Pls answer and show solution ty Given the figure below, Solve for the following unknowns.17 mRA, -RA, -1212 mDetermine the Reactions and Moments in kN and kN.m. respectively.MA35 kN/m245 KN RA,=RA, =MA=RB, =RB,Ma

Answered: Image /qna-images/answer/a724fa49-1461-4789-bc04-b74650d94021.jpg

Answered: Given the figure below, Solve for the…

Given the figure below, Solve for the following unknowns. 17 m A 12 m B 35 kN/m 245 KN Determine the Reactions and Moments in kN and kN.m. respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 6 kN/m 4 m B 3 m *Assume A and C to be hinged supports, and B to be a pinned connection.

Q: A liquid has a specific weight of 48 lb/ft^3 and a dynamic viscosity of 3.05 lb-s/ft^2. What is the…

A: Given : Specific weight of liquid , Y = 48 lb/ft3 Dynamic viscosity, µ = 3.05 lb-s/ft2 Required :…

Q: 3. The transparent "biospheres" beneath the Bay of Noli, in Savona, Italy, are part of the…

Q: A force Pacts on the frame shown at point E. Knowing that the absolute value of the moment of Pabout…

A: Determine the magnitude of the force P.

Q: Problem 4: Total stress, pore pressure and effective stress A soil profile is shown in the following…

A: Given data Dry density of sand (yd) = 16.5 KN/m3 Sarurated density of sand (ysat) = 19.25 KN/m3…

Q: The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the…

Q: Percentage finer by weight 100% 80% 60% 40% 20% 0% 0.001 H 0.010 Soil Sample ID H I J L #200 0.100…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: T 2 m 3 kN 2 m G LEX -3 m -1.5 m- (b) *Assume A to be hinged and D to be roller. 6 kN F 3 m- -3 m- 3…

A: To Determine :- The support reactions and member forces on the truss.

Q: Determine the LRFD design strength (kN) of the compression member shown. The distance between the…

A: Given, L = 282 cm or 2820 mm Fy = 345 MPa W360 x 72

Q: A river has ultimate BOD of 60 mg/L, a width of 20 m, a depth of 5 m and a flow rate of 9 m3/s. A…

A: The given data is shown below: BOD=60 mg/LWidth=20 mDepth=5mFlow rate=9 m3/sTemperature=20°CUltimate…

Q: The liquid limit and plastic limit of a soil are 60% and 30% respectively. If the natural water…

Q: illustrate/give examples of one truss, one rigid frame, and one beam that would satisfy the…

Q: Water is to be moved from one large reservoir to another at a higher elevation as indicated in the…

Q: pressure

A: takeγw=0.0361272lbin3γhg=13.60.0361272lbin3γoil=0.690.0361272lbin3

Q: Section 4.5 4.6 through 4.28 Determine the force in each member of the truss shown by the method of…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

Q: Determine the vertical reaction at the roller support. 3 m 43.8 kN/m, -7.2 m- 29.2 kN/m 222.5 kN…

A: Divide the distributed loading into a uniform load and a triangular load. Calculate their resultant.…

Q: Problem 3 The following data shows the results of the liquid limit and the plastic limit test a.…

A: Given: Liquid limit(LL) = 43 For test no.-3 to determine liquid limit: Wt. of wet soil + Wt. of…

Q: 6. Classify the foloowing soils according to the AASHTO classification system and give the group…

Q: A waste of 600 m³/hr flow rate with an ultimate BOD20 = 140 mg/l is to be treated in an activated…

A: According to given data A waste of 600 m³/hr flow rate with an ultimate BOD20 = 140 mg/l is to be…

Q: Classify each of the trusses as statically determinate, indeterminate, or unstable externally.…

A: Solution: Check for the determinacy of the truss: Number of members, m = 13 Number of reactions, r =…

Q: Natural gas FLO 3 14 in 6 in -Mercury SG= 13.6 -Air 2 in 22 in Water

A: Given data:- The local atmospheric pressure is, =14.2 psi The given specific gravity of mercury,…

Q: Water is supplied at 150 ft³/s and 61 psi to a hydraulic turbine through a 3-ft inside-diameter…

A: Given: Required: Power loss in hp

Q: Using Area-Moment Method, determine the deflection at the overhanging end in mm. Given: P = 4.2kN…

A: Given data E = 10 GPA = 10 × 103 N/mm2 I = 20 × 106 mm4 Find deflection at overhanging end…

Q: A cantilever beam has the cross-section of an isosceles triangle and is loaded as shown below: T1mL…

A: Beam is subjected to uniform moment, M. Bending stress can be found using MoI , Moment value and…

Q: A triangular irrigation lined canal carries a discharge of 25 m³/s at bed slope = 1/6000. If the…

Q: What is the difference between charpy impact test and izod impact test?

A: Difference between Charpy and Izod impact test

Q: 오 A 3m SOKN ↓ 3m B J Hinge 10KN/M qm - ㅇㄹ C

Q: A very wide rectangular channel carries a discharge of 8 m³/s per metre width. The channel has a bed…

Q: Water flows steadily from a nozzle into a large tank as shown in the figure below. The water then…

Q: 113. Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…

Q: Determine the moment at B for the beam shown.

A: ###DETERMINATION OF MOMENT AT B USING 3 MOMENT EQUATION METHOD ####

Q: An aluminium shaft with a constant diameter of 50 mm is loaded by torques applied to gears attached…

Q: For fully submerged: - compare the results of W x r with the calculated values of F x (Xcp + hs). -…

Q: A particle moving in the x-y plane has a position vector given by r = 3/2t² i + 2/3t³j, where r is…

Q: A statically determinate pin-jointed truss system is shown in Figure Q3. The member sizes are 50 mm…

A: Given : 1. uniformly distributed load =10kN/m 2. span length AB= 6m 3. length of member :…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: a). Determine the atomic and equivalent weights of Na+ and Ca2+. A water sample contains 102 mg/l…

A: Answer (a) For Sodium Na+ Atomic weight(AW) of Na+ = 23 g Na+/ mole Equivalent weight(EW) of Na+ =…

Q: 5-27. Determine the reactions acting on the smooth uniform bar, which has a mass of 20 kg.

A: Given : Mass = 20 kg Determine the reaction acting on smooth uniform bar?

Q: The box at B weighs 50-lb. Assume that there is enough friction to prevent slip at B. The plank…

Q: Determine the magnitude of the component force F in Fig. 2-13a and the magnitude of the resultant…

Q: A rectangular beam has b = 310 mm and d = 460 mm. The beam will be designed to carry a service dead…

Q: Water is to be pumped from the large tank shown in the figure below with an exit velocity V₂ of 5.7…

Q: A rectangular open channel needs to be designed to carry a flow of 2.0 m³/s under uniform flow…

Q: An HSS 10 x 6 x %/16 with F, = 46 ksi is used as a column. The length is 15 feet Both ends are…

Q: A w B

A: Given : P = 13 Kn w = 10 kN/m To Find :

Q: What is the number on the last part of the bending moment where it says 30 x ....

A: Given data:

Q: Water is supplied at 180 ft³/s and 67 psi to a hydraulic turbine through a 3-ft inside-diameter…

Q: (Situation 1) Determine the support reactions on the following structures: (a) cont -6 ft- 5k/tt -12…

A: A loaded beam is given and it has been asked to determine support reactions. Please refer step 2 for…

Q: Determine all force of the member Fig. A 3 Noten: Tension force (-) [T] Compression force (+) [C] 8…

Question

100%

Pls answer and show solution ty

Given the figure below, Solve for the following unknowns.
17 m
RA, -
RA, -
12
12 m
Determine the Reactions and Moments in kN and kN.m. respectively.
MA
35 kN/m
245 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the magnitude of the moment (Nm) of the force P = 361 N about the z-axis. Round off only on the final answer expressed in 3 decimal places.
SOLVE FOR REACTIONS, use Area Moment Method answers should be: RA = 44.269 RB = 67.894 RC= 2.163
Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction of all reactions in the positive direction of y axis. Enter your answer in kN to two decimal places.
an overhang beam is situated above a cantilever beam carrying its roller support. determine the absolute value of vertical reaction at A, B,C,D,E.(in kN)
The magnitude of the force Qis 736 N. Determine the magnitude of the moment (Nm) of Q about point C. Round off only on the final answer expressed in 3 decimal places.
The magnitude of the force Qis 592 N. Determine the magnitude of the moment (Nm) of Q about the line CF. Round off only on the final answer expressed in 3 decimal places.
In the figure below, given P1=10, and W=7, write the equation for moments that you need to estimate the moment's magnitude at C. Estimate the moment at C and place the magnitude in kip-ft as the answer. Do not forget to place - for negative moments.
A propped beam is shown in the Figure. It is loaded with a concentrated moment at the propped end causing a 1-unit rotation at that end. Assume EI – 1,200kN.m2.Find the moment M and the moments at the fixed end. Find the reaction at the propped end.
Solve for the reactions and draw the shear and moment diagrams of the following beams using both Three-Moment Equation (3ME) and Slope Deflection Method (SDM) for this beam. W = 12 , P = 57 , EI = constant
Determine the member end moments and reactions for the frames shown by using the slope- deflection method. Note: Use the 100 kN ∙ m acting at joint C for Equilibrium Equation at the joint, not on FEM’s.
The bar system given in the figure above, (between AB: 1m / BC between: 3m / CD: 2m) a) Show the support reactions and load occurring on the rod. b) Do you calculate support reactions? c) Calculate the Normal Force, Shear Force and Moment values by cutting from the points you have determined. d) Draw cross-section impact diagrams? Do you specify the maximum positive and negative moment values? e) Check the cross-sectional influence diagrams with a simple method, briefly explain the control steps.
Determine the magnitude of the resultant moment (Nm) produced by forces P = 660 N and Q = 364 N about point O. Round off only on the final answer expressed in 3 decimal places.