How Design an idealized class B output stage to deliver an average of 25w to an 852 speaker, the Peak ont Put Valtage must be no larger than 80 Percent of supply voltages Vcc. Determine @ vcc 2 the Peak Current in each transistor the average Power dissipall in each transistor the Power Conversion efficiency. Ans: vcc = /25v| 2 @ ILp) = (2-5A] ® PB =[7.46| + 12 = 162.8%

How Design an idealized class B output stage to deliver an average of 25w to an 852 speaker, the Peak ont Put Valtage must be no larger than 80 Percent of supply voltages Vcc. Determine @ vcc 2 the Peak Current in each transistor the average Power dissipall in each transistor the Power Conversion efficiency. Ans: vcc = /25v| 2 @ ILp) = (2-5A] ® PB =[7.46| + 12 = 162.8%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the MOSFET amplifer circuit shown in Figure below. Assume µnCox(W/L) = 4mA/V2, Vt = 1V Draw an equivalent DC model, and equivalent circuit of the amplifier. Determine the drain current and its overall voltage gain respectively.
For the 2 circuits shown above, βnpn = 100, βpnp = 50, VDO = 0.7 V, R2 = 150 kΩ, and RB = 12 kΩ Using the ac small-scale signal analysis, determine for each circuit: a) The voltage gain (Av = vout/vin) b) The input resistance (Rin) c) The output resistance (Rout)
A base voltage of four volts is applied to an NPN bipolar junction transistor. A twenty kilo ohm resistor is linked to the base, while a hundred kilo ohm resistor is connected to the collector. The Collector is powered by a six volt supply voltage. Assume the transistor is in active mode, with a fifty common Emitter current gain(β).(i) Utilize the dc equivalent model of the transistor to draw the circuit design.(ii) Calculate the Collector current (IC) and the Base current (IB) .ii) Locate/determine the result (VCE).
Refer to the differential amplifier circuit shown below . Determine the quiescent DC voltage at the collector terminal of each transistor assuming VBE of two transistor are negligible. What will be the quiescent DC values if VBE is taken to be 0.7 V.
A Darlington pair of transistors is connected asshown in Figure P10.39. The transistor parameters forlarge-signal operation are Q1: β = 130; Q2: β = 70.Calculate the overall current gain.
What are the phenomena observed in integrated operational amplifiers?
What is the output voltage vO if theop-amp is ideal? What are the values of the baseand emitter currents and the total current suppliedby the 15-V source? Assume βF = 40. What is theop-amp output voltage?
What is common mode voltage in amplifier explain simply?
In the circuit given in the figure, Vcc = 15V, R1 = R2 = 10k ohm, RE = 1k ohm, RL = 0.5k ohm and transistor parameters are given as VBE = 0.7V, beta (dc) = beta (0) = 100. According to this;a) Calculate the values of DC bias currents and voltages (I (BQ), I (CQ), V (CEQ)).b) Using the hybrid model of the transistor, draw the small signal equivalent circuit of the circuit.c) Derive the input impedance expression of the circuit and calculate its value.d) Derive the voltage gain expressions A (vi) and A (VG) and calculate its value.e) Derive the current gain expression A (i) = I (0) / I (i) and calculate its value. I sent you question's image. Thank you..
Explain the transistor amplification action with drawing figure and examples
An NPN silicon transistor having a nominal ß of 100 is to be used in a CE configuration with Vcc= 15 V. The Q point is to be Ic = 4mA and VcE = 12V . Now design the circuit diagram.
a.) Consider a two-BJT configuration in Figure 1. You may assume that both transistors are the same with the same β, VBE,on = 0.7 V, and VCE,EOS = 0.3 V. Determine the minimum voltage VBE that will turn ON both Q1 and Q2. b.) Using the BJT small-signal model given in Figure 2, determine the AC current gain Ai = iout/iin for the circuit given in Figure 3. Assume ro >> rπ. You may assume that β is large.