24. From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a transformer can be obtained (itis then referred to the low voltage end). The transformer is rated 50 kVA,60 Hz, 2300:230 V. If it is delivering power at ratedload, 0.85 lagging pf, determine:a. Load current, In.b. Iмc. Icd. What is the value of Vp?0.0084633 Nj0.0246696 nVp153.3333 0Elc IMj197.2234050 kVA23020° V Z100.85 pf lag

Answered: Image /qna-images/answer/31bcc373-2871-490b-b74a-ebf271253fcf.jpg

From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a transformer can be obtained (it is then referred to the low voltage end). The transformer is rated 50 kVÄ,60 Hz, 2300:230 V. If it is delivering power at rated load, 0.85 lagging pf, determine: a. Load current, IL b. IM c. Ic d. What is the value of Vp?

From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a transformer can be obtained (it is then referred to the low voltage end). The transformer is rated 50 kVÄ,60 Hz, 2300:230 V. If it is delivering power at rated load, 0.85 lagging pf, determine: a. Load current, IL b. IM c. Ic d. What is the value of Vp?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.29MCQ: For developing per-unit equivalent circuits of single-phase three-winding transformer, a common...

See similar textbooks

Similar questions

Consider a source of voltage v(t)=102sin(2t)V, with an internal resistance of 1800. A transformer that can be considered as ideal is used to couple a 50 resistive load to the source. (a) Determine the transformer primary-to-secondary turns ratio required to ensure maxi mum power transfer by matching the load and source resistances. (b) Find the average power delivered to the load, assenting maximum power transfer.
A single-phase 50-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer at the load end of a 2400-volt feeder whose series impedance is (1.0+j2.0) ohm. The equivalent series impedance of the transformer is (1.0+j2.5) ohms referred to the high-voltage (primary) side. The transformer is delivering rated load at a 0.8 power factor lagging and at a rated secondary voltage. Neglecting the transformer exciting current, determine (a) the voltage at the transformer primary terminals, (b) the voltage at the sending end of the feeder, and (c) the real and reactive power delivered to the sending end of the feeder.
A three-phase transformer is rated 1000MVA,220Y/22kV. The Y-equivalent short-circuit impedance, considered equal to the leakage reactance, measured on the low-voltage side is 0.1. Compute the per-unit reactance of the transformer. In a system in which the base on the high-voltage side of the transformer is 100MVA,230kV what value of the per-unit reactance should be used to represent this transformer?
An ideal transformer with N1=1000andN2=250 is connected with an impedance Z22 across winding 2. If V1=10000VandI1=530 A, determine V2,I2,Z2, and the impedance Z2, which is the value of Z2 referred to the primary side of the transformer.
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
For developing per-unit equivalent circuits of single-phase three-winding transformer, a common Sbase is selected for all three windings and voltage bases are selected in proportion to the rated voltage of the windings (a) True (b) False
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) False