NOTE: PLEASE INCLUDE AT LEAST 3 DECIMAL PLACES The length of rod AB is 10 m and it is supported at midspan by linkCD. The length of line AC is 4 m long. The 25 kN load is located at the midspan ofsegment AD.*The support at Point A is pin – connected*Determine the following:a.) The Reaction at Point A.b.) The Reaction of the Link support CD.25kN10kN3 kNmAВC

tanθ = 54⇒ θ = tan-154= 51.34°

Answered: gth of line AC is 4 m long. The rt at…

Engineering

Civil Engineering

gth of line AC is 4 m long. The rt at Point A is pin - connected* he following: etion at Point A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: example: FBD Va- (EF) M- (IM). X- value 200 lb/ft BMATHalino.com 2 ft R = 900 lb |A H| 4 ft 2 ft Loa...

Q: Consider a standard flexural strength specimen of length L, width a, and depth a. Assume center poin...

Q: Extrusive igneous rocks: in this type of igneous rocks the magma solidifies at * .the surface True F...

A: Igneous rocks are of two types Intrusive igneous rock. Extrusive igneous rock.

Q: Determine the standard deviation for the replicate determination of the Hg in soil: 0.356 ppm, 0.228...

Q: b=480mm d=700mm fc'=30MPA fy=400MPA Mu=1430kN-m Determine As A. USE NSCP 2015, As = sq.mm. B. USE NS...

Q: A line between stations P and Q laid on a slope of 1 in 5 was measured as 350 m using a 50 m tape. T...

Q: Activity Predecessor A B A C B.C E D n the table above, what is the free float of Activity B

Q: o. A rectangular sedimentation tank following coagulation- Exa flocculation is to treat a flow of 30...

Q: 3. 8 KN/m TI|||||||I. - 9 m- 3 m 20 kN 3 m Assume A is fixed and Cisa rocker Bis a rigid joint. Find...

Q: For the given section below, Compute the maximum stress of concrete and steel. All dimensions are in...

Q: Problem 2 If atmospheric pressure is 95.7 kPa and the gage attached to the tank reads 188 mmHg vacuu...

Q: Problem 4 The figure shown shows a setup with a vessel containing a plunger and a cylinder. What for...

Q: Make a CONCRETE chain and make sure it is understable.

Q: Find the safest value of load "P" for the beam loaded shown. fc'=35MPA, Use GRADE 420 steel bar and ...

Q: . What factors you consider in selecting a site for a rain-gauge station? 2. Distinguish between re...

Q: Solve

A: Prestressing is a method in which intital compressive stresses are induced in concrete before loadin...

Q: *Prob. 2.3-9. A “rigid" beam AD is supported by a smooth pin at D and by vertical rods attached to t...

A: We have to determine the value of the beam angle theta that corresponds to the strain and the corres...

Q: Find the pressure @ m in psi when fluid A is water and fluid B is carbon tetrachloride (1.60). z = 2...

Q: y = kx2 b a -a-

Q: Two rigid bars are connected with a rotationalspring, as shown in the figure. Assumethat the elastic...

A: Given:- L=6fth βR = 75 kip-in./rad To find:- Pcr

Q: Determine the safe wall thickness

A: PRESSURE VESSELS:

Q: H.W The uniform thin pole has a weight of 50 N and a length of 26m. If it is placed against the roug...

A: Given:- The weight of the uniform thin pole = 50 N The length of the pole = 26 m The distance betwe...

Q: 1 The tolerance, tol, of the solution in the bisection method is given by tol = (b,-4.), where a, an...

Q: 7. If the friction is neglected, then, a) Vr1 > Vr2 b) Vr1 < Vr2

A: To find: If friction will be neglected then what will happen

Q: The stress field in a loaded aluminum plate was determined as [-2x² + 3y² 3x + y+ 5] O = F[3x + y+5 ...

Q: 1. By the Area Method, determine the quantity of cement, sand and gravel of the proposed concrete pa...

A: We have to determine the value of quality of the cement sand and gravel of the proposed concrete par...

Q: A 2m 2m

Q: Complete the differential level notes shown below, and determine the d of TP2 and BM11 STA BM 10 2.0...

Q: Design the positive moment of the beam shown below, determine the number of 20mm diameter bars and t...

Q: why do coal tar pitch and asphalt not compatible? why do we need to avoid these two to contact each ...

A: coal tar : tar produced by distilling bituminous coal and used mostly as an industrial fuel, in the ...

Q: 3. The force analysis on a curved vane is understood using.

A: Curved vanes are part of turbines on which water falls . These curved vane rotates about their axis ...

Q: Problem 3. Find the manometer reading in the lossless system shown. Ans h=11u ft eft Water 25t Mercu...

A: To Determine Manometer reading in the lossless system.

Q: 80 kN 10 kN/m A C B 2 m RA 8 m Re

A: Given data:

Q: A fuel oil tank is an upright cylinder, buried so that its circular top is 14 feet beneath ground le...

A: We know that work =Force * Displacement

Q: Q1- a- Calculate the horizontal and vertical reactions at fixed supports A and H. b- Calculate the b...

A: Solution: As for the given schematics the moment diagram will be

Q: What is the period of this sine-function?

A: periodic function:

Q: What are the uses of Hot Bitumen Built-Up Roof Membrane?

A: Built-up roof material consists of bitumen-saturated felt, coated felt, polyester felt, or other fab...

Q: A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end...

A: Given:- P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi an...

Q: weir that will increase the

Q: Plot the load-def lection diagram for apinned-end column with eccentric axial loads (seefigure) if t...

A: Given:- L = 3.6 m, I = 9.0 x106 mm4, E = 210 GPa. To find:- the load-def lection diagram

Q: Solve the following problems using method of joint and section. 1. A Fink roof truss is loaded as sh...

A: We have to determine the value of force in member DF, FE, and EG as per method of joint and section....

Q: d 1.59 m d = 5.22 feet Problem 8-12 0-mm-diameter concrete pipe is laid on a slope of 1 m per 500 m ...

A: To Determine From where sinθ is taken from, in the solution given.

Q: A 30 cm x 70 cm rectangular ring beam curved in plan is supported on 8 columns located equidistant o...

Q: 30 kN 50 kN to B D A 1m 3 m 2 m Figure P-403

Q: 10. Given the diagrams in Figure P5.1 of progress on individual work pack- ages of a project, answer...

A: Given Data : BCWS = budget cost of work scheduled (planned value) ACWP = Actual Cost of Work Perfor...

Q: ng of 3 m diameter is constructed at a depth of 2 m below the ground su n is subjected to a load of ...

Q: Vehicles arrive at a toll booth with a mean arrival rate of 2 veh/min (the time between arrivals is ...

Q: 1' 50 Ib 50 Ib

A: Step 1: From the diagram, Diagonal value = √(12+12)=√2 ft Resolving the forces horizontally and vert...

Q: The azimuths of the back and forward tangents (measured from North) of a simpl curve respectively ar...

Q: In the figure shown, what is the static pressure in kPa in the air chamber? AIR 2.0 m OIL S-0.80 4.0...

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

NOTE: PLEASE INCLUDE AT LEAST 3 DECIMAL PLACES

The length of rod AB is 10 m and it is supported at midspan by link
CD. The length of line AC is 4 m long. The 25 kN load is located at the midspan of
segment AD.
*The support at Point A is pin – connected*
Determine the following:
a.) The Reaction at Point A.
b.) The Reaction of the Link support CD.
25kN
10kN
3 kNm
A
В
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The ABC rigid bar is suspended by the BD rigid bar and by an A pin that connects it to the other ADE rigid bar. If the overhang load at point C is equal to 12kN, calculate the force on the BD bar and the reactions FA = √??2 + ??2, on pin A and the reaction FE roller located at point E. Disregard the weights of all the bars.
Determine the reactions at the fixed support at A and the roller at B. Support B settles 5 mm. Take E = 200 GPa and I = 300(106) mm4.
Solve for the reactions at thesupports.Roller support to F1 has a distance of10ft. F1 to F2 has a distance of 10ft and F2 topin support has a distance of 10ft. F1= 350lbF2= 400lbθ=30°
Solve for the reactions at both supports. P=8.17KN
a. Determine the degree of indeterminacyb. Select vertical reactions at C and E as redundants. Draw the primary beam by removing the rollers at C and Ec. Subject the primary beam to external loads of 120 KN at B and at D. Compute for C and E using Virtual Load Methodd. Subject the primary beam to unit values of redundants Cy and Ey. Compute the flexibility coefficients fCC, fCE, fEC, fEEe. Write the compatibility equationsf. Solve for the reactions at supportsg. Draw Shear and Moment Diagrams
From the loaded frame of a vertical member is 6m and horizontal member is 5m and 10kN located at midspan determined the reaction at roller support, and reaction at hunge support
(a) Assuming that no loads act in Figure P9.16,compute the reactions if support B is constructed 0.48 in.too low. Given: E = 29,000 kips/in.2, I = 300 in.4. (b) Ifsupport B settles _32 in. under the applied loads, computethe reactions.
For the frame shown,a) Solve for the reaction at the rollersupport at A and the horizontaland vertical components of thehinge at D.b) Solve for the horizontal andvertical components of thehinge force at B as it acts onmember ABC.c) What is the tension in the cordAE?
The bent rod ACDB is supported by a sleeve at A and a ball-and-socket joint at B. Determine the components of the reactions and the tension in the cable. Neglect the mass of the rod and any moment reactions at A. 1) Find all A reactions: Ay=? Ax=? 2) Find all B reactions: Bx=? By=? Bz=? 3) Find the tension force: T=?
Determine the reaction (in kN) of the central support of the beam shown in the figure. Q=35.5kN/m and L=5m
Beam ABC is loaded as shown. Support C settles 10 mm after the load is applied. taking E = 200GPa and I = 300x10^6 mm4. Removing the support at B, what would be the vertical displacement at B of the primary structure in kNm3/EI, Find the Reaction at support B in kN and Determine the Linear flexibility coefficient taken at B, fBB, in kNm^3/EI.Single choice.
In the structure of the figure q0= 1000 [N / m], P= 100 [N], a=1[m], b=3 [m], c= 2 [m] and θ= 30̊. Consider that the charges P act at the midpoint of their respective spans. a) Calculate the reactions at A and D b) Calculate and graph the normal (N), shear (V), and moment (M) reaction diagrams in the sections AB, BC, and CD. c) Determine (if applicable) at which points on the beam the lowest shear values V(x) y are reached moment M(x). Also indicate the values of these variables at these points. d) Determine (if applicable) at which points on the beam the maximum cut-off value V(x) is reached and moment M(x). Also indicate the values of these variables at these points.