give illustration or drawing of a model of strong bridge that will use bbq stick and bands.

Q: Using Dim, solve for the following 40kN/m 10kN/m в A 30 kN-m 7.0 m 3.0 m 4.0 m a. Maximum Deflection…

A:

Q: Draw the shear and moment diagram of the given beam.

A:

Q: As a project manager, how are you going to ensure that the goal of the project is being followed?…

A: As a project manager we have to keep in mind certain points for the completion of our project goal.

Q: 4. Estimate the production in compacted cubic yards per hour of a tamping foot, wheel-tractor-towed,…

A: This question is related to the Geotechnical Engineering.

Q: Latitude and Departure Given the observed data of a closed traverse, determine the latitudes and…

A: Length and bearing have been given and it has been asked to determine latitude and departure. Please…

Q: Given: Beam with loading and supports shown Maximum allowable stress in the steel bar is 30 ksi…

A: Given data - Steel Properties -  E = 29000 ksi (kips/in2) G = 11200 ksiCoefficient of thermal…

Q: 6. Determine the slope at point C of the frame shown in the figure. The support A is fixed. Take E-…

A: To find slope at C

Q: 2 kulm 8KN 4m

A:

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

A:

Q: Given the follbwing composhe fig ure, solve the tollowing ) location of the contoi d of the…

A:

Q: If our bullding is functioned as school and the external waste line pipes are planned to use for…

A: PPRC pipes are preferred.

Q: 50KN 50KN A B 5m 5m 5m 5m

A:

Q: 23. A hemispherical tank having a radius of 2.5 m is filled with water to a depth of 1.8 m. If a…

A: As per rule , I had done only civil engineering questions, ie. 21 and 23 solution . 21

Q: %3D Imin in4 %3D Imax in4

A: Mohr’s Circle: - It is a two dimensional graph by which one can see the variation of normal and…

Q: Given data : Stress=30 N/mm2 Force=2 N Find cross sectional area

A:

Q: PROBLEM 05. A stepped shaft has the appearance shown in fig. The region AB is Al2014-T6 alloy,…

A:

Q: weight of a man

A: This question has been taken from fluid mechanics:

Q: Consider a square-shaped area ABCD on the ground with tis centre at M as shown in the figure. Four…

A:

Q: - 50mm clear 5-025mm 300mm clear 375mm Given the data below, Is the design sufficient for the 900…

A: Answer We are given Epoxy coated reinforcement Side and top cover is 65 mm on bar extension  Column…

Q: Design a 300 mm x 500mm rectangular beam to carry a dead load moment of 80 kN-m (including its own…

A:

Q: 1. The performance data of a water pump follow the curve fit Havailable =Ho +aV?, where the pump's…

A:

Q: Using Dim, solve for the following

A:

Q: Determine the x and y components of the force system and the magnitude of the resultant and the…

A: ###Determination of component of forces and resultant and direction ####

Q: force, Pa, per unit length of the wall and the location of the resultant. kN 15.5 kN IfH %3D 6т, Н,…

A: Height of wall = 6m  Step 1  Surchage remain constant all over the section Step 2  Water apply water…

Q: Calculate the total area (m2) of a cross section using Simpson's 1/3 Rule. Consider the following…

A:

Q: Determine the LRFD design strength and the ASD allowable strength of the W16x31 shown including the…

A: Given  W16×31  and Grade of steel = A992 for A992 steel,   yield stress Fy = 50 ksi, ultimate stress…

Q: Laplace equation for water flow in soils is given

A:

Q: Solve support reactions. note: there is an internal hinge at C

A: ##Calculation of Support reaction ###

Q: the volume of the metal in cubic meters.

A: This question has been taken from the concept of buoyancy in Fluid mechanics. The answer is 15.80cc…

Q: Determine the reaction at B. 500 N 800 N-m 5 m -4 m 8 m

A:

Q: In relation to the "primary structure" or "released structure" in the flexibility (force) method:…

A: (d) option is correct   After the structure is released from the redundancy the resulting structure…

Q: 66KN 5@2 m = 10 m

A:

Q: For the cross-section of the angle shown below, use Mohr's Circle to determine the orlentation of…

A:

Q: Solve all support reactions in the given beam using double integration method. Also, determine the…

A:

Q: vertical road was designed with three tangent lines having a grade of -7.8%, 3.7%, and -2.1%,…

A: Elev of A = 216.4m

Q: Given data : Stress=30 N/mm2 Force=2 N Find cross sectional area

A:

Q: Two highway centerline tangents must be joined with a circular curve of radius 300 m. The point of…

A:

Q: Design the reinforcement for the following short braced column: Breadth, b = 400 mm Depth, h = 400…

A:

Q: Determine the safe service load W permitted for this beam-column that is not part of a frame system.…

A: For A992 steel fy = 50ksi

Q: Calculate the elastic settlement under the center of the flexible foundation shown in the figure…

A: Data given γsoil= 120 lb/ft3 B = 6 ft Df = 3 ft time = 1 year △σ = q¯ = 25000 lb/ft2 Solution…

Q: Draw the shear and moment diagram and determine the Vmax and Mmax of the simple beam shown below, Wo…

A: A loaded beam is given and it has been asked to draw shear force and bending moment. Please refer…

Q: At the instant shown, the tower crane rotates about the z axis with an angular velocity wi = 0.18…

A:

Q: 1.9 kN 0.9 kN 1.2 kN/m 0.75 kN/m A B 0.9 m 1.5 m 6 m

A:

Q: A steel rod suspended vertically carries an axial tensile force of 30kN at one end and has a length…

A:

Q: From the given figure below. Determine the R1, R2, and the length of the compound curve.

A:

Q: Determine the following based on the figure: A. Y-Coordinate of the centroid B. Moments of inertia…

A: Note : I have solved 1st 3 part as per guidelines of bartleby

Q: etermine the reactions at A an

A:

Q: 3. Value of Young's modulus of elasticity if, Bulk modulus is 170 GPa and Poisson's ratio is 0.29…

A:

Q: A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig =…

A:

Q: The floor of an apartment building is subjected to a uniformly dintributed load of 45 psf over its…

A: