A simply supported beam is subjected to a linearly varying distributed load q(x) = 9, with maximum intensity qo at B. The beamhas a length L = 4 m and rectangular cross section with a width of 225 mm and height of 270 mm.90q(x)В-L-Determine the maximum permissible value for the maximum intensity, 9o. (in kN/m) if the allowable normal stresses in tension andcompression are 131 MPa.kN/m

Answered: Image /qna-images/answer/871e6319-3928-43a2-a615-c8e8c2b47d45.jpg

Answered: gth L = 4 m and rectangular cross…

Engineering

Civil Engineering

gth L = 4 m and rectangular cross section with a width of 90 9(x) B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A couple M of moment 8 kN·m acting in a vertical plane is applied to a W200 * 19.3 rolled-steel beam as shown. Determine (a) the angle that the neutral axis forms with the horizontal plane, (b) the maxi-mum stress in the beam
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
consider the 20m beam shown • what is the location of the absolute maximum moment from the center of the beam? answer in m •what is the maximum moment when the middle load is positioned at the center of the beam? answer in kN-m
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 16 cm as width, 23 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
The simple beam with overhang carries a uniform load, w=10kN/m and force P=20.38kN. a. determine the maximum bending stresses (T & C) and absolute maximum transverse shear stress b. check if the beam is safe if the allowable bending stress (T & C) = 120 MPa and the allowable shear stress=80MPa
f. What is the moment of inertia (I) about the neutral axis of the section? (in in^4) g. What is the first moment of an area (Q) about the neutral axis of the section? (in in^3) h. What is the maximum shearing stress (fv) of the beam? (in psi) i. What is the maximum flexural stress (fb) of the beam? (in psi)
Solve for shear force at 10 meters from A
Beam ABC with an overhang BC is subjectedto a linearly varying distributed load on spanAB with peak intensity q0 = 2500 N/m and a pointload P = 1250 N applied at C. The beam has a widthb =100 mm and depth h = 200 mm. Find the state ofplane stress at point D located 150 mm below the top ofthe beam and 0.2 m to the left of point B. Also find theprincipal stresses at D. Neglect the weight of the beam.
The wide-flange beam is subjected to the loading shown in (Figure 1). Suppose that P = 40 kN. Follow the sign convention. a) Although it is not very accurate, use the shear formula to determine the shear stress developed at point A b) Determine the principal stress σ1 at point A c) Determine the principal stress σ2 at point A
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
From the given simply supported beam below, determine the following: d. The moment of inertia with respect to the neutral axis. e. The maximum flexural stress and shear stress of the beam. f. The bending stress at point B and C. g. The shear stress at the mid-point of the beam.
A simple beam with a W 10 × 30 wide-flangecross section supports a uniform load of intensityq = 3.0 kips/ft on a span of length L = 12 ft (see figure).The dimensions of the cross section are h =10.5 in.,b = 5.81 in., tf = 0.510 in., and tw =0.300 in.(a) Calculate the maximum shear stress τmax oncross section A–A located at distance d = 2.5 ftfrom the end of the beam.(b) Calculate the shear stress τ at point B on thecross section. Point B is located at a distancea =1.5 in. from the edge of the lower flange.