ENGINEERING MECHANICSUPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS. NO LONG EXPLANATION NEEDED. ANSWER IN 2 DECIMAL PLACES. Given the diagram below, determine the following:3 m2m8Fim1.5m.1.5m.3 kN1.5 m4 kN2mA. Vector form of position vector CB (in m).B. Vector form of position vector DA (in m).C. Magnitude of the moment (in kN-m) due to the 3kN force about point D.D. Magnitude of the moment (in kN-m) due to the 4kN force about point C.

Answered: Image /qna-images/answer/df59cd65-fdea-4982-9307-1f6e0776875e.jpg

Given the diagram below, determine the following: 3m 2m m Im Fim1.5m. -1.5m 1.5m 5m 3 kN 3 m 4 kN 2m A. Vector form of position vector CB (in m). B. Vector form of position vector DA (in m). C. Magnitude of the moment (in kN-m) due to the 3kN force about point D. D. Magnitude of the moment (in kN-m) due to the 4KN force about point C.

Given the diagram below, determine the following: 3m 2m m Im Fim1.5m. -1.5m 1.5m 5m 3 kN 3 m 4 kN 2m A. Vector form of position vector CB (in m). B. Vector form of position vector DA (in m). C. Magnitude of the moment (in kN-m) due to the 3kN force about point D. D. Magnitude of the moment (in kN-m) due to the 4KN force about point C.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
‏A simply supported beam is subjected to two forces P and Q. Value of force P is 20 N and value of force Q is 40 N.If value of support force Ra is 30 N , then value of support force Rb is calculated as : O a . 70 N O b.30N O C60N O d . SON
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
The process of splitting a force into its component forces is called ____________ Select one: Resolution of forces Splitting of forces compounding of forces Composition of forces
A small piston of a hydraulic press has an area of 20.0 cm^2. If the applied force to the piston is 75.0 N, what must the area of the connected large piston be to exert a force of 6550 N? d. 1180 cm^2 e. 1450 cm^2 a. 1550 cm^2 c. 1250 cm^2 b. 1750 cm^2
In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and 100 cm. Find the distance moved by the load piston if 10 strokes are applied to the effort piston . Given : Stroke length of the effort piston is : 50 cm . Distance moved by Load piston : ____________m
Include the free body diagram The diameters of a small piston and a large piston of hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied in the small piston. Find the load lifted in N by the large piston when the piston are on the same level.Take density of the liquid in the jack is 1000 kg/m^3. a. 1625 b. 1520.5 c. 1500 d. 1600
a drum has gasoline s.g=0.9, with oil s.g=0.8 and sea water s.g=1.03. the depth of the liquid is 0.8m, 0.5m, and 1.0 for gasoline, oil and sea water.1. find absolute pressure at depth 1.2m 2.find the depth at 1.8m 3. find the force F at depth 2.1m when diameter of drum is 0.5m
A submarine is traveling at a depth of ‘95’ kilometers in the ocean, where the gagepressure is 840 Kg(f)/cm2 . The density and bulk modulus of elasticity of water at the top surface of the ocean are 1025 kg/m3 and 24000 kg(f)/cm2 respectively. Find the following:(i) What will be the density of water at the depth of 2.0 kilometers?(ii) What will be specific volume and change of volume at that depth?(iii) What is the pressure at the top surface of the submarine? How much will bechanged in pressure if submarine change direction from North to East?
Fluid mechanics [Rotation and Translation of Fluid Masses] An rectangular tank with a width of 1.5 m, a length of 3.0 m, and a height of 2.0 m is filled with a liquid (sg = 0.8) to a depth of 1.5 m. The tank is accelerated along its length by a magnitude of 2.5 m/s2. Determine the forces acting on (a) the leading side of the tank, and (b) the rear end of the tank. Find the:a. lead side =__________kN b. rear side =__________kN