: Given data:

Q: Situation 2: Determine the x and y coordinates and the resultant of the block with the forces acting…

A: GIVEN: TO FIND:  x and y coordinates and the resultant of the block with the forces acting upon it.

Q: If dry density, water density and specific gravity of solids of a given soil sample are 1.6 g/cc,…

A: Given data, For soil sample,  Specific gravity = G=2.56 Yw= 1g/cc Dry density = Yd= 1.6g/cc Find out…

Q: SOLVE FOR THE MOMENT OF JOINT , TABULAR AND STATE WHETHER TENSILE OR COMPRESSION

A:

Q: convert 259 lb/ft2 to kg/in2

A: lb/ft2 is basically units of pressure. Pressure is nothing but a physical force imposed on an…

Q: the minimum length of the chamber (in m, in integer)

A: Given, Determine the minimum length of the chamber to remove 0.25 mm particles ?Diameter,d= 0.25 mm…

Q: 1. Two structural members B and C are bolted to bracket A. Knowing that both members are in tension…

A: GIVEN : Two structural members having tension of magnitude P & Q respectively. P = 10 kN Q = 15…

Q: PROBLEM: Prove that the truss shown is statically determinate and solve for the force members. State…

A: Truss, no.of members = 21 no.of joints = 12 Length of the truss = 3+3+3+2+2+2 = 15m Height of truss…

Q: A 0.3 saturated soil has specific gravity of 2.1 and moisture content 0.44. Find void ratio of soil

A:

Q: Water flows at a rate of 12 m/s through an almost level channel 3 m wide. The depth gradually…

A: Given:- flow rate=12m3/secwidth of level channel=3mdepth increases =1m to 1.1mlength of flow=5mTo…

Q: METHOD OF JONTS 20K 30k B 12 с Tok ICY 5 20 50k E 10' wk 118 G 10 40k 1 Tok I 10' 30k 20k к sok befo…

A:

Q: P= 356 kN P= 178 KN A D G 6 m B E H 7 m C 6 m

A: Solve the frame using portal frame method: Shear force in column: Top Storey: ∑fx=0 P+2P+P=356…

Q: 1.10 Describe the steps a land surveyor would need to do when performing a boundary survey.

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.