how does climate change effect the use of such materials (concrete, steel and timber) in the future for design purpose? Discuss the ways/ techniques to protect concrete, steel and timber from chemicals (soil sulphate and organic compounds) . Write about eash material separately

Q: P7.29. Compute the rotation at B and the vertical deflec- tion at D. Given: E= 200 GPa, IAC= 400 =…

A:

Q: From a given inorganic soil, the following are known: Percentage passing No. 4 Sieve - 100…

A:

Q: 3V/bh located at the midpoint of the altitude.

A: This question has been taken from mechanics

Q: Part A Learning Goal: Eccentric impact occurs when the line connecting the mass centers of two…

A:

Q: A fluid flows through a 100 m long and 120 mm diameter tube. In 2 minutes 0.15m3 of fluid passes…

A:

Q: PROBLEM 10 For pipe BC, determine the (a) flow rate (m³/s), (b) velocity (m/s), and (b) head loss…

A:

Q: What are the active earth pressure coefficient and passive earth pressure coefficient of soil, if…

A:

Q: 9. Label the centers of mass for each region on the following diagram. Label the axis of symmetry.…

A:

Q: The beam supports the loads as shown in the figure. Using E=200 GPa, w = 22 kN/m, P = 35 kN and M =…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the only one method since…

Q: За a 8a A L2 L3 a 10а

A:

Q: The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure…

A:

Q: 2. Using the information below, determine the following: a. Sketch of the traverse and label…

A:

Q: A floor system in a small building consists of wood plans supported by 50mm (nominal width) joists…

A:

Q: Sketch the load transmission of suspended and non-suspended slab to the ground

A: Load transmission- It is the procedure of transferring the load from the superstructure to the lower…

Q: am is having a fixed support in one end, and 2 roller support 3m a from the fixed support,…

A: The structure is statically indeterminate. Using moment distribution method the end moments can be…

Q: A = 3 B = 4 C = 1 D = 0   kindly answer the magnitude and if possible the forces

A:

Q: Pipes 1, 2 and 3 are 300 m, 150 m and 250 m long and 25 cm, 12 cm and 20 cm diameter with f1, f2,…

A:

Q: A small metal bar, whose initial temperature is 20°C, is dropped into a container of boiling water.…

A:

Q: Solve the problem with complete and neat solution. Draw the figure. 1. Compute the support reactions…

A:

Q: 2. For the beam and loading shown, determine the maximum flexural stress (compression and tension)…

A:

Q: PROBLEMS 5.16, 5.17 Draw the shear and bending- moment diagrams for the beam and loading shown, and…

A:

Q: Oil sg = 0.84 flowing through a pipe has a total heal loss 3ft from pt.1 to pt.2. As the figure is…

A:

Q: If the beam carries a moving uniform load of 1.19kN/m and concentrated moving load of 53 kN as…

A:

Q: draw the shear and bending moment

A:

Q: but how to get 5/18 for question 2

A: Given data for question 2: V=110 kmph R=620 m f=0.12 e=? Given data for question 3: V=? R=620 m…

Q: A 4.88 m deep, clean-earth river (n = 0.03) has a flow rate q = 13.01 m3/s/m. Compute the velocity,…

A:

Q: A contracted weir which is built in a rectangular channel has a length of weir of 1.407 m and a…

A:

Q: A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by…

A:

Q: ely. The natural frequency

A: solution of above problem is below:

Q: Valuation of real properties may be done in many ways. a.) We expect that on a per-square foot…

A:

Q: (a) Discuss the reason why the new roads need to be built in Malaysia.

A: Disclaimer Since you have asked multiple questions, we will solve the first question for you. If you…

Q: A tied column an approximately symmetrical arrangement of beams 320 mm wide and 580 mm deep results…

A:

Q: For pipe BC, determine the (a) flow rate (m³/s), (b) velocity (m/s), and (b) head loss (m). 1 cms…

A:

Q: For the beam loaded as shown, write the shear and moment equations then draw the shear and moment…

A:

Q: PROBLEM 6 A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At…

A:

Q: (b) If an accident is reported to have occurred in the daytime, what is the probability that it is a…

A:

Q: Pin support B roller A 3 m 1 m

A:

Q: Som

A:

Q: Design a two way slab using the Coefficient Method considering an interior panel (Case 2).

A:

Q: 2. Using the information below, determine the following: a. Sketch of the traverse and label…

A: Closed traverse A closed traverse is a set of connected lines whose lengths and bearings are…

Q: The pressure drop per meter length in a smooth horizontal tube in a turbulent flow depends on the…

A:

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m -1.5m- 1.5m.

A:

Q: A simple lab test for specific gravity, G, on two samples of lumber indicate that sample A has G =…

A: Based on this information alone, which wood sample would you choose as a structural member for your…

Q: If aquifer hydraulic gradient, hydraulic conductivity and effective porosity are found to be 0.4,…

A:

Q: Determine the discharge in m3/s through a trapezoidal weir whose sides are at an angle of…

A:

Q: Oil sg = 0.75 is flowing through a pipe with 6 in diameter under a pressure 15 psi. The total energy…

A:

Q: Determine the elastic section modulus, plastic modulus and the shape factor about the horizontal…

A: Solution -The given values are as…

Q: P7.17. Compute the slope and deflection under the 32-kip load at B and D. Reactions are given. I =…

A: Given, Point load at B and D =32 kips  Moment A and E =96 kips-ft. Reaction at support A,C and E =16…

Q: PROBLEMS 5.4-5.6 Draw the shear and bending- moment diagrams for the beam and loading shown. B L…

A:

Q: The oil-mercury differential reading 25 cm. Calculate the volume flow rate (in liter/ second) of oil…

A:

Reactions with Materials

Limestone