Answered: Given fıve resistors in parallel with…

Given fıve resistors in parallel with the following data, what is the total resistance? R1 = 41 ohms R2 = 17 ohms R3 = 96 ohms R4 = 25 ohms R5 = 70 ohms

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Combination Circuits

Section: Chapter Questions

Problem 1PA: A circuit contains a 1000- and a 300- resistor connected in series with each other. The total...

See similar textbooks

Related questions

Q: Determine the equivalent resistance between points a & b for the given resistive network. Each…

Q: What is the total circuit resistance if a 2-ohm resistor is added to the circuit at point A? 30 A. 1…

A: In this question we need to find a total resistance of the given circuit .

Q: The total resistance R (in ohms) of two resistors connected in parallel is given by 1/ R = 1/ R1 +…

A: Given; The total resistance R if two resistors are connected in parallel is 1R=1R1+1R2 And R1=10 Ω,…

Q: To convert a 2 mA meter with internal resistance of 120 ohm into an ammeter of range 0-200 mA, the…

A: Given: Meter resistance, Rm=120 Ω Meter current, Im=2 mA Measured current, I=200 mA

Q: Find the individual current and voltage drop across each resistors if C2= 48 12, C2 = 25 8 and…

Q: The three series resistors R1,R2 and R3, what is the value of resistor R1 if voltage V1=25 V and…

A: We will use ohms law to find unknown resistance. According to ohms law current =Voltage resistance.

Q: The total resistance R (in ohms) of two resistors connected in parallel is given by 1/ R = 1/ R1 +…

A: Given: Two resistors are connected in parallel. Formula and concept:

Q: Refer to Figure below, calculate; i. The total resistance ii. The total current and the branches…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: What is ammeter reading and value of R. Ammeter is ideal(given).

A: From figure all resistors are in parallel so voltage is same. Using ohms law we will find current in…

Q: a wire has a resistance R are cut into 2 pieces and the small pieces are connect in parallel…

Q: Determine the equivalent resistance between terminals a and b. R1 R2 R3 10 Ohms 20 Ohms 7 Ohms R4 -b…

A: When the 2 resistors are connected in series, The equivalent resistance is given by: When 2…

Q: Determine the equivalent resistance between terminals a and b. R1 R2 R3 a W 7 Ohms 2 Ohms 6 Ohms R4…

A: Given : In this question we have to apply The parallel and series combination of resistance concept…

Q: determine a) total resistance b) total current c) total current in 20 ohm resistor

A: Given : Brief description: In the above given question they want to know the value of total current…

Q: A circuit with R1= 1 Kilo ohm is connected in series with R2=3 Kilo ohm, if RL is attached in…

A: Resistance opposes the flow of current. Resistance is given by below relation R=VI where V is…

Q: "Resistors in Series and Parallel" PART1: The Resistors in Series Objective: To analyze the…

Q: Kirchhoff's Law Pls each question based on the table. 1. What can you say about the current (I)…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Given four 1ohms resistor. State how they must be connected to give an overall resistance of…

A: Solution 1) Req =1x1x1x11+1+1+1= 14Ohms Solution 2) Req=12+12= 1 Ohm

Q: The coil resistance of a microameter in the range of 50 microamperes is 2000 ohm. It is to be used…

A: the coil resistance of microameter in the range of given i=50μA, resistance r=2000 Ω =2 kΩ voltmeter…

Q: Resistor Resistance Voltage Current 1 100 Ohm 2 47 Ohm Total 10 V Complete the table by…

Q: Homeork-5: A resistor manufacturer produces carbon composition resistors of 100 MQ, with a tolerance…

A: A simple question based on colour coding of resistances. In this the given value is 100Mohm and the…

Q: How much voltage is required across a 56 Ohm resistor with a current of 5mA? a. 28 mV b. 280 mV c.…

A: Given data, Resistance of resistor, R=56 Ω Current, I=5 mA

Q: Three resistors are connected in series to a 25V-battery. The resistances are 8W, R. and 16W. If the…

Q: Four resistors R1=190 ohm, R2=330 ohm, R3=330 ohm and R4=50 ohm are connected to a 36 V battery as…

Q: A 3-0 light bulb and a 6-0 light bulb are connected in series with a 6-volt battery. a) What is the…

Q: 1000 resistors are connected in parallel, and their total resistance is 2 milli ohms. If the…

Q: Given two resistors in series with the following data, what is the total resistance in ohms? R1 =…

Q: Find the equivalent resistance at terminals A and B if each resistor is rated 1k-ohm. A B c-M- M- D…

A: consider the given question;

Q: A 10-ohm and 20-ohm resistance are connected in parallel. Another resistance of 5-ohm is connected…

Q: The provided 4-band resistor has the following color code . What is the tolerance value for this…

Q: (a) What is the resistance X of the resistor in the mid- dle if the equivalent resistance of the…

Q: All resistors in the circuit are the same measuring at 1 ohm at 25 deg celcius. At the same…

Q: Given 4 resistors each having a resistance of 1000 ohms, show how these resistors might be combined…

Q: Lab. #7 Current and OHM law 12. Calculate voltage Vi and current Ii for each resistor in following…

A: In this question, We need to determine the current and voltage across each elements. We know…

Q: 2. Calculate the total resistance: R? 4-ohm b 3 1-ohm

Q: 15. Two resistors R1 and R2 are connected in series and parallel. The values of the resistances are…

A: Firstly, Two Resistors R1 and R2 are connected in series RT=R1+R2 The uncertainty in combined…

Q: a Rat

A: we need to determine equivalent resistance.

Q: Three resistor are connected in parallel to a 20V-supply. The resistances are R1=100, R2=8 and R3.…

Q: (III) Two 9.4-k2 resistors are placed in series and connected to a battery. A voltmeter of…

A: It is given that: R=9.4kΩS=1000ΩVV=3 VVR=1.9 V

Q: Draw the circuit diagram and determine the equivalent resistance of 3 resistors rated as R1 = 5…

A: Given: The resistances are R1=5 OhmsR2=30 OhmsR3=60 Ohms

Q: Find the equivalent resistance of the network (i) when the switch is open (ii) When switch is…

Q: Vr1=4.135V Vr2=0.31V Vr3=20.55 V Vr5=20.76 pV if you put a multimeter with the black negative…

A: a multimeter is a device which can be used to measure the AC/DC voltage, current, frequency, and…

Q: 1. Three resistors 10 Q, 12 Q, and 15 2 are connected in parallel to a 12-volt source. Find a.…

Q: The three series resistors R1,R2 and R3, what is the value of resistor R1 if voltage V1=25 V and…

Q: Arrange six 10-ohm resistors to have a total resistance of 10 ohms.

Q: Theoretically calculate the equivalent resistance between points A and B. Measure the equivalent…

Q: A resistance arrangement of 50 ohm is desired. Two resistors of 100.0 ± 0.1 ohm and two resistors…

A: we need to find out the uncertainty for each arrangement.

Q: What should be the value of resistor R on resistor R? b) Find the maximum power transferred on…

A: The value of resistance R to maximum power transfer to load R Maximum power transfer?

Q: What is the resistance X of the resistor in the mid- dle if the equivalent resistance of the system…

A: Assume voltage at point A is 0 and at point B is 1 V. now write KVL at middle points and find…

Q: R1 R2 -a 1 Ohm 2 Ohms R3 3 Ohms R4 R5 -b 4 Ohms 5 Ohms

Q: Q1. A circuit with R1= 1 Kilo ohm is connected in series with R2=3 Kilo ohm, if RL is attached in…

Concept explainers

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.

Question

100%

Given five resistors in parallel with the following data, what is the total resistance?
R1 = 41 ohms
%3!
R2 = 17 ohms
R3 = 96 ohms
%3D
R4 = 25 ohms
%3D
R5 = 70 ohms

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

P-channel Metal-Oxide Semiconductor (PMOS), N-channel Metal-Oxide Semiconductor (NMOS), and Complementary Metal-Oxide Semiconductor (CMOS)

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circuit contains a 1000- and a 300- resistor connected in series with each other. The total circuit resistance must be reduced to a value of 1150 . Using standard resistance values of 5% resistors discussed in Unit 5, explain how to change the present resistance value to the value desired.
A 10,000- resistor has a tolerance of 5%. What are the minimum and maximum values of this resistor?
Two resistance are R1=10 ohm, tolerence5% R2=15 ohm, tolerance is 3% Determine the result along with tolerance if they are connected in parallel
What is the equivalent resistance of the circuit (Ohms) when R1 = 29 Ohms and R2 = 68 Ohms?
15. Two resistors R1 and R2 are connected in series and parallel. The values of the resistances are Calculate the uncertainty in the combined resistance for both the series andthe parallel arrangement D) For series connection, 0.1044 ohms For parallel connection, 0.1338 ohms
State the characteristics of voltage and current in a series circuit connection of resistors. State the characteristics of voltage and current in a parallel circuit connection of resistors. please explain it properly.
Determine the voltage across resistor 2, VR2with E=8V, R1=581 ohms and R2=750 ohms.
if an additional resistor with a value of 10M Ohms is placed in parallel with R1,R2, and R3, would you expect to voltage across R1,R2, and R3 to change?
From the figure, solve for the current and the voltage drop across each resistor. Let R1 = 1kΩ, R2 = 2kΩ, R3 = 3kΩ, E1 = 3 V and E2 = 6 V.
The color code of the following is Red-Black-Red-Gold. Solve for a) Resistance nominal value b) Measured Current c) Measured voltage. The multi-tester readings are shown below.
Two resistors R1 (100KΩ) and R2 (50 KΩ) are connected in series with a 150 Volt voltage source, if you want to measure the voltage at R2 with voltmeter 1 (sensitivity = 1KΩ/V) and voltmeter 2 (sensitivity = 20KΩ/V). Determine (a) the readings per voltmeter, (b) the percentage error of each reading. (make a picture of the circuit first).
if the resistor R1 and R2 terminals are connected across each and R3 is connected along single terminal. If the R1=5 R2=10 and R3=15 ohms, what will be the Rtotal?