Gate AB in Fig. (4) is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric-pressure effects, compute the force F on the gate and its center of pressure position X. -6 m- 4 m Oil, SG = 0.82 8 m m 2.ו 40° Fig. 4

Gate AB in Fig. (4) is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric-pressure effects, compute the force F on the gate and its center of pressure position X. -6 m- 4 m Oil, SG = 0.82 8 m m 2.ו 40° Fig. 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the resultant force F due to water acting on the 3 m by 6 m rectangular area AB shown in…

A: given data area of gate =3m×6m take γ=9.81 KN/m3 for water we know that pressure = ρgh force =…

Q: A closed cylindrical vessel, axis vertical 4m high and Im in diameter is just filled with water. At…

Q: Plot the distribution of active pressure on the wall surface shown in Figure 6.37. Calculate the…

Q: A square frame 5 m by 5 m in dimension is submerged in water vertically with its top of 3 meters…

Q: An isosceles triangular gate with a horizontal base 3 m long and vertex pointing downward is…

A: Using formula

Q: H.W1: Determine the pressure difference between points A and B in Fig below?

A: γ=ρg=ρ×9.81γbenzene=880x9.81 =8632.8 N/m3γmercury=13600x 9.81 =133416 N/m3γkerosene=850x9.81 =8338.5…

Q: An inclined rectangular gate with water in one side is shown in fig. (2.2). find the total resultant…

A: The center of pressure is the point where the total sum of a pressure field acts on a body, causing…

Q: Gate AB in Fig. (4) is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric-pressure effects,…

A: answer = hydrostatic force 38.750 KN value of x = 61.5 cm

Q: Q3:Find the resultant force direction and position of (c.p.) of the hydrostatic force on the…

Q: Each gate of a lock is 5m high and is supported by two hinges placed on the top and bottom of the…

Q: F={26i?49j+55k}lb. 3 ft 4 ft B 4 ft 2 ft Determine the magnitude of the component of F acting along…

A: Given values: F = (26i - 49j + 55k) lb

Q: W.S.V

Q: What is the pressure at the center of pipe B? y 10 kN/m3 y = 20 kN/m3 50 cm 50 сm 10 cm

A: To find pressure at point B

Q: A 5m long, 2m wide and 2m high tank is filled with water. a. Solve the resultant hydrostatic force…

Q: Q1: The U tube (in Fig.1) is open at (D) and closed in (A). What will be the pressure at point (A, B…

Q: 3. A closed cylindrical tank 2m in diameter and 9m deep with axis vertical contains 7m deep of oil…

Q: Q1: In Figure below find the resultant pressure force and the depth of the centre of pressure on the…

Q: 3. A closed cylindrical tank 2 m diameter and 4 deep contains 3m depth of water. Air at a pressure…

Q: Gate AB in Fig. P2.56 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric pressure,…

A: Given: The length of the gate AB is 1.2 m. The thickness of the gate AB is 0.8 m. Consider the…

Q: a) See instructions. The pressure (gauge) at the gate's centre (in Pa) is O a. 59600 o b. 40000 OC.…

A: Given :- One vertical side-wall has a square gate of side-length D The gate's centre is at a depth q…

Q: 2.51 Gate AB in Fig. P2.51 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric-pressure…

Q: A vertical rectangular gate 1.8 m wide and 4.2 m high is submerged in oil (SG=0.88) with its top…

Q: When the water at tide A descends, the tide gate automatically rotates by opening to drain the water…

A: FBD of Gate : Maximum intensity of pressure on left side of gate, w1 = 3ρg = 3×1.0×103×9.81 = 29430…

Q: An oil having viscosity 0.08 N-s/m², specific weight 8829 N/m³, density 900 kg/m³ flows at the rate…

A: Given- viscosity μ=0.08 N-s/m2Specific weight γ=8829 N/m3density ρ=900 kg/m3discharge Q=5.4×10-3…

Q: Item 4a. Derive an equation for finding the location of the center of pressure of a vertically…

Q: An inclined, rectangular gate with water on one side is shown in Fig. 3-9. Determine the total…

A: To find total resultant force and location of center of pressure

Q: 3. An inclined circular gate 0.6 m in diameter with water in one side is shown in fig. (2.3). find…

A: Consider the given data.

Q: This is an open cylindrical vessel* It is filled 2/3. diameter = 0.60 m height = 0.90 m 90 rpm a.…

Q: Q2. A circular plate 1.2 m in diameter is submerged in water, with its greatest and least depths…

Q: Q2:Calculate the value and direction and position of effect of hydrostatic force affected on the…

A: Given that .....

Q: What is the pressure at the bottom of the disk? Unit weight of water is 9.79 kN/m³. W.S. 3m 0.6- Im

A: We have to determine the value of pressure at the bottom of the disk according to the given data.

Q: Consider the retaming wall shown in the Figure below Calculate the Rankine passive force per unit…

A: As per company's guidelines we can only answer first question. Kindly post other questions as…

Q: An inclined rectangular sluice gate AB 1.2 m by 5 m size as shown in Fig. 2 is installed to control…

Q: If a triangular gate of height 694 mm and base of 566 mm is vertical and submerged in c with its…

A: Height of triangular section = 694mm Base of Triangular section = 566mm Oil density = 800kg/m3…

Q: The open circular RCC water tank of diameter 5 m resting on firm ground with flexible base for 350…

A: Given data Diameter of tank (D) = 5m Height of wall (H) = 4m Unit weight of water (Yw) = 10 KN/m3

Q: h (m) Determine the magnitude of the hydrostatic force acting per meter length of the wall. Unit…

Q: Q1/ Prove that pressure does not vary in horizontal direction ( OP -0), and the pressure dx aP…

A: Context: Pressure variation in the horizontal and vertical direction

Q: Water flows over a flat plate at a free stream velocity of 0.20 m/s. There is no pressure gradient…

Q: Determine the difference in pressure (kPa) between A and B. a= 4.06 meters b= 2.96 meters

Q: 02 A smooth backed wall is 6m height and retain a soil with the properties shown in the Figure…

Q: open tank 1.8 m. by 1.8 m. and 1.3 m. deep contains water at a depth of 0.90 m. The weight of the…

A: Given:- Tank size=1.8 X 1.8 X 1.3 m Water depth = 0.90m weight of tank = 3500N Unbalanced…

Q: A circular plate 2m in diameter is submerged in water with its higher and lower edges located at 2m…

A: Given :

Q: Q.2 (e) The effective lateral active pressure KN/m2 at :point (C) is

A: COFFICIENT OF ACTIVE EARTH PRESSURE: Ka=1-sin ϕ1+sinϕ In active state wall moves away from backfill…

Q: An open rectangular tank 2.2m in length contains 16m^3 of gasoling (sg=0.70) and 23m^3 of water. The…

Q: - For the retaining wall shown in the figure below, assume that the wall cen yield sufficiently to…

A: step 1-

Q: A 3 m high, 6 m wide rectangular gate is hinged at the top edge at A an is restrained by a fixed…

Q: A gate in a shape of rectangle with base of 1.5m and height of 3m is inclined in a slope 1:2 and…

A: To determine Hydrostatic pressure, depth of hydrostatic pressure, reaction at hinge and wall.

Q: A vertical, trapezoidal gate in the face of a dike is subjected to sea water pressure (s = 1.3) on…

Concept explainers

Thermal Processes

Some of the key areas where thermal processes find their application are:

Question

Choose the correct answer

a-0.615 N, 38750 m

b-38705 N, 0.651 m

c-38.750 KN, 61.5 cm

d-None of theses

e-38750 kN, 0.615 mm

Gate AB in Fig. (4) is 1.2 m long and 0.8 m into the paper. Neglecting atmospherie-pressure
effects, compute the force F on the gate and its center of pressure position X.
-6 m-
4 m
Oil.
SG = 0.82
8 m
1.2 m
40°
Fig. 4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Application of Equilibrium Solve for the value of unknown variables Given : P1 = 10KN W1 = 5 KN/m P2 = 6 KN W2 = 10 KN/m θ= 58° a.Unknowns: RAy , RBy , RBx , MB b. compute the internal shear 1.35 m to the right of support A
The weight of the gate is 50 kN acting 1.2 m to the right of O. Determine the Hydrostatic Force.
Determine sum of vertical support reaction at A and B
the inclined circular (D = 4.06 m) gate shown below retains a liquid with Sg = 3.35 on one side. the vertical distance from the liquid surface to the top of the gate, h, is 2.42 m. use 39 degrees. determine the hydrostatic force (kN0 acting on the gate.
A tank used to collect rainwater having diameter of 4m .the depth of the tank varies linearly from 3.5m at its center to 3m along the perimeter.the local atmospheric pressure is 1bar ,the acceleration of gravity is 9.8mS square and the density of the rainwater is 987.1kg/m3. When the tank is filled with water,determine a) the pressure in kPa at the bottom center of the tank b)the total force in kN,acting on the bottom of the tank
A 6 m. cantilever retaining wall, supports an active pressure which varies from zero at the top to 35 kN/m at the bottom. Assume EI is constant. 1. Compute the maximum moment. 2. If the wall is fixed at the free end, determine the moment at the foundation. Use end moment equations wL^2/30 at the top and wL^2/20 at the base.
The retaining wall shown has a height of 6m with its ground watertable located at a depth of 2m below the ground surface. There is a surcharge of 15kN/m^2 at the top. Compute the Rankine active force on the wall per unit. Compute the location of this force from the bottom of the wall. Compute the moment due to this force.
For the maximum water height at full supply level, calculate the complete vectorof the resultant force on the central section of the dam wall per metre length,as it would pass through the dam base, with respect to the downstream toe (D).Account for the hydrostatic thrust force on the upstream (A-B) and downstream(C-D) faces of the dam, pore pressure on the base (A-D) and the weight of thedam wall.The weight of the radial gate and gate supporting structure can be ignored.Assume the radial gates are fully closed and there is no water on the spillway.
The cylinder weighs 10 lb and is held in equilibrium by the belt and wall. If slipping does not occur at the wall, determine the minimum vertical force P which must be applied to the belt for equilibrium. The coefficient of staticfriction between the belt and the cylinder is μs = 0.25.
Draw the lateral earth pressure distributions for both sides of the wall. Compute the Active Rankine Force.
Q1b) A vertical gate of height 5 m and width of 3 m opposes the water at one of its sides. The deep of the water in the reservoir is 20 m. Determine the pressure and the force acting at the centroid of the gate.
Isosceles triangle gate AB below is hinged at A and weighs 1500 N. What horizontal force magnitude P is required at point B for equilibrium? Take the specific weight of the water as γwater = 9810 N/m^3