= Given: Retaining wall with soil provide shown and the following relevant properties: q' = 25°, y = 18.7 kN/m³, Ysat 23 kN/m³ Find: Compute the lateral pressure distribution and magnitude and location of resultant force acting on the cantilever wall with the groundwater at locations "a" and "b" using the Rankine theory of lateral earth pressures. dihidale entraaTO 70 VIRU 7m 3.3 m b 7 8.4 m

= Given: Retaining wall with soil provide shown and the following relevant properties: q' = 25°, y = 18.7 kN/m³, Ysat 23 kN/m³ Find: Compute the lateral pressure distribution and magnitude and location of resultant force acting on the cantilever wall with the groundwater at locations "a" and "b" using the Rankine theory of lateral earth pressures. dihidale entraaTO 70 VIRU 7m 3.3 m b 7 8.4 m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter13: Retaining Walls

Section: Chapter Questions

Problem 13.6P

See similar textbooks

Similar questions

a. Rankine's active earth pressure coefficient: ka1 = (for the upper layer) ka2 = (for the lower layer) b. Lateral pressure due to soil (in kN/m2 per meter length of wall): @ point R = @ just above point S = @ just below point S = @ point T = Thank you please help
Figure Question 2 depicts the design of a gravity retaining wall for carthquake condition given: Kv-0 and Kh-0.37 What should be the weight of the wall for a zero-displacement condition? Use a factor of safety of 2.4. What should be the weight of the wall for an allowable displacement of 50.95 mm? Sand $:= 35° %3D Sand $=37 3. Figure Question 2 B Give a comprehensive detail on how to analyze a retaining wall
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute TOTAL LATERAL FORCES in the 2nd floor? B. Compute LATERAL FORCES in the 3rd floor?
Given The uniformly loaded area shown below is built on the ground surface and carries a load of 160 kPa. D1-8 m D2 = 12 m D3 = 4 m D4-5 m D5 = 3 m D1 D3 D2 D5 A D4 Required Determine the vertical stress increment at a depth of 10 m below Point A. Provide answer in kN/m², to the nearest 100th.
Question 1: You are designing a retaining wall at the construction site. The friction angle of sand backfill is 28". Define the active lateral earth pressure coefficient based on Rankine's theory. Show your work and select the closest value: a) 0.30 b) 0.35 c) 0.40 d) 0.50
1.) A house is being built on the soil profile shown below bears at the depth shown. The surface loading created by the house is 1500 psf. Draw the o, o', u, profiles with depth and show values at depth shown. In addition, calculate the load on the basement wall with Ko = 0.35. Depth (ft) Sand Ya = 110 pcf Y = 116 pcf 7 ft 10 Clay = 119 pcf 40 Sand = 118 pcf
A retaining wall is shown in the Figure below. For each problem, determine the Rankine active force, Pa, per unit length of the wall and the location of the resultant. H 12 m H₁ 4m Surcharge Frictionless wall Sand 71 di =0 Y₁ Y₂ 17 kN/m² 23.2 kN/m² ↓ Groundwater table i(deg) : (deg) 36 42 4 25 kN/m² Sand Ey (saturated unit weight) DE MOITAMINE 72 -0
The channel section shown is subjected to a vertical shear force of V = 29 kN. Calculate the horizontal shear stress Ta at point A, and the vertical shear stress tR at point B. Assume a = 50 mm, b = 250 mm, tw= 16 mm, t;= 12 mm, d = 74 mm. V | tw Answers: TA = MPa TB = i MPa
4- A moderately curved channel with a slightly rounded non-cohesive bed material with a diameter of d50 = 25 mm carrying a discharge of 30 m³/s. The longitudinal slope of the channel is 0.001 and the side wall slopes are designed to be 60% of the angle of repose of the bed material Note: Use the Strikler's formula to calculate Manning's value. Use the Swammy and Mittal's formula to estimate the critical shear stress. Use the free board depth of 0.5m. a) Design the channel using the tractive force method for a Boly ratio of 20 b) Design the channel using the most efficient hydraulic section c) Discuss about the channel stability and erosion for both designs in parts a and b Strickler (Chow, 1959) proposed a correlation between the mean diameter of bed material, dso, and the Manning's coefficient as: n = 0.039d¹/6 Swamee and Mittal (1976) proposed an explicit equation to express the Sheild's curve defined as: 50 0.409d² 1/2 (1+0.177d² )¹/¹² T = 0.155+.
4- A moderately curved channel with a slightly rounded non-cohesive bed material with a diameter of d50 = 25 mm carrying a discharge of 30 m³/s. The longitudinal slope of the channel is 0.001 and the side wall slopes are designed to be 60% of the angle of repose of the bed material Note: Use the Strikler's formula to calculate Manning's value. Use the Swammy and Mittal's formula to estimate the critical shear stress. Use the free board depth of 0.5m. a) Design the channel using the tractive force method for a Bo/y ratio of 20 b) Design the channel using the most efficient hydraulic section c) Discuss about the channel stability and erosion for both designs in parts a and b Strickler (Chow, 1959) proposed a correlation between the mean diameter of bed material, deo, and the Manning's coefficient as: n = 0.039d¹/6 Swamee and Mittal (1976) proposed an explicit equation to express the Sheild's curve defined as: T = 0.155+ To 50 0.409d² (1+0.177d²)
Soil Ysat = 125.0 pcf 2 ft 3 ft Datum B Determine the effective vertical stress (psf) for point D. 1 ft 5 ft ц ш о O D A 00 13 ft
Example: Please find the earth pressure at rest distribution value and resultant force on the retaining wall in the figure below; The static side pressure coefficient is 0.5 q=20kpa r=18kN/m rsat=18kN/m c=0kpa shared by H 10m