hand written plz Horizontal Curve data STAPI= 98+47.30 R = 1000.00 A=19° 20'00" What is the deflection angle to 98+00, set on the BC, back sight the PI? O 3° 52'47" O 10° 00'00" O3° 31' 29" O 7° 02' 58" O 05° 20'00"

hand written plz Horizontal Curve data STAPI= 98+47.30 R = 1000.00 A=19° 20'00" What is the deflection angle to 98+00, set on the BC, back sight the PI? O 3° 52'47" O 10° 00'00" O3° 31' 29" O 7° 02' 58" O 05° 20'00"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The thrust, F (MLT-2), generated by a ship's propeller is generally thought to be a function of the…

Q: The beam ABC is to be loaded with a 300 lb/ft uniform distributed live load so it causes the largest…

Q: Q4: The bearings and lengths of straights R1-X1 and X1-R4 taken from Table below, are as follows:…

Q: ortions of the rod ABC are made of an aluminum for which E = 69GPa. Knowing that the magnitude of Q…

A: For zero defelction :δAB=δBC

Q: 2 kN/m₂ F 2m +3m 6 kN/m V

Q: ▪ A roadway is determined to have 400 18-kip single axles, 200 24-kip single axles, and 100 40- kip…

A: PSI = 4.5%So= 0.4TSI = 2.5R = 99%Single Axle load = 400 18-kiptandom Axle load = 200 24-kiptriple…

Q: For a catchment in UP, India, the mean monthly temperatures are given. Estimate the runoff and…

A: Estimation of runoff is done by following formula as per khosla method: Rm=Pm-Lm Pm = monthly…

Q: Q3: In venture meter, the volume water through 10 second is 500ml.the total head of water for points…

A: Given :

Q: Evaluate or simplify the following expressions: (a) 8 x (b) ở $ (c) 8,8 kk ijij jk (d) &1jk 83j Vk

Q: f P8-4. Determine the force P needed to cause impending motion of the block. 2m W = 200 N 1 m…

Q: A ladder 6-m long leans against a vertical wall with the lower end on a level floor. The upper end…

Q: Q.1) Answer one only A) A rectangular plot (ABCD) forms the plane of a pit excavated for road work.…

Q: M N M X 8 mm N 8 mm t 50 mm 8 mm 50 mm

Q: Determine the largest weight W (

A: This question has been taken from Engineering Mechanics

Q: Q2 / Abuilding to be constructed on a hill with foundation elavation = 30m. the areas bounded by…

A: The given data is shown below:

Q: Compute the maximum deflection for the cantilever beam loaded as shown. Assume E=200GPa and I=120 x…

Q: The photic zone of the ocean is also known as the sunlight layer. It is the region in which phyto-…

A: Many factors affect light emission in bioluminescence imaging (BLI), which is why creating a kinetic…

Q: For the beam and loading shown determine (a) the equation of the elastic curve, (b) the deflection…

Q: A rural township in central Arkansas has recently replaced several septic tanks that have an…

Q: 2/58 The cantilevered W530 x 150 beam shown is subjec- ted to an 8-kN force F applied by means of a…

Q: Problem #4 G F B X KN 3+B m Determine the following: 18. Horizontal reaction at G. (kN) 19. Bar…

A: Given data x = 137 y = 37 a = 6 b = 8 c = 1 T = Tension in member C = compression in member

Q: Problem #5 y-axis 100+ Y (mm) Y mm x-axis 250 + A (mm) 25. Determine the centroidal moment of…

Q: Determine the moment of each force about the bolt located at A (Figure 1). Take FB = 45 lb. Fc = 30…

A: This question is from mechanics Value of FB is equal to 45lb Value of FC is equal to 30 LB We have…

Q: Convert the given polar complex number, 3212° into the form a + jb, giving your answer correct to…

Q: The extra widening required for a two-lane national highway at a horizontal curve of 275 m radius,…

A: given design speed V=80 kmphRadius of curveR=275 mradius of wheel base L=7.5 m

Q: S. A well of diameter 20 cm fully penetrates a confined aquifer. After a long period of pumping at…

Q: Compression. HÅ Value BE ? Units Request Answer the force in members CJ of the truss, and state if…

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

Q: Problem-2 In an SPT test gave the average below count of 35 in fine sand below water table. Find the…

A: given average below count for SPT testN'=35it is needed to find the corrected value of SPT number.

Q: Design the most economical section for a single span beam which carries a uniform load of 10 kN/m…

A: Solution: Given: UDL = 10 kN/m Point load = 200 kN L = 4 m ASD: Wu = 10 kN/m PU = 200 kN Moment at…

Q: 4. A settling chamber is to be 2 m wide, 7 m high, 13 m long and has 10 trays, including the bottom…

A: Given, L = 13 m B = 2 m H = 7 m n = 10

Q: distilled water density ρH2O. t [°C] ρH2O [g/cm3] 15 0.99996 16 0.99994 17…

Q: 5. A plate of 6inx 1 in with steel grade A36 (fy-36ksi and Fu-58 ksi) is used as tension member with…

Q: 2. Determine the slope and deflection at point A for figure (a) and point D for figure (b) as shown.…

A: since questions are long and i have explained in great detail so it takes time to solve one…

Q: At a temperature of 29.8 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time…

Q: Explain the following statement: The LBSR project was a self-certified project.

A: By permitting a certified expert to take accountability for and validate a project's conformity with…

Q: Small wheels have been attached to th B and roll freely along the surfaces show hat wheel A moves to…

A: Draw the free body diagram- Write the relationship between the velocities. VB =VA+VBAUsing…

Q: Question- Metal body floats at the interface of water and oil of SG=0.85 such that 35% of its volume…

A: given- Metal body-Specific gravity of oil SG=0.8535% submerged in water65% submerged in oil

Q: A cylinder 100 in diameter and weighing 500 N has impending motion counterclockwise due to an…

A: Given values, weight of cylinder w = 500 N diameter, d= 100 in.=(100*2.54)/100 = 2.54 m Torque, T =…

Q: 5. Using the derived equation from the previous question, solve the following problem: A race car is…

A: Given, r = 55 m θ = 40o S = 216 km/hr or 60 m/s

Q: compute the force acting on the flange.

Q: An confined aquifer has a thickness of 30m. a fully penetrating 20cm diameter well in this aquifer…

A: Q=πkh22-h12lnr2r1Q=35 litsec=35×10-3 m3sec35×10-3=π×k×29.52-22.52ln10010k=7.0475×10-5 msec Hydraulic…

Q: Q.1 The velocity distribution in a turbulent boundary layer is given by 1/7 What is the displacement…

Q: ▪ A roadway is determined to have 400 18-kip single axles, 200 24-kip single axles, and 100 40- kip…

Q: If the overall efficiency of a Pelton Turbine is 65% and its Mechanical efficiency is 80%, then its…

A: given- overall effciency ηo=65%mechanical effciency ηm=80%

Q: In an old survey performed in 1965, a line AB had a magnetic bearing of S75deg10’W when the magnetic…

A: Given Data:Magnetic Bearing = S75°10'WMagnetic declination = 4°30'Change in Magnetic declination =…

Q: . Calculate the force exerted by the wall to the ladder?

Q: Wu-100 kN/m 6 m D www. Question 9 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate…

A: Neutral Axis: The axis which passes through the cross-section of the beam or a shaft that represents…

Q: The following data were obtained by stadia observation: vertical angle, +12deg 30 min; upper stadia…

Q: Problem III. Solve the problem using Conjugate Beam Method. From the given fixed beam at both ends,…

A: Given data:- Below diagram is given;

Concept explainers

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.

Question

hand written plz
Horizontal Curve data
STAPI = 98+47.30 R = 1000.00 A=19° 20'00"
What is the deflection angle to 98+00, set on the BC, back sight the Pl?
O 3° 52'47"
O 10° 00'00"
O3° 31' 29"
O 7° 02' 58"
O 05° 20'00"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the following: a. Bearing AB b. Deflection angle CB c. Azimuth from the north of DE
1. A triangular piece of land ABC (clockwise) has the following directions in azimuth fom South. AB = 225o23’, BC = 325o20’, CA = 100o10’ Compute the interior angles. 2. An open traverse ABCDE has following azimuth from South: AB = 250o30’ BC = 280o20’ CD= 210o45’ DE = 150o50’ Required: Deflection angles at points B,C, and D. Draw the figure properly.
Convert the following bearings to equivalent azimuth: a. AB, N 25°25' W b. BC, due East
Convert and illustrate the following bearings into equivalent azimuths: a)AB N70°50’W b) BC S228°25’W c) CD N135°17’E d) DE S120°29’E e) EF Due West
prove the formula of the combined correction for earths curvature and refraction Hcr = 0.0675 D^2 where: Hcr= combined correction D = horizontal distance
The interior angles of a five side traverse are as follows: A=117°30' B=96°32' C= 142°54' and D=132°18' . The angle E is not measured. Sketch to Calculate the following: a. Deflection angle at E. b. Azimuth of the line AB.
Closed traverse ABCD has the following bearings: AB = N 45°20′ E; BC = S 47°32′ E; CD = S 14°55′W; DA =N68°00′W Compute the interior angles and provide a geometric check for your work. Find the following interior angles A, B, C, D
In the figure shown, compute the following A. Bearings of BC, and FE B. Azimuth of CD, and AF C. True Azimuth of AF, and DE if the magnetic declination is 3°27’20”
An 80 m spiral is used to connect a 4o simple at both ends. 1. Compute the long tangent. a. 53.37 m b. 42.51 m c. 26.73 m d. 36.41 m 2. Compute the deflection angle at second quarter. a. 2 deg b. 0.67 deg c. 1.33 deg d. 0.33 deg 3. Compute the tangent distance if I = 50deg. a. 261.51 m b. 185.62 m c. 128.14 m d. 174.02 m
Your team want to measure line AB but there is an obstruction on line. You set up two lines AC and CB 2350.700 m and 1285.350 m, respectively. Point C was set at a perpendicular distance of 270 m from point D. Point D is on line AB. Using slope correction formula for less than 20% slopes, determine the length of line AD. the length line BD the length of line AB.
The following data were obtained by a stadia measurement; vertical angle is 30deg23mins, and observed stadia intercept is 2.20m. The stadia interval factor at the measurement used 95.50m and C is 0.30m, if the height of the instrument is 1.62m, and the rod reading is taken 1.95m. Determine the D, V, S and the Difference in elevation. (D= distance, V= Vertical Distance, S= Sight distance) Topic: Tacheometric Surveying Pls answer in COMPLETE solution. DIAGRAM/ILLUSTRATION of the solution is a must, for better understanding. 3 dec places all answers. THANK YOU.
to find out the included angles in a closed survey PQRSTP, the following observations were made with the compass. calculate the included angles after correcting the local attractions line fore bearing(FB) back bearing(BB) PQ N 620 45/E S 62015/W QR N 210 00/W S 200 45/E RS N 710 30/W S 710 30/E ST S 390 00/W N 380 00/E TP S 540 30/E N 530 15/E