Given that the time constant's theoretical value is 150.8s, and the percentage error is 0.5%, what is the time constant's experimental value?

Q: If by actual count at the final pressure reading there are 40,000 particles greater than 10 microns…

A:

Q: Calculate the young’s modulus from one of these two graphs?

A:

Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…

A: In the given parameters, K refers to thermal conductivity of the material. It represents the ability…

Q: Describe with the aid of suitable diagram and show how the piezoelectric property of a quartz…

A: They discovered that applying mechanical pressure to select crystals like quartz released an…

Q: Semiconducting properties are associated with...

A: The correct option is first Alumina Al2O3 ceramics

Q: How can you express the equations of compatibility? Give examples of engineering designs in which…

A: given; (i) equation of compatibility? (ii) example of engineering designs in which torsion occurs.

Q: What is self-heating in strain gauges? Why is it caused and what are its implications on end result?

A: While there are several methods of measuring strain, the most common is with a strain gauge, a…

Q: mechanical vibration in damping elements

A: THERE ARE VARIOUS METHODS IN SOLVING MECHANICAL VIBRATION IN DAMPING ELEMENTS ..... 1.  NEWTONS…

Q: If the vapor pressure of moisture in the food is equal to the vapor pressure in the surrounding air,…

A: No drying of food will occur as vapour pressure is same and hence no evaporation of vapour will…

Q: Indicate the reasons and effects that deviates the normality graph, explain with examples. 4F mun 4F

A: Given: Here,→Given Normal distribution is non symmetric about  its mean→It is positively skewed

Q: O Formability and strength of surfaces will help reduce wear. O Modulus and high melting point of…

A:

Q: Your answer must be at least 250 words. Which of the gerrymandering techniques is the most fair? Is…

A: Gerrymandering is the political manipulation of election district lines in representative…

Q: The mechanical properties of materials is dictated by atomic bonding and

A: The mechanical properties of materials is dictated by atomic bonding and

Q: Explain the various errors during measurement. What are the causes of these error? How to eliminate…

A: Given Data⇒ Errors during management Causes of error Elimination of error

Q: 2. The specimen heated indirectly via a water bath, why? 3. What is the principle methods of thermal…

A: Answering question 2 and 3 If you want another question to be answered, please repost the question…

Q: What do you mean by spin, precession and gyroscopic planes? Explain.

A: The answer is

Q: Explain the theory of the Joule Thompson effect and give examples.

A: Joule Thompson effect states that if the real gas flow through pressure reducing valve then with the…

Q: 0. Which measuring instrument should be preferred to convert qualitative measurement with…

A: Thermochromic Liquid crystals -  TLC technique is a semiinvasive  thermal detection detecting. It…

Q: Can we apply the principle of virtual work as a method of virtual displacements?

A: The virtual work is applied where the several bodies or members of a same body are having a relative…

Q: Explain how physical quantinties are related to biomedical equipment are measured

A: Given Biomedical equipment To find Physical quantities

Q: What is the shear modulus and how can it be obtained from a torsion test

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: For an x-radiographic inspection of the plate in Figure 1 using a 100-keV beam. Calculate the change…

A:

Q: The mass of water in a single popcorn kernel was found to be 0.905 grams after it popped at a…

A:

Q: In the calculating of heat transferred in calorimeters, why is it that the equilibrium temperature…

A: The temperature distribution represents the temperature at finite points on the surface. The…

Q: Determine the values of VT for temperatures of 40C.

A:

Q: [Mechanical Engineering] Explain the phenomenon of material-tissue interaction following the…

A: Tissue engineering is an interdisciplinary discipline that combines biological and technical…

Q: in The pattern is dipped into a slurry of refractory material such as very fine silica and binders,…

A: In ceramic mold casting, there are two different type of slurries used which are know as true…

Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…

A: In the given parameters, K refers to thermal conductivity of the material. It represents the ability…

Q: A sample of heated metal is added to a coffee-cup calorimeter. What part of the setup functions as…

A:

Q: What is the apparent viscosity (Pa.s) of blood that is experiencine a shear rate of 52 s^-1? Assume…

A: given;⇒shear rate=52  s-1⇒yield stress (τ)=0.005Pa⇒apparent viscosity(μ)=?

Q: Consider the osmotic pressure-mediated nuclear compression under various concentrations of…

A: Given : V = 1500 μm3 Vf = 1000 μm3 10% PEG solution To find : Bulk modulus

Q: What is the relationship between angular velocity and radius (string length)? What is the…

A: Angular velocity is measured in rad/s. It is represented by the symbol omega .

Q: A particular device needs to be made that will experience a change in temperature of 100 °C. Two…

A:

Q: Tunneling is a small change from the simple particle in the box model that makes it much more…

A: Tunnelling is a phenomenon of quantum mechanics when a particle is trying to penetrate through a…

Q: 40 cm. 2 cm Figure 9.12: What is the mechanical

A:

Q: Calculate the energy cost of an electroplating process running at 0.54 V and 36.2 A for 3120 s…

A:

Q: How do you add two harmonic motions having different frequencies? - In vibration analysis, can…

A:

Q: Q3/ the table below show the properties of three materials suggest to applicate as tooth filling…

A: As we know, the physical property of the tooth filling:- -It can be a low value of the thermal…

Q: What is the torque applied, in Nm, to a 91 mm shaft if the resulting shear stress on the outside…

A:

Q: If the wrought stock material costs $60 per kg, what is the lost value due to the material removed,…

A: The cost of the wrought stock material is C1=$60 /kg. The cost of the scrap material is C2=$3 /kg.…

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.