hand written plz i'll upvote Shown in the figures (1) and (2) are trusses containing members that are made of same materials (Modulus of Elasticity E) and with same cross-sectional area A. When the load P is applied, which of the following statement about the strain energy of the entire system is CORRECT? Strain energy U(1) > U(2) Strain energy U(1) < U(2) Strain energy U(1) = U(2) O Impossible to determine B 18 30° D (1) ic B 30° D (2) ic

hand written plz i'll upvote Shown in the figures (1) and (2) are trusses containing members that are made of same materials (Modulus of Elasticity E) and with same cross-sectional area A. When the load P is applied, which of the following statement about the strain energy of the entire system is CORRECT? Strain energy U(1) > U(2) Strain energy U(1) < U(2) Strain energy U(1) = U(2) O Impossible to determine B 18 30° D (1) ic B 30° D (2) ic

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.13P: A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean...

See similar textbooks

Similar questions

Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
A material is subjected to a general state of planestress. Express the strain energy density in terms of theelastic constants E, G, and n and the stress components sx,sy, and txy.
If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3 respectively, What is the axial strain in the cylinder wall at mid-depth?
The diameter (d) of a solid rod (i.e., with a circular cross-section) is 16 mm and ismade from a homogeneous material. The length (L) of the rod is 1.75 m andYoung’s Modulus for the material (E) is 250 GPa. When the rod is placed undertension it experiences deformation and a stress (?) of 650 MPa. Calculate thefollowing:(i) Strain energy (U) to 2 decimal places in Joules.(ii) Strain energy per unit volume (U/V) in J/m3.(iii) The change in length ∆L to 2 decimal places in mm.(iv) The strain (?) due to deformation to 2 significant figures
The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elasticrecovery and the increase in the gage length after it is unloaded.
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod is 10 mm and 120 mm, respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0.0053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Calculate : A) Strain in the steel rod B) Load carried by the steel and the brass rods C) Modulus of elasticity for the brass. Can you please resend that question as it appears to be blank??
If Poisson's ratio of a material is 0.5, then the elastic modulus for the material is a)three times its shear modulus b)four times its shear modulus c)equal to its shear modulus d)indeterminate
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass