The simple beam with a height of 200mm, a width of 100mm and a length of 4m is loaded as shown. Do the following and provide a free body diagram in solving. 7. Determine the shear stress at a section 3m from the left end;8. Determine the deflection at 2m from the left end.9. Determine the slope at A.10. Draw the elastic curve. 7.5 KMtin tinim2 kN/m[

Answered: Image /qna-images/answer/29ef373f-07f0-4618-a128-3c054d32aa0a.jpg

Answered: height | bartleby

Engineering

Civil Engineering

height

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 5.19 Vertical reaction developed at B in the frame below due to the applied load of 100 kN (with…

A: Given data in question Load Dimensions MOI Internal hinge To find out Vertical reaction at B

Q: Determine the maximum axial force P that can be applied so as not to exceed an allowable tensile…

A: Given :

Q: The rigid beam ABC is supported by three identical cables. The beam was initially horizontal prior…

A: Given :

Q: Draw the shear force (S.F) and banding moment (B.M) diagrams for the beam and loading shown in…

A: Need to draw shear force and bending moment diagram

Q: Water is flowing at a depth of 1.3 m and velocity of 0.95 m/s when controlled by a sluice gate at a…

A: Sluice Gate : A sluice gate is provided to control the sluice through a valve. Sluice is an…

Q: The moments of inertia of the area A about the parallel p- and p'-axes differ by 69 in.4 Compute the…

Q: 6. • Draw a free body diagram of box W₂. Determine the weight of each box (W₁ and W₂). Determine the…

Q: 6. Referring to Figure 6, compute the maximum force P that can be applied by the machine operator,…

Q: 11-17. Determine the moments at the fixed support A and joint D and then draw the moment diagram for…

A: Given data

Q: 12 F2-10. If the resultant force acting on the bracket is to be 750 N directed along the positive x…

Q: Problem 3.25 The acrylic plastic rod is 200 mm long and 25 mm in diameter. Figure 1 of 1 200 mm Part…

Q: Calculate the moment of inertia of the shaded area about the x-axis. 83 mm 83 mm 42 mm Answer: Ix =…

Q: A 2m W₁ * V * * * * * B 5m 2m P₁ P₂ V V D 5 F 1m 1m tt W2 3m G 1m

Q: height of the centre of gravity of the car above the road

Q: Axial Force, Shear and Moment Diagram of Frames Draw completely the AF-d, V-d, & M-d of the…

A: Given A frame Required Axial force, shear force and bending moment diagram

Q: Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of shaft…

A: Given Head = 45 m Flow rate = 0.03 m3/s Shaft power = 20 kW

Q: The two shafts are made of A992 steel. Each has a diameter of 0.9 in., and they are supported by…

A: Given :

Q: STRUCTURAL MEMBERS SLAB B (m) 8 8 5.3 4.5 4 Slab 1 Slab 2 Slab 3 Slab 4 Slab 5 BEAMS Grid A Grid B…

Q: Two blocks A and B of the same mass 1.11 kg are released from rest on a 28° incline when they are S…

Q: A circular tank of 3.91m in diameter is uniformly loaded with 100 kPa. Compute: a) The stresses…

A: Given:- The diameter of the circular tank =3.91 m The magnitude of the load = 100 kPa To…

Q: SITUATION 3: A soil sample was determined in the laboratory to have a liquid limit of 41% and a…

Q: Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if…

Q: A singly R.C. beam has powerful section 300 x 450 mm, furnished with 3-18 at effective cover of…

Q: Draw the shear and moment diagram for the beam shown in problem 3. 1k/ft 6ft + 4 ft 3k 4 ft

Q: In the beam shown, taking W1 = 3 kN/m, P1 = 7 kN, P2 = 4 kN, and W2 = 7 kN/m. c) Determine the shear…

Q: Which type of internal bending moment causes the following bending stresses? Y Tancion

A: Under positive Bending moment M is positive Using equation σtensionCompression=MyI

Q: Problem 1) Apply the force method to determine the reactions at the supports. Assume C is fixed and…

Q: Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch…

A: Given,P=8650 lbsb=2.5 int=0.75 inr=14 in=0.25 inσmax=7670 psi

Q: Design a most economical spiral-column cross-section to support factored forces and end moments of…

Q: order to eliminate the sag and temperature correction, given the following? a = 6x10^-6 m^2 E =…

A: Temperature correction :CT=Tm-ToLαCT=20-22300.0000116=0.696mm

Q: Define and explain the difference between resolved shear stress (τR) and critical resolved shear…

A: The tensile stresses or compressive stresses applied on a material can be resolved into normal and…

Q: (7)31 =

Q: In the beam shown, taking W1 = 3 kN/m, P1 = 7 kN, P2 = 4 kN, and W2 = 7 kN/m. e) Determine the value…

A: Given data:

Q: The 62-mm-diameter steel shaft is subjected to the torques shown. (Figure 1) Figure 1 of 1 400 mm B…

A: Angle of twist The angular distortion of an item caused by a few twisting torques is known as the…

Q: f the resultant force of the forces system shown in Fig . ( 1 ) is to be ( 700 N ) directed along…

A: Answer: We know that resultant is given by R = ∑Fx2+∑Fy2 ∑Fx = Algebric Sum of Horizontal forces…

Q: A cantilever beam of length L=6 ft supports a uniform load of intensity q = 200 lb/ft and a…

A: Given A beam Required Section modulas and select suitable wide flange beam

Q: essay on HOW to do (1) engineering control (2) administrative control and (3) Personal Protective…

A: (1) Engineering ControlThe precautions to be taken while any engineering activity is underway or…

Q: Determine the moment at point B and point D of the beam

A: Given :

Q: A 450 mm x 550 mm TIED column is reinforced with 12-20 distributed evenly on the two short sides…

A: Interaction Diagram: When the column is subjected to axial load with the uniaxial moment, in order…

Q: Determine the effective soil pressure if the soil bearing capacity is 130 kPa and the top of the…

A: The bearing capacity of soil is defined as the capacity of the soil which will bear the loads or we…

Q: Question -for a traffic Stream speed density relationship was found to be Determine U= 42-46-D-22 K…

Q: SITUATION 5: Specifications for a proposed earth fill require that the soil be compacted to 95% of…

Q: If an airplane is flying at an altitude where the actual pressure is 4.72 x 104 N/m2 respectively,…

Q: If the elastic modulus and the Poisson's ratio of the clay layer are respectively 50 x 10³ kPa and…

Q: compute the reactions for the structures

Q: For the beam and loading shown, determine the reaction (N) at the pin if W = 17243 N/m, V=61716 N/m,…

A: The values and diagram given in the question are as follows: w=17243 N/m V=61716 N/m x=1.53 m y=3.53…

Q: Indian Standard (IS) Light Compaction test is usually conducted in 3 layers in a 1000 cc mould. How…

A: Given- IS Light Compaction Test- 3 layers in 1000 cc mouldfor 2250 cc mould number of blows per…

Q: A centrifuge rotor is accelerated for 30 seconds from rest to 20000 rpm. Through how many…

A: Given It takes to accelerate centrifuge rotor only 30 sec from rest to 20,000 rpm .

Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…

A: Given :

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

The simple beam with a height of 200mm, a width of 100mm and a length of 4m is loaded as shown. Do the following and provide a free body diagram in solving.

7. Determine the shear stress at a section 3m from the left end;
8. Determine the deflection at 2m from the left end.
9. Determine the slope at A.
10. Draw the elastic curve.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 15 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Knowing that L = 4 m, Concentrated load P = 15 kN and uniform distributed load w = 12 kN/m, determine the slope at C by Castigliano’s Theorem.(E= 200 GPa, I = 40x106 mm4)
Determine the moment of Ma at the base of the buttress due to the applied thrust force F. Use Varignon's theorem. Force F is at a 5:12 slope.
Determine the deflection at the free end Ans: kN.m3 Determine the slope at point B. Ans. kN.m2
If mu = 0.30 under both blocks and A weighs 400 lb, find the maximum weight of B that can be started up the incline by applying to A a rightward force P of 500 lb.
3. The body on the incline is subjected to the vertical and horizontal forces shown. Find the components of each force along X-Y axes oriented parallel and perpendicular to the incline.
If E=200 GPa. a. Determine the slope at support A. b. Determine displacement at 8m from the left support.
A simply supported beam carries a concentrated load of 36 kN at 6 meters from the left support (2 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.
c. Slope at L/3. d. Deflection at L/3
A 12-meter simple beam is loaded with 3 concentrated loads P at the middle-quarters. If P = 20 kN and EI is constant. Calculate the slope at 2 meters from the left support.
From the beam shown, determine the slope at B using moment area method . Show your complete solution.
determine the sign and magnitude of (a) the slope at end C, (b) the deflection at end C using the method of superposition
The submerged curve AB is one-quarter of a circle of radius 2m and is located on the lower corner of a tank. The length of the tank perpendicular to the sketch is 4m. Find the magnitude of the total force acting on AB.