FUNDAMENTAL PROBLEMS V27 Resolve cach force acting on the post into its I and y components. F2-10. If the resultant force acting on the bracket i lo be 750 N directed along the positive x axis, determine the magnitude of Fand its direction . 300 N -450 N 325 N 5-600N Prob. F2-7 F28. Determine the magnitude and direction of the resultant force. 20N Prub. F2-10 FLIL. If the magnitude of the resultant force acting on the bracket is to be 80 lb directed along the uaxis, determine the magnitude of F and its direction . 40 N 300N 90 Ib Prob. F28 Prob. F2-11 F29. Determine the magnitude of the resultant force acting on the corbel and its direction measured counterclock wise from the x axis F212 Determine the magnitude of the resultant force and its direction o measured counterclockwise from the positive x axis 400 b - 70 h 20 kN Page

FUNDAMENTAL PROBLEMS V27 Resolve cach force acting on the post into its I and y components. F2-10. If the resultant force acting on the bracket i lo be 750 N directed along the positive x axis, determine the magnitude of Fand its direction . 300 N -450 N 325 N 5-600N Prob. F2-7 F28. Determine the magnitude and direction of the resultant force. 20N Prub. F2-10 FLIL. If the magnitude of the resultant force acting on the bracket is to be 80 lb directed along the uaxis, determine the magnitude of F and its direction . 40 N 300N 90 Ib Prob. F28 Prob. F2-11 F29. Determine the magnitude of the resultant force acting on the corbel and its direction measured counterclock wise from the x axis F212 Determine the magnitude of the resultant force and its direction o measured counterclockwise from the positive x axis 400 b - 70 h 20 kN Page

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
2. A 50- m steel tape weighs 0.04 kg/m and is supported at its end points andat the 9-m and 30- m marks. If a pull of 6kg is applied, determine thefollowing:a) correction due to sag between the 0-m and 9- m marks, 9-m and 30-mmarks, and the 30- m and 50- m marks.b) correction due to sag for one tape lengthc) correct distance between the ends of the tape.
A column section b = 400 mm, h = 600 mm is reinforced with longitudinal bars Ast = 8-ϕ25 mm equally distributed along all faces. Lateral ties are composed of 12 mm rectangular hoops with clear cover equal to 40 mm and 12 mm cross ties in both directions. Concrete yield strength f’c = 27 MPa and steel yield strength, fy = 415 MPa.Calculate the nominal axial strength of the column in kN.A. 7 047 B. 5 638C. 4 580 D. 6 342 Calculate the center to center spacing of ties for confinement.A. 200 B. 400C. 500 D. 300 Where is the plastic centroid measured from the short edge of the column?A. 200 B. 400C. 500 D. 300 Calculate the steel stress (MPa) in the middle layer of bars at balanced strain condition.A. 31.37 comp B. 43.52 compC. 31.37 tension D. 43.52 tension Calculate the nominal axial strength in kN of the column at balanced strain condition considering bending about the strong axis.A. 3,420 B. 2,500C. 2,875 D. 3,846
The steel truss supports a 6000-lb load. The cross-sectional areas of themembers are 0.5 in.2forABand 0.75 in.2forBC. Compute the horizontal displace-ment ofBusingE¼29106psi. ans. no. 10 only , GIVEN, REQD AND COMPLETE SOLUTION
Three forces act on the bracket. Determine themagnitude and direction θ of F so that the resultant force isdirected along the positive x' axis and has a magnitudeof 8 kN.
The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is displaced 0.75 in. downward when P isapplied. a.) Determine the elongation of the guy wire in inches when load P is applied.b.) What is the required diameter of the guy wire in inches to support the load P = 42 kips?
Problem 14 , 3 parts ....plz solve all parts I vll upvote
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
Compute the internal force of member CD & EF
For the frame loaded as shown, draw the complete and correct FBDs of thefollowing: whole frame, member BE, member HK, pulley D, pulley J, member CDEHJwithout the pulleys, and pin B. If block G weighs 133 N, determine all the forcesacting on member CDEHJ (i.e. Cx, Cy, Dx, Dy, FBE, FHK, Jx and Jy). Also, calculate thehorizontal (ABCBx) and vertical (ABCBy) components of the reactions betweenmember ABC and pin B.
Specify the magnitude and coordinate directionangles a1, β1, γ1 of F1 so that the resultant of the threeforces acting on the bracket is FR = {-350k} lb. Note thatF3 lies in the x–y plane.
Instruction: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: Neglecting the weights of the members, determine the magnitude of the pin reaction at D when the frame is loaded by the 200-N.m couple.