Given the following end-sections of a 15-m wide road whose side slope is 1.5:1. 5 8 4 4 + 580 4 + 450 Cross-sectional area at mid-station is equal to Select the correct response: 180.61 sq.m 147.39 sq.m 150.65 sq.m 118.66 sq.m CO

Given the following end-sections of a 15-m wide road whose side slope is 1.5:1. 5 8 4 4 + 580 4 + 450 Cross-sectional area at mid-station is equal to Select the correct response: 180.61 sq.m 147.39 sq.m 150.65 sq.m 118.66 sq.m CO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given the following level section notes for stations 1+120 and 1+160: 1+120 | 6.6 | 0 | 7.6 | 0.8 |…

A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Compute the end area of the irregular cross-section described below: Width of Road = 9 meters 3.8…

A: Solution Cross-section of the earthwork is drawn below. All the areas are fill areas. Width of road…

Q: Town A and B are on the opposite sides of a river .The towns are to be connected with a bridge CD…

A: The figure drawn from the given information is shown below.

Q: LINE BEARING DISTANCE N 75°30' W S 60 °30' W N 43 ° 50' E N 35 °20' E ST 385.00 TU 360.00 UV 522.10…

A: Sign conventions: NE = Both positive SE = Lattitude negative Departure positive SW = Both negative…

Q: Water is to be transported at a rate of 2 m3/s in uniform flow in an open channel whose surfaces are…

A: Given Data: The rate of flow in the open channel is Q=2 m3/s. The channel is surfaced with asphalt…

Q: Congestion mitigation policies can themselves influence the "timing" of rural space. (A) True B)…

A: The statement is TRUE. CONGESTION MITIGATION ALLOWS THEM TO provide jam free traffic , crowded free…

Q: Three level lines established on three different routes to established benchmarks, the result of…

A: Data Given: Route 1Elevation of BM1 = 30.162 mElevation of BM2 = 69.258 m above BM1Elevation of BM3…

Q: 2. It is desire to measure angle AOB with the transit at 0, but due to the fact that 0 is a swamp,…

A: As Per Guidelines , I can Only solve first part.

Q: ) Discuss classification of highways very briefly with neat sketches? (b) Discuss…

Q: 3.) In a certain portion of road to be constructed the following data were taken. Compute the volume…

Q: A surveyor measured the road frontage of a parcel of land and obtained a distance of 327.36 ft.…

A: Given data:- In surveying we study leveling, to measure levels of different points with respect to a…

Q: Explain the various types of surveys to be carried out before planning a highway system for a given…

A: 1) Map study 2) Reconnaissance survey 3) Preliminary survey 4) Location and detailed survey

Q: Q2/ The cross-section areas at river miles 52.5, 53.0, 53.5, 54.0, 54.5, 55.0 and 55.8 are,…

A: Given- A1=52.5 ft2A2=55.8 ft2QAVG=35.8Cfs

Q: 6.45 4.5 1 + 020 +2.3 +1.5 +1.0 6.0 6.9 1 + 040 +2.0 +1.2 +2.6

Q: For the given road cross section notes, the width of the road is 11.00 meters with SSof 1:1. Find…

Q: Given are the end-sections of a proposed 15-m wide road with side slope of 1.5:1. station 1 + 234:…

A: Formula used: A=w4hL+hR+c2dL+dR Calculating area: For…

Q: A series levelling had been down along the centre line of the proposed road the distance between…

A: Leveling is defined as the process of calculating the reduced level of a point either on earth or…

Q: What are the various surveys to be carried out before planning a highway system for a given area?

A: The various type of surveys for the planning of a highway system for a given area is as follows.…

Q: Problem 3: LINE BEARING DISTANCE ST N 75°30' W 385.00 S 60 °30' W N 43 ° 50' E N 35 °20' E TU 360.00…

Q: How do you describe the problem of designing a highway route location analytically?

A: Majorly there are 2 different ways for designing highway routes (i) Analytical hierarchy process…

Q: Station 4 + 940 Base= 8m; Side slopes= 1.5:1 1.84 1.22 0.42 Station 5 + 005 Base= 9m; Side slopes=…

Q: A series levelling had been down along the centre line of the proposed road the distance between…

A: Given that:

Q: Given the following cross-sections. Determine the corrected volume between stations 1+160 and 1+185,…

A: Solution STA 1+160 Width of the road = 10 m Side slope =1.25:1 So distance of section at depth =…

Q: The grading works of a portion of the proposed expressway shows the following notes. Limits of free…

A: ANSWER: Volume of waste = 1898 m3 solution attached below

Q: Three level lines established on three different routes to established benchmarks, the result of…

A: Given:- The results of the three-level lines established on three different routes to established…

Q: Q2: From the following excerpt of field notes, plot the cross section on graph paper and superimpose…

A: We have to determine the area by coordinate method as per the given data like slope 3:1 and subgrade…

Q: 24 cfs of water flows in a 4 ft diameter sewer pipe. Determine the depth of flow if the slope is…

A: Consider the given data Diameter of pipe=DD=4 ftQ=24 cfsSlope=SS=0.001 As we know that, We have a…

Q: A section of road between Station 14+17.5 and 27+98.5 has a grade of +5.25%. What is the difference…

A: Section station - 14+17.5, 27.98.5 Grade - 5.25%

Q: H.W: - A profile of a road where grade elevation starts with (25.00 m) at stat. (12+00) and an…

A: Given data, Station 12+00 13+50 14+00 16+00 Ground elevation (m) 29.20 28.00 25.80 27.40…

Q: What are the Sample Acres when doing 17% cruise using 1/10 ac fixed plots on 89 acres?

A: The values given in the question are as follow Fixed area of plots=89 acres 17% crsise using…

Q: Given the cross section notes of the proposed road to be constructed, find the cross-sectional area.…

A: Base width of road and the side slope is given along with cross section notes and it has been asked…

Q: If A is at station 17+25 and B is at station 43+18, what is the distance between the two points?

A: Distance between two station = STAB-STAA

Q: Q3: Compute the volume using the prismoidal formula and by average end areas for the following…

Q: Determine the adj. length of each path based on the observed data of a closed traverse.

Q: 2. For a proposed new road, the cross sectional areas at different sections are as follows: Station…

Q: :Compute the volume using the prismoidal formula and by average end areas for the following…

A: h = 5.3 ft, h1 = 7.4 ft , h2 = 7.8 ft, b = 24 ft, b1 = 23 ft , b2 = 23.7 ft Let A1 = Area of station…

Q: a new city X under consideration. T

A: This Question is related to Environment and Sanitary Engineering. Here New City X under…

Q: Three level lines established on three different routes to established benchmarks, the result of…

A: Given:- The results of three different routes to established benchmarks are:- Route 1: The elevation…

Q: Three level lines established on three different routes to established benchmarks, the result of…

A: Solution: Given Data: The results of three different routes to established benchmarks are:- Route…

Q: A particular station has the following earthwork cross-section. +2.0 ia +40 +10 If the width of the…

A: Solution; Here, 9.0y 4.5+4.0 +2.0 4.5+2.0 x+1.0

Q: 3. Compute for corrected distances and bearings using transit rule

Q: 10. Towns A and B are on opposite sides of a river. The towns are to be connected with a bridge cD ,…

A: Two towns A and B on the opposite sides of a river are to be connected with a bridge CD…

Q: 1)To compute the average-end area volume, you need to know the distance (L)between the stations of…

A: The average end area method is used to calculate the volume between two cross-sections i.e., two…

Q: Q3. In constructing a new road, the design estimates the following areas of cut and fill for carth…

Q: Situation 3: Problem-solving From the following closed travers. Lines Bearings Distances А-В 120.20…

Q: what are the steps involved in the procedure for locating highway?

A: Factors Controlling Alignment The various factors which control the highway alignment, in general,…

Q: ACTIVITY PROBLEM - The following are section notes of a five-level section Station 1+ 125 ? 12.0…

Q: The following cross section notes are for a road passing a hilly country. The roadbed is 10 meters…

A: step 1: plotting cross section of both stations

Q: TRAFFIC ASSIGNMENT Determine the minimum path for nodes 1, 3, and 9 in below. Sketch the final…

Q: • If a road rises 200 feet over 2 miles of run, what is its grade (or "slope")? • If a hill has a…

Question

Given the following end-sections of a 15-m wide road whose side slope is 1.5:1.
5
8
4
4 + 580
4 + 450
Cross-sectional area at mid-station is equal to
Select the correct response:
180.61 sq.m
147.39 sq.m
150.65 sq.m
118.66 sq.m
CO

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the following data on the table. Fill up the needed data. Balance the traverse by transit rule. Solve the area by DPD or DMD. Sketch the traverse. All values must be in decimal places.
Work out the following problems regarding points andstations along a profile-level route.A. A turning point along with a profile level route measures126.44m beyond station 8 + 24.50. Determine the stationing ofthis turning point.B. For the illustrated problem given above, determine thestationing of the turning point if it is instead located 83.45mbefore the given reference station.C. Determine the distance between station 33 + 45.02 and station 26 + 62.75.
1. A traverse line was measured in three sections: 295.85 m at slope 8045’, 149.58 m at slope 4029’ and 373.48 m. at slope 4025’. Determine the horizontal length of the line.
If A is at station 17+25 and B is at station 43+18, what is the distance between the two points?
Given the following level section notes for stations 1+120 and 1+160: 1+120 | 6.6 | 0 | 7.6 | 0.8 | 3.7 | 1.3 1+160 | 74 | 0 | 98 | 1.2 | 2.3 | 2.4 The side slope is 2:1. The radius of curvature is 275 m. The center of curvature is on the right. a) What is the roadbed width? b) What is the area of section 1+120? c) What is the area of section 1+160? d) What is the volume between section 1+120 and 1+160 using end area method? e) What is the prismoidal volume correction? g) What is the centroid of excess of section 1+160? h) What is the correction due to horizontal curvature?
A and B are two points located on each bank of a river and near abutments of a proposed bridge. To determine its distance, a baseline CD 180m long was established on one bank of the river and the transit was set up at stations C and D and the azimuth were taken as follows: Line Azimuth C-D 210°00'; C-A 260°00'; C-B 290°00'; D-A 301 °00'; D-B 315°00' a. Find the distance AD. b. Find the distance BD. c. Find the distance AB.
The cross section notes of a ground surface at sta 1+200 of a road survey shows that theground is sloping upward to the right at a 10% grade. The elevation of the ground along thecenter line of the proposed road at this station is 150 m and that of the finished subgrade is152, width of the subgrade is 7.00 m with sidelopes of 1.5:1. Compute the elevation at theslopestakes.
Calculate the area of a piece of property bounded by a traverse and circular arc with the following coordinates in feet at angle points: A (526.68, 823.98), B (535.17, 745.61), C (745.17, 745.61), D (745.17, 845.61), E (546.62, 846.14) with a circular arc of radius 25 ft starting at E, tangent to DE, and ending at A.
Express your answer in 2 decimal places. • Determine the length of CD in meters. • Determine the DMD of line CD. Determine the area of the traverse in acres.
Given the technical description of a triangular lot. We are to cut a 190 000 m2 along the side BC starting from B to point D on side CA. 1. Find the length of CD. a. 621.42 b. 690.42 c. 490.09 d. 541.71 2. Find the length of the dividing line BD. a. 825.42 b. 714.68 c. 695.14 d. 794.24 3.Find the bearing of the dividing line from B. a. N 83deg 12’ E b. S 78deg 58’ E c. S 69deg 42’ E d. N 82deg 10’ E
Town A and B are on the opposite sides of a river .The towns are to be connected with a bridge CD perpendicular to the river ,so that the distance AC+CD+DB is as small as possible .Where should the bridge be located?
A pentagonal lot has the following data. SIDE AZIMUTH DISTANCE(M) AB 198° 30' 108.20 BC 288° 98.60 CD 356° 30' 112.40 DE 42° 20' 120.00 EA ? ? Find the following: a) bearing and distance (m) of line EA b) area of the lot ( in m2 ) and (in hectare) c) DMD (Double Meridian Distance) of line BC d) DPD (Doubel Parallel Distance) of line DE Kindly show a full and detailed solution, thank you!