Give a simple heuristic for finding two paths through a network from a given source to a given destination that can survive the loss of any communication line (assuming two such paths exist). The routers are considered reliable enough, so it is not necessary to worry about the possibility of router crashes.

Give a simple heuristic for finding two paths through a network from a given source to a given destination that can survive the loss of any communication line (assuming two such paths exist). The routers are considered reliable enough, so it is not necessary to worry about the possibility of router crashes.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter9: Computer Networks

Section: Chapter Questions

Problem 9VE

See similar textbooks

Similar questions

Write a program to simulate routing using ooding. Each packet should contain a counter that is decremented on each hop. When the counter gets to zero, the packet is discarded. Time is discrete, with each line handling one packet per time interval. Make three versions of this program: all lines are flooded, all lines except the input line are flooded, and only the (statically chosen) best k lines are flooded. Compare flooding with deterministic routing (k=1) in terms of both delay and the bandwidth used.
Let's pretend that we're on a fixed path, and we're trying to send a packet to a host. from a starting point to a finishing point List the many components of delay as well: Approximately how many delays are continuous for how long, and approximately how many are timedependent?
It is necessary to do research on connectionless protocols in order to determine whether or not they can successfully replace connection-based protocols.
Let's get started by taking a more in-depth look into routing. Determine the key differences between these two widely used routing approaches.
Assume a simple network of two directly adjacent routers. At time T=0 seconds both sent updates (A -> B "can reach 10.0.0.0 with cost 1", B -> A "can reach 20.0.0.0 with cost 1"). At time T=10 second router B exploded and, as a sad consequence, it stopped sending or receiving any packets. Select all statements that are true: - If at T=15s A sends a packet to 20.0.0.1, A will immediately drop the packet - If at T=15s A sends a packet to 20.0.0.1, it will not reach the destination - If at T=125s A sends a packet to 20.0.0.1, A will immediately drop the packet - At time T=125s node A has no knowledge about the route to 20.0.0.0/24 - If at T=185s A sends a packet to 20.0.0.1, A will immediately drop the packet - At time T=185s node A has no knowledge about the route to 20.0.0.0/24 - If at T=305s A sends a packet to 20.0.0.1, A will immediately drop the packet - At time T=305s node A has no knowledge about the route to 20.0.0.0/24
Do you have to use a certain EIGRP parameter when distributing a route? The exit interface and the IP address of the following hop are only two examples of the many variables that may have an impact on administrative distance.
Assume for the sake of this example that a packet is being sent from a source to an address at the other end of the network via the fixed route. List all the delays' varied causes as well: How many delays are roughly time-dependent and how many are roughly continuous for how long?
In an RPC-like protocol, where numerous requests can be active at the same time and responses can be given in any sequence, the following is possible: Pretend requests are sequentially numbered, and that ACK[N] confirms the receipt of reply[N]. Should the number of ACKs be cumulative? If not, what should happen in the event that an ACK is not received?
What exactly is it that the routing protocol is trying to accomplish? You may get a better idea of how the Routing Information Protocol, sometimes known as RIP, works by looking at the following working example.
Give a brief review of the pros and cons of using connectionless protocols instead of connection-based ones.
In this example, assume that the fixed path is used to transport a packet from a source to an address at the other end of the network. List the many components of delay as well: Approximately how many delays are continuous for how long, and approximately how many are timedependent?
One problem with DistanceVector routing is the "Count to infinity" problem. What does this mean?Group of answer options In the event of changes in the network, it takes a long time before the routing tables become correct The routing tables can be infinitely large The number of necessary routers can be infinitely large It will be very time consuming to configure the routers correctly