Given:Internal pressure of the pipe = 2.943 MPa Thickness of steel pipe = 122.623 mm Situation 5Steel pipe having the diameter of 1 m. carries water under the head of 300meters of water.15. Compute the tangential force on the steel pipe.

Given data- Diameter (D) = 1 m Head (h) = 300 m Internal pressure of the pipe(P) = 2.943 MPa =…

Answered: Given: Internal pressure of the pipe =…

Engineering

Civil Engineering

Given: Internal pressure of the pipe = 2.943 MPa Thickness of

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem Number 6. A simply supported beam has a length of 4m. The beam is carrying a 500N downward…

A: P = 500 N M = 100Nm

Q: Q2) The areas within the underwater contour lines of a reservoir are as follows: Contour (m) 184 182…

Q: Use integration method The face of a vertical dam has the shape of an isosceles triangle of…

Q: The A dam has a semicircular gate with diameter 4 m Cop of the gate is 8 m below the surface of…

A: Given, The diameter of the semi circle = 4m It is at a distance of 8m from the top of the water…

Q: Construct moment diagrams for the beam using superposition method.

A: Cantilever beam To find: Moment diagram using superposition theorem

Q: Determine the strain energy of the beam shown in the figure below. The cross-section of the beam is…

Q: Radium decomposes at a rate proportional to the quantity of radium present. Suppose that it is found…

Q: A reservoir A, the free water surface of which is at an elevation of 275 m, supplies water to…

Q: Consider the following particulars in respect of a concrete mix design: Specific Gravity Weight 400…

A: To Determine Weight of fine aggregates.

Q: Q2: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

Q: diameter of 1 m. carrie wall thickness of steel p king stress for steel pip

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-seu beam is circular…

Q: Q1) The areas enclosed by contours in a lake and a hill situated side by side in a plot of land are…

A: Irrigation engineering : Irrigation engineering is the science of planning and developing an…

Q: 2. A 0.051 m diameter nozzle is attached to a hose with an inside diameter of 0.1 m. The resistance…

A: Apply continuity equation to calculate velocity. Then using Bernoulli equation calculate pressure at…

Q: Problem 3. Draw the shear and moment diagrams for the beam. 45 kN/m 30 kN/m C B -6.5 m- + -10 m- (c)

Q: Which one is the most efficient VOD (m/s) design for an explosive with a density of 1.6 gr/cc and…

A: ∈= 75.5 Gpa density of rock (γr)= 2.75 g/cc density of explosive (γe)=1.6 g/cc To find - VOD design…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-s beam is circular…

Q: 2. Determine the slope and deflection at point B of the beam AB shown using the Area- Moment Method.…

Q: 3. The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in…

Q: Determine the maximum bending moment along the length of the bear

Q: A * !!! 6m B 4.5m

Q: 23. Referring to problem 22, the value computed from the governing interaction equation or formula…

A: Pa = 1188KN

Q: If the 80kg ski-jumper attains a speed of 24.40 m/sec as he approaches the takeoff position,…

Q: For the beam subjected to the loadings as shown, determine the following: 52 kN 40 kN/m 2m 4m B 2m C…

A: a. draw the shear and moment diagrams specifying values at all change of loading positions and at…

Q: What is the terminal velocity (m/s) for a 4g particle which is falling in the water with projected…

A: Asked: To compute the terminal velocity of the particle falling in water. Given: Mass of the…

Q: Q1) A railway embankment, 12 m wide, with side slop 11 2:1 is to be calculated for its volume of…

Q: Using the slope-deflection method, draw the bending moment diagram. 3m 3A 4m 20km 2EJ 3€] D

Q: m Number 5 f = 8m alculate the force at member GH 1.859KN T 1.859KN C 1.371kN T 1.371kN C 1 kN D 1…

Q: with a factor of safety of 3. Then, to the ground c) Comment on any differences for the computed…

A: Given: The factor of safety is 3. Consider the figure,

Q: 13. Does negotiation require both parties to compromise to come to an agreement? Why or why not?

A: Negotiation is a planned debate that addresses a perceived problem that is agreeable to both sides.…

Q: Obtain 0.5 Hr- UH from 2 Hr UH using S-Curve having Base Flow 8.900 cfs and catchment area 6526000…

A: Given: As Base flow is mentioned hence given hydrograph is Flood Hydrograph Time Runoff (cfs)…

Q: A 466-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

Q: STA. B.S. F.S. 1 5.87 2 7.03 6.29 3 3.48 6.25 4 7.25 7.08 5 10.19 5.57 6 9.29 4.45 7 4.94 For…

A: Lets using Rise/Fall method B.S - F.S = Rise/Fall Positive difference mean rise Negative…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section of the beam…

Q: Determine the value of Support Reaction B 400 N/m B 1m + 3m 2m 200 N

Q: 17. Determine the vertical deviation at the point where the 100N-m moment is located relative to the…

A: Determination of vertical deviation at point where 100 KNM moment located relative to tangent drawn…

Q: 4.Compute for the tension load, T in kN that can be applied in the 8mm thk plate considering the…

Q: Outline city and regional planning and land use strategies

A: City and regional planning:- City, as well as Regional Planning, is indeed a field of study that…

Q: For deflection y units in a beam which of the following relation holds good? OⓇ = dy/dx de/dx =…

A: deflection in beam is equal to y Questions is from structural analysis here the defection in beam is…

Q: 3- For the beam given in the figure, a- Draw the elastic curve by using the Mohr Method. b-…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section of the beam…

A: Determine the strain energy of the beam shown in the figure below.

Q: 10 k A ←6 ft- 8 -12 ft- 0.8 k/ft |C -12 ft

Q: SOON - 2m 450 N 10m 1.01 (d)

Q: Water is pumped between two reservoirs at 0.25 m³/s through 800 m of 250 mm diameter pipe and…

Q: Solve for moment at A and D

Q: governed? Write down the well-known amete

A: Introduction the turbomachine are gadgets in which energy is moved consistently streaming liquid by…

Q: illustrate and explain how a congestion charge levied on motorists works using a diagram

A: The Congestion Charge is any amount daily tariff and payment enables motorists to drive around,…

Q: Problem 2. Determine the equations for shear and bending moment for the beam shown. 45 kN/m 30 kN/m…

A: Shearforce : Clockwise positive Anticlockwise negative Bending moment : Clockwise negative…

Q: What are the underlying assumptions when calculating for the upper and lower bounds of the elastic…

A: he lower-bound estimate of elastic modulus is calculated by: Ec = 1 / (ff / Ef + (1 – ff) / Em). On…

Q: The steel truss was subjected to horizontal force 2kN at C. Find the member forces of AC using the…

A: Calculation of Member forces in AC using Unit Load METHOD##

Question

Given:
Internal pressure of the pipe = 2.943 MPa
Thickness of steel pipe = 122.623 mm

Situation 5
Steel pipe having the diameter of 1 m. carries water under the head of 300meters of water.
15. Compute the tangential force on the steel pipe.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft 70 mm in diameter is being pushed at a speed of 400 mm/s through a bearing sleeve 70.2 mm in diameter and 250 mm long. The clearance, assumed uniform, is filled with oil at 20 C with v=0.005 m^2/s and sp.gr.=0.9. Find the force exerted by the oil in the shaft.
Determine the maximum horsepower a solid steel shaft 2.25in in diameter can transmit at 250rpm if the working stress in shear is 11,000lb/sq.in.
Replace the loading system by an equivalent resultant force and couple moment acting at point O
The rectangular gate has dimensions: h=.8m; b=2.4m;c=0.4m;weighs 2 tons. It slides on a plane of inclination θ=70° and serves to plug the conduit of a dam. Considering that the coefficient of friction is 0.35. Determine the magnitude of the tension T needed to move the gate when the water level reaches the elevation of 62 m.
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.
An open tank in the shape of frustrum of a cone is bound by two hoops one at the top and another at the bottom. The diameters at the top and bottom are 2m and 3m respectively. If total busrsting force is to be taken care if by the hoops, find the tension in each hoop if water stands 2m in the tank. Height of tank is 3m.
Find the Maximum Shear andMoment.? can you solve in 20 mins?
Consider the ¼-circular curved gate hinged below. The gate radius is 3 m,its width (into the page) is 5 m, and its weight is negligible. Obtain the forcemagnitude Q so that the gate remains closed as shown. The specific weight of the water is γw = 9.81 kN/m3. Please show all working and free body diagrams and explain clearly.
AB, a rectangular (0.6 mx0.9 m) sluice gate, blocks a liquid with a gravity of 0.79. The weight of the floodgate is 300 N, and find the force that must be applied to the Cable BCD to open the surface Please tell me the process of solving
Consider the ¼-circular planar gate hinged below. Its radius is 3 ft and itsweight is negligible. Obtain the force magnitude R so that the gate remains closed as shown. The specific weight of the water is γw = 62.4 lb/ft3 Please explain clearly and show all working and free body diagrams. Thanks.
A circular gate 1.5 m in diameter is inclined 45 with the vertical. The center of the gate is 10m below the water surface. a. Calculate the total force on the qate b. Calculate the distance of the total force from the bottom of the gate, c. If the gate is hinged at top, find the normal force applied at the bottom required to open the gate.
QUESTION-1: Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)