Given are the length and direction of each course of a closed traverse: Line AB: 120 m; AZn = 164° 30’, Line BC: 115m; AZs = 210° 30’, Line CD: 75m; N 15° 30’

Q: a) A PFR has a conversion of A of 90% (i.e. C = 0.1C), and the reaction is first order. If a…

A: Given, Dispersion number = 1  % conversion = 90%

Q: A large stream has a reoxygenation constant of 0.4 per day. At a velocity of 0.85 m/s; and at the…

A:

Q: H.W2: 1- discuss the stability and determinacy of the following structure 2- Draw N, V and M…

A: Given: Required: Stability and determinacy N, V and M diagram

Q: If a rainstorm of 8 cm gives the runoff of 4 cm in a catchment whose -index is fixed and for whole…

A: Given: Total rainstrom or rainfall = 8 cm Total runoff = 4 cm Whole period of 3 hrs of rainfall.…

Q: 1. The loaded beam has a rectangular section with b = 1.5 in and h = 3.0 in. Loads M and w are 10…

A: Given:- M=10 lb-inW=4 lb/ina=12 inb=12 inc=24 inE=1.60×106 psi Cross section of the beam is…

Q: Analyze the given semi-frame and Develop the required equation/solution for every given answer. 1.…

A: Given: Required: shear and moment at the left of C  shear and moment at the right of C

Q: In writing the station, no space between the numbers and the plus (+) sign. Example: correct:…

A:

Q: Calculate the monthly average evaporation from the open water surface using the Penman method…

A:

Q: Q3/ Determine the equivalent passenger car unit for the following traffic composition if the total…

A: This question is from Traffic Engineering.

Q: A sample was obtained from point A in the submerged clay layer shown below. It was determined that…

A: A )  Given Data : w = 54 % Gs = 2.78  To Find : Effective vertical stress at A ? A problem of Soil…

Q: Find the reaction at supports R=37 (0.2+R) K 4' ET O 8 K RK ₁20 k

A: First we summarise the given data : R = 37 To Find : Determine the reaction at Supports.

Q: H.W2: Analysis the truss shown in fig. Or find all bars forces and supports reactions. 5 KN A F G B…

A:

Q: Solve the reactions using consistent deformation or superposition. Show complete solutions in 3…

A: Given: W = 134 Required: Support reaction

Q: Problem 32: Determine the maximum slope and maximum deflection for the given simply supported bearn…

A: Given :   This is a problem of Structure where we have to determine the max. slope and max.…

Q: From the given figure of a cable connection * shown. Which of the following gives the Tension (T3)…

A: Given Data  Find the tension force in each member.

Q: H.W4: 1- discuss the stability and determinacy of the following structure 2- Find the axial force in…

A: Given: To find: 1. The stability and determinacy of the given frame.

Q: A vertical 4.80-kN load is applied as shown on a wooden post of rectangular cross section, 80 by 120…

A: A )  Given data : Rectangular cross section = 80 mm X 120 mm Vertical load 4.80 k-N To Find : a )…

Q: Determine the magnitude and the position vector AC in ft.

A:

Q: Consider a 304.8mm section of a single-riveted lap joint made up with plates of 6.35mm thickness and…

A: The given data is as follows: Width of plate=304.8 mmThickness of each plate=6.35 mmNumber of…

Q: 8 The gate AB is 4.60 m long and 2.4 m wide perpendicular to the paper and is hinged at A with a…

A: To determine the weight of the concrete block.

Q: In a triangular channel, find the minimum specific energy of flow if its critical depth is 1.2 m A…

A: Given data- Critical depth = 1.2 m, To find - Minimum specific energy of flow,

Q: The U tube in the figure contains two liquids in static equilibrium. The water of density pw (1000…

A: Given- Density of water- ρw=1000 kg/m3,Density of oil = ρxl=80 mm,d=20 mm,ρx=?

Q: A single angle tension member, L 4 x 4 x 3/8 in. made from A36 steel is connected to a gusset plate…

A: We have to find out the adequacy of the given member. Gven data: db= 5/8 in For L4x4x3/8Gross area =…

Q: 2. In the following foundations, which one is limited by rigid angle ( A. Rubble foundation B. Cross…

A: Given, Multiple choice question related to foundation

Q: In Figure 1.2, get the specific gravity of the following common substances. Densities of Some Common…

A:

Q: The 222000-lb space-shuttle orbiter touches down at about 238 mi/hr. At 202 mi/hr its drag parachute…

A: Given: Initial speed Vo =238 mi/hr, Velocity while chute deployment, V1 = 202 mi/hr, final velocity,…

Q: SOLVE FOR EACH FORCE MEMBER OF THE GIVEN TRUSS. (USE METHOD OF JOINTS) E P₁= 30N P₂=15N P₁ A F -3m B…

A:

Q: o a uniform factored load of 50kN/m. The 300mm x 510mm beam (exposed to weather) is reinforced with…

A: According to given data  A 6-meter fixed-ended beam is subjected to a uniform factored load of…

Q: Using the arc basis, what is the degree of curve if the measurements of the middle ordinate is 2.0m…

A:

Q: The medium size of the sediment particles in an alluvial channel is 0.4 mm. For a 3 discharge of 4…

A: Given data- An alluvial channel- Size of particles d=0.4 mm, Discharge Q = 4 m3/s, To Find- The…

Q: A railroad intersects a curve highway AB. Distances along AB are measured along an arc. Using the…

A: Answer  Stationing at the intersection x = station at A + Length of curve AX Length of curve AX =…

Q: 2 m A G B 1m F 2 m C E 1 m. P3 D P2

A:

Q: Problem:5: Determine the horizontal and vertical reactions 60k > 3 6' 60k

A: Given data : A problem of structure analysis.

Q: The beam cross-section shown is design to resist a nominal moment Mn of 320 kNm, if f = 35 MPa and…

A: Given : Mn = 320 kN  f'c = 35 MPa and fy = 420 MPa This is a problem of R.C.C where we have to…

Q: A 500 lb/ft 10 ft C B 10 ft 3 k

A:

Q: At a point on a streamline, the velocity is 3 m/s and the radius of curvature is 9 m. If the rate of…

A:

Q: For each of the building properties listed below, identify which parameter from the base shear…

A: In a thoroughly supported study, the deformational characteristics and structural properties of the…

Q: H.W.15: For a simply supported beam with span 10 m, determine the area of steel required to…

A: Given:- The span length of the beam = 10 m  The dimension of the beam = 400×700 mm The magnitude of…

Q: (1) The watershed at a particular site on a river has 77000 ha area. The mean annual is 950 mm.…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: A 6º curve branches off from a 3º main curve in opposite direction in the layout of a BG yard. If…

A:

Q: 4. An open vessel 0.46-m in diameter, 0.60-m high and full of with water is rotated about its axis…

A:

Q: When a dolphin glides through air, it experiences an external pressure of 0.75 m of mercury. The…

A: Given: A dolphin glides through air, It experiences an external pressure of 0.75 m of mercury. When…

Q: Considering the beam loaded as shown below. Assume El = 50 000 kN m² What is the deflection at C? 0…

A: Given Data  EI = 50,000 KNm2 Find the deflection at C.

Q: A hydraulic jump takes place in a 6 m wide rectangular channel at a point where the upstream depth…

A: First we summarise the given data : Upstream depth = 0.5 m width of rectangular channel = 6 m…

Q: Using moment distribution method, analyse the continuous beam. [ El is constant throughout the beam…

A:

Q: A sewage treatment plant receives sewage at a flow rate of 5000 m³/day. The total suspended solids…

A: A )  Given data : Flow rate = 5000 m3/day TSS concentration = 200 mg/L Reduced TSS concentration % =…

Q: Please state are the three levels of structural seismic resistant design goal and the methods used…

A: The three levels of structural seismic resistant design goals are life safety, damage control and…

Q: Problem 34: Determine the maximum slope and maximum deflection for the beam shown figure by…

A: Given : This is a problem of Structure where we are asked to determine max. slope and max.…

Q: 1. Using either formula, double integration method, or area moment method, determine the maximum…

A: Given E=200GPaI=6×106 mm4 To find  Maximum deflection of beam

Q: completely mixed activated sludge reactor treating municipal wastewater, we can assume the following…

A:

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.