Given a discrete-time signal x[n] as shown in Figure Q1(c). (1) Sketch the signals x[2n], x[n+2], and x[-n+3]. (ii) Analyse and express the signal x[n] in terms of unit sample sequence 8[n]and its scaled and shifted version. (iii) Calculate the power of the signal x[n]. X[n] 3 3 2 3 -3 -2 1 2 -1 Figure Q1(c)

Given a discrete-time signal x[n] as shown in Figure Q1(c). (1) Sketch the signals x[2n], x[n+2], and x[-n+3]. (ii) Analyse and express the signal x[n] in terms of unit sample sequence 8[n]and its scaled and shifted version. (iii) Calculate the power of the signal x[n]. X[n] 3 3 2 3 -3 -2 1 2 -1 Figure Q1(c)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the voltage gain expression (?? = ????/???) of the circuit given below in terms of R1, R2, R3, and Rf.
Express the voltage, current, and power gains ,a signalvi = 0.1 sin 2000πt volts Thévenin equivalent source resistance RI of 2 kΩ, and we ’d like to listen to that signal with a 32-Ω ear bud, represented by the load RL , as depicted by the circuit model in dB.
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
A signal a[n] is applied to a system Z, to produce an output signal b[n] = 2a[n]. An output signal b[n] = a[n] - a[n-1]is produced when a signal a[n] is applied to a system Y. An output signal b[n] = 2a[n] + a[n-1] is applied to a system X. where X,Y,Z represent independent discrete systems. i. Suppose system Y is connected in series with system X, determine the resulting output relation of the interconnected system. ii. Suppose system Z is connected in parallel with system Y, determine the resulting output relation of the interconnected system.
Element values in the circuit given in the figure are given below. R1=55kΩ,R2=8.4kΩ, Rc=6.8kΩ, RE=2kΩ, Vcc= 22V, β=90, C1=C2= 10μF, CE=20μF a) Calculate the VB, VE,IE,re b) Draw the small sign equivalent circuit of the circuit. c) Using the small signal circuit, write the expression for the input resistance of the circuit and calculate it. d) Write the expression for the output resistance of the circuit using the small sign circuit and assuming the output resistance of the transistor to be infinite; Calculate numerically. e) When the output resistance of the transistor is assumed to be infinite, obtain the output voltage in terms of the input voltage and calculate the gain. *when you solve the first 3 steps, I will send it separately for the other three steps ***this part2 can you also solve d and e, please?
Element values in the circuit given in the figure are given below. R1=55kΩ,R2=8.4kΩ, Rc=6.8kΩ, RE=2kΩ, Vcc= 22V, β=90, C1=C2= 10μF, CE=20μF a) Calculate the VB, VE,IE,re b) Draw the small sign equivalent circuit of the circuit. c) Using the small signal circuit, write the expression for the input resistance of the circuit and calculate it. d) Write the expression for the output resistance of the circuit using the small sign circuit and assuming the output resistance of the transistor to be infinite; Calculate numerically. e) When the output resistance of the transistor is assumed to be infinite, obtain the output voltage in terms of the input voltage and calculate the gain. *when you solve the first 3 steps, I will send it separately for the other three steps
The voltage gain of an ampliﬁer is described by A(s)= 4π2 ×1018s2 / (s+200π)(s+2000π)(s+2π ×106)(s+2π ×107) (a) What are the mid-band gain and upper- and lower-cutoff frequencies of this ampliﬁer? (b) If this ampliﬁer is used in a feedback ampliﬁer with a closed-loop gain of 100 , what are the upper-and lower-cutoff frequencies of the closed-loop ampliﬁer? (c) Repeat for a closed-loop gain of 40.
Please find the following:(a) The error constants Kp, Kv and Ka and also the system type.(b) The range of K so that the steady-state error (i.e., e(t) = r(t) - c(t) as t -> ∞)under a unit ramp input is less than 0.01.(c) The range of K that keeps the system stable. (d) The value of K that makes the system oscillate and also the frequency ofoscillation. (e) Suppose that we replace the constant gain controller K with the moresophisticated PI controller, i.e., Gc(s) = K + (KI/s), find the range of thecontroller gains (K, KI) so the system is stable.
1. Consider the state space system with the given picture. Is this a valid state-space system? 2. (sperate problame0 Write down a transfer function of a stable system for which pure proportional feedback could drive the system unstable.
Design a radio receiver that powers an amplification system. The radio signal can be considered as an input voltage, while the amplification system, which is a two-terminal device, can be modeled as an equivalent resistance of 1 kΩ. A bandwidth of 500 kHz and a maximum power frequency of 10MHz are required.a) What is the quality factor?b) Do you consider that your receptor is selective or not very selective?
(a) What are the functions of capacitors C1, C2, and C3 as shown? (b) What is the magnitude of the signal voltage at the base of Q1?
In terms of linearity and time invariance of a system whose input-output relationship is given as Please examine.